Allam power cycle

The Allam-Fetvedt Cycle or Allam Cycle is a process for converting gaseous fuels into thermal energy, while capturing the generated carbon dioxide and water. This zero emissions cycle was validated at a 50 MWth natural gas fed test facility in La Porte, Texas in May 2018. This industrial plant is owned and operated by NET Power LLC, a privately held technology licensing company. NET Power is owned by Exelon Corporation, McDermott International Ltd, Occidental Petroleum Corporation (Oxy) Low Carbon Ventures, and 8 Rivers Capital. The key inventors behind the process are English engineer Rodney John Allam, American engineer Jeremy Eron Fetvedt, and American scientist Dr. Miles R Palmer.^[1] The Allam-Fetvedt Cycle was recognized by MIT Technology Review on the 2018 list of 10 Breakthrough Technologies.^[2]

Description[]

The Allam-Fetvedt Cycle that operates as a recuperated, high-pressure, Brayton cycle employing a transcritical CO₂ working fluid with an oxy-fuel combustion regime. This cycle begins by burning a gaseous fuel with oxygen and a hot, high-pressure, recycled supercritical CO₂ working fluid in a combustor. The recycled CO₂ stream serves the dual purpose of lowering the combustion flame temperature to a manageable level and diluting the combustion products such that the cycle working fluid is predominantly CO₂. The pressure in the combustor can be as high as approximately 30 MPa and the combustion feedstock consists of approximately 95% recycled CO₂ by mass.  The combustor provides a high-pressure exhaust that can be supplied to a turbine expander operating at a pressure ratio between 6 and 12. The expander discharge leaves as a subcritical CO₂ mixture predominantly comingled with combustion derived water. This fluid enters an economizer heat exchanger, which cools the expander discharge down to below 65 °C against the stream of CO₂ that is being recycled to the combustor. Upon exiting the economizer heat exchanger, the expander exhaust is further cooled to near ambient temperature by a central cooling system, enabling liquid water to be removed from the working fluid and recycled for beneficial use.  

The remaining working fluid of nearly pure CO₂ then enters a compression and pumping stage. The compression system consists of a conventional inter-cooled centrifugal compressor with an inlet pressure below the CO₂ critical pressure. The CO₂ working fluid is compressed and then cooled to near ambient temperature in the compressor after-cooler. At this point, the combination of compressing and cooling the working fluid permits it to achieve a density in excess of 500 kg/m3. In this condition, the CO₂ stream can be pumped to the high combustion pressure required using a multi-stage centrifugal pump.  Finally, the high-pressure working fluid is sent back through the economizer heat exchanger to be reheated and returned to the combustor.

The net CO₂ product derived from the addition of fuel and oxygen in the combustor is removed from the high-pressure stream; at this point, the CO₂ product is high-pressure and high purity, ready for sequestration or utilization without requiring further compression.

^{[3][4][5][6][7][8][9]}

In order for the system to reach a high thermal efficiency, a close temperature approach is needed on the high-temperature side of the primary heat exchanger. Due to the cooling process employed at the compression and pumping stage of the Allam-Fetvedt Cycle, a large energy imbalance would typically exist in the cycle between the cooling expander exhaust flow and the reheating CO₂ recycle flow.

The Allam-Fetvedt Cycle corrects this imbalance through the incorporation of low-grade heat at the low-temperature end of the recuperative heat exchanger.  Due to the low temperatures at the cool end of the cycle, this low-grade heat only needs to be in the range of 100 °C to 400 °C.  A convenient source of this heat is the Air Separation Unit (ASU) required for the oxy-fuel combustion regime.

This basic configuration, when burning natural gas as a fuel, has been modeled to achieve an efficiency up to 60% (LHV) as a power cycle net of all parasitic loads, including the energy-intensive ASU. Despite its novelty, the components required by this cycle are all currently commercially available, with the exception of the combustion turbine package. The turbine relies on well-proven technologies and approaches used by existing gas and steam turbine design tools.^[10][11]

Applications[]

Construction began in March 2016 in La Porte, Texas on a 50 MWth industrial test facility that would showcase the Allam-Fetvedt Cycle, with construction completed in 2017. In 2018, the Allam-Fetvedt Cycle and supporting technologies were validated at this demonstration plant, which now serves as a test facility,^[12] allowing OEMs to certify components for use with future Allam-Fetvedt Cycle plants. On November 15, 2021, at approximately 7:40 pm EST the test facility successfully synchronized to the ERCOT grid ^[13] proving that the Allam Fetvedt Cycle was capable of generating power at 60 Hz. This test facility is owned and operated by NET Power, which is owned by Exelon Corporation, McDermott International Ltd, Occidental Pertroleum Corporation (Oxy) Low Carbon Ventures, and 8 Rivers Capital.   In recognition of the Allam-Fetvedt Cycle test facility in La Porte, Texas, NET Power was awarded the 2018 International Excellence in Energy Breakthrough Technological Project of the Year at the Abu Dhabi International Petroleum Exhibition and Conference (ADIPEC).^[14]

History[]

See also[]

• Oxy-fuel combustion process

References[]

External links[]

• Process diagram for natural gas
• Process diagram for coal
• Mass flow diagram
• Pressure and specific enthalpy diagram