Firestop pillow

This article does not cite any sources. Please help by adding citations to reliable sources. Unsourced material may be challenged and removed. Find sources:  –  ·  ·  · scholar · JSTOR (March 2015) (Learn how and when to remove this template message)

Firestop pillow: a passive fire protection product. This particular example consists of three layers of rockwool, two of which have been sprayed with an intumescent. The layered bundle is then inserted into a plastic bag, which is heatsealed. Other pillows use loose fills, like vermiculite with graphite poured into a fibreglass fabric bag.

Firestop pillow sample installation, alongside other firestops, used in passive fire protection of buildings.

Firestop pillow: Loose Fill/Fibreglass Bag type of firestop pillow. Usually this type of pillow contains a mixture of graphite and vermiculite.

Firestop pillow: Firestop pillows and firestop mortar used in combination at a telephone exchange in California. The pillows are used as "soft spots" to enable faster re-entries of new cables.

Firestop pillows are passive fire protection items used for firestopping holes to achieve fireproofing. The various kinds of firestop pillows are intended to slow the spread of fire. They are often used to meet fire-resistance ratings in conduits that need frequent access.

Description and use[]

Firestop pillows are passive fire protection items. They are used for firestopping holes in wall or floor assemblies to achieve fireproofing, particularly in openings that require frequent access (e.g., cable changes), requiring the removal of the firestopping and resealing after the changes are completed. The products are often required to have fire-resistance ratings and to be used in accordance with a valid certification listing, subject to listing and approval use and compliance. Pillows may present an opportunity for vandalism if not properly secured. Repairs must conform to the original certification listing.

Pillow types[]

There are three types of firestop pillows:^{[citation needed]}

• rockwool batts with intumescent resin inside plastic bags
• vermiculite with intumescent graphite inside of fibreglass bags
• intumescent foam rubber

The intumescent resins in batt-based firestop pillows contains hydrates, or chemically bound water. On the fire side, the plastic bag burns off exposing the intumescent to the fire, which releases the water in the form of vapour or steam. The steam rises and hits the plastic bag interior on the unexposed side, where it condenses back to water, and runs back down to cool the installation below. Batt-based pillows are held in place by compressing them, allowing friction to restrain them. If replaced a sufficient number of times, the pillows will retain a permanent compression, requiring their replacement with new components.

For the fabric bag based pillows, the vermiculite, the fabric bag and the graphite are noncombustible. The graphite expands but forms no bond with anything around it, unlike the resin-based intumescents. There is also no significant release of chemically bound water. Usually the bags are not entirely filled and cannot be significantly compressed, requiring mesh or grid installations to stay in place.

The foam-based pillows intumesce, swelling as a result of heat exposure.

Testing and installation[]

A hose-stream test—which is mandatory for firestops in the United States and often used in Canada—qualifies the openings and firestop pillow combinations as effective against the force of a 30 psi water stream. The pillows are compressed to provide sufficient strength to withstand the hose stream impact of the test. To accommodate larger openings that can allow the pillows to become dislodged, wire mesh is sometimes used. As a particular compression rate is required for each hole, the area of the opening less the area covered by the penetrating items is calculated, resulting in the number and size of the pillows to be installed. Without this information, there is no evidence the installation conforms with the requirements of the certification listing. As penetrants are exchanged or removed, this calculation is redone to maintain compliance with the certification listing.

An installation that meets listing and approval use and compliance usually requires pillow coverage between cables. The type and size of the pillows used must be matched to the exact cabling per the certification listing. Smoke will migrate through the interior of a cable bundle if the bundle is not opened up and sealed on the inside during the installation of any firestop, regardless of whether the firestop is intumescent or not. If mesh is used, mechanical fasteners are required, potentially negating the perceived benefits of fast installation and "re-enterability" that is typically purported to be provided by this technology.

Intumescent foam rubber firestops utilize spray foam intumescent foam, which can be extruded into various shapes. For countries that use a hose-stream test, the foam is reinforced with intumescent graphite, whereas for those who do not use a hose-stream, this ingredient is omitted.

Smokeproofing[]

Field installations of firestop pillows do not offer significant resistance to air pressure differences or smoke penetration, as is evidenced by the of North American certification listings of firestops.^{[citation needed]}

See also[]

• Listing and approval use and compliance
• Endothermic
• Intumescent
• Mineral wool
• Firestop mortar
• Passive fire protection

External links[]

Wikimedia Commons has media related to Firestop pillows.

• Würth Pillows DIBt Approval^{[dead link]}