Pennsylvania Railroad class T1

Pennsylvania Railroad T1
T1 prototype 6110 at the Baldwin plant ready for delivery to the PRR
hideType and origin Power type Steam Designer Ralph P. Johnson[1] Raymond Loewy[2] Builder Altoona Works (5500–5524) Baldwin Locomotive Works (5525–5549, 6110–6111) Pennsylvania Railroad T1 Steam Locomotive Trust (5550)[3] Serial number Altoona 4560–4584 BLW 72764–72788 (5525–5519) Build date 1942 (6110–6111) 1945–46 (5500–5549) 2014–present (5550)[3] Total produced 52
hideSpecifications Configuration: ​  • Whyte 4-4-4-4  • UIC 2′BB2′ Gauge 4 ft 8+1⁄2 in (1,435 mm) Leading dia. 36 in (914 mm) Driver dia. 80 in (2,032 mm) Trailing dia. 42 in (1,067 mm) Wheelbase 107 ft 0 in (32.61 m) Length 122 ft 9+3⁄4 in (37.43 m) Width 11 ft 1 in (3.38 m) Height 6111: 15 ft 6 in (4.72 m)[4] Axle load 71,680 lb (32.51 t) Adhesive weight 279,910 lb (127.0 t) Loco weight 502,200 lb (227.8 t) Tender weight Empty: 197,400 lb (89.54 t); Loaded: 442,500 lb (200.7 t) Total weight 944,700 lb (428.5 t) Tender type 180 P 84 Fuel type Coal Fuel capacity 85,200 lb (38.65 t) Water cap 19,200 US gal (73,000 l; 16,000 imp gal) Firebox:  • Firegrate area 92 sq ft (8.5 m2) Boiler pressure 300 lbf/in2 (2.07 MPa) Heating surface 5,639 sq ft (523.9 m2)  • Tubes and flues 4,209 sq ft (391.0 m2)  • Firebox 490 sq ft (45.5 m2) Superheater: ​  • Heating area 1,430 sq ft (132.9 m2) Cylinders Four Cylinder size 19.75 in × 26 in (502 mm × 660 mm) Valve gear Franklin poppet Valve type Poppet valves
hidePerformance figures Maximum speed Over 100 mph (160 km/h) Power output 6,500 hp (4,800 kW) Tractive effort 64,653 lbf (287.6 kN) (85%)[5] Factor of adh. 4.33
hideCareer Operators Pennsylvania Railroad Class T1 Number in class 52 original, plus 1 under construction[3] Numbers 6110, 6111, 5500-5549, 5550 Withdrawn 1952–1953[6] Preserved 0 Scrapped 1953–1956[6][3] Disposition All original 52 scrapped, 1 new build (PRR 5550) under construction

The Pennsylvania Railroad's class T1 duplex-drive 4-4-4-4 steam locomotives, introduced in 1942 (2 prototypes) and 1945-1946 (50 production), were the last steam locomotives built for the PRR and arguably its most controversial. They were ambitious, technologically sophisticated, powerful, fast and distinctively streamlined by Raymond Loewy. However, they were also prone to wheelslip both when starting and at speed, complicated to maintain and expensive to run.^{[citation needed]} The PRR decided in 1948 to place diesel locomotives on all express passenger trains, leaving unanswered questions as to whether the T1's flaws were soluble, especially taking into account that the two prototypes did not have the problems inherent to the production units. An article appearing in a 2008 issue of the Pennsylvania Railroad Technical and Historical Society Magazine showed that inadequate training for engineers transitioning to the T1 may have led to excessive throttle applications, resulting in driver slippage.^[7] Another root cause of wheelslip was faulty "spring equalization": The stiffnesses of the springs supporting the locomotive over the axles were not adjusted to properly equalize the wheel-to-track forces.^[8] The drivers were equalized together but not equalized with the engine truck. In the production fleet the PRR equalized the engine truck with the front engine and the trailing truck with the rear engine, which helped to solve the wheelslip problem.^[9]

Development[]

No. 6110, the "sister" prototype of class T1 prototype 5550. Its streamlined casing was designed by renowned industrial designer Raymond Loewy.

Before the T1, the last production express passenger engine the PRR had produced was the K4s of 1914, produced until 1928. Two experimental enlarged K5 locomotives were produced in 1929, but they weren't considered enough of an improvement to be worthwhile. After that, the PRR's attention switched to electrification and the production of electric locomotives; apparently, the railroad decided that it did not need more steam locomotives.

But the deficiencies of the K4s became more evident during the 1930s. They were fine locomotives, but as train lengths increased they proved to be underpowered; double headed K4s locomotives became the norm on many trains. The railroad had many locomotives available, but paying two crews on two locomotives per train was expensive. Meanwhile, other railroads were leaping ahead, developing increasingly-powerful passenger train locomotives. Rival New York Central built 4-6-4 Hudsons, while other roads developed passenger 4-8-2 "Mountain" type and then 4-8-4 "Northern" type designs. The PRR's steam power began to look outdated.

The PRR began to develop steam locomotives again in the mid-to-late 1930s, but with a difference. Where previous PRR locomotive policy had been conservative, new radical designs took hold. Designers from the Baldwin Locomotive Works, the PRR's longtime development partner, were eager to prove the viability of steam in the face of new competition from Diesel-electric locomotives. They persuaded the railroad to adopt Baldwin's latest idea: the duplex locomotive. This split the locomotive's driving wheels into two sets, each with its own pair of cylinders and rods. Until then, the only locomotives with two sets of drivers were articulated locomotives, but the duplex used one rigid frame. In a duplex design cylinders could be smaller, and the weight of side and main rods could be drastically-reduced. Given that the movement of the main rod could not be fully balanced, the duplex design would reduce the "hammer blow" on the track. The lower reciprocating mass meant that higher speeds could be achieved. Use of poppet valves also increased the speed because they gave very accurately timed delivery of steam to the cylinders. However, there was a drawback of the metallurgy used; the poppet valve could not withstand the stress of sustained high-speed operation (meaning over 100 mph (160 km/h) on production T1s).^{[citation needed]}

The first PRR duplex was the single experimental S1 no. 6100 of 1939. It was powerful and managed to reach 100.97 miles per hour (162.50 km/h) on level track with 1350 tons of passenger cars behind. Its performance encouraged the PRR to continue to develop duplex steam locomotives. The S1 was built unnecessarily-large for her exhibition at the 1939 New York World's Fair until October 1940; therefore, its turning radius prohibited it from operating over most of the PRR network. The 6-4-4-6 design reduced driving set traction to the point that it was especially prone to wheel slip^{[citation needed]}; thus only one Class S1 was built. The PRR returned to Baldwin to develop a duplex design fit for series production. The PRR ordered two Baldwin prototypes (nos 6110 and 6111) at a cost of $600,000 on June 26, 1940.^[10] Both prototypes had numerous teething problems and were prone to wheelslip if not handled carefully by the engineer. But favorable test reports resulted in a production order for 50 T1s, split between the PRR's own Altoona Works and Baldwin. On Dec 20, 1944, the PRR Board authorized the purchase of 50 Class T1 locomotives for $14,125,000 ($282,500 per unit). Baldwin's chief designer, Ralph P. Johnson, was responsible for the mechanical aspects of the new T1 class.^[1] Designer Raymond Loewy obtained US Patent D 136,260 for an early T1 conceptual design with a high-mounted cab located over the forward driving set.^[11] While that suited Baldwin's objective of making the most distinctive steam locomotive possible, practical considerations led the T1 design to be revised to the conventional cab position with a slight modification of the unique nose design included in Loewy's patent.

The last production T1 (no. 5549) entered service on August 27, 1946.^[12] Engine no. 5539 developed 5,012 hp (3,737 kW), as tested between September 11, 1946 and September 14, 1946 by Chesapeake and Ohio Railway dynamometer car DM-1 while on loan to C&O.^{[citation needed]} In 1944 no. 6110, tested on the stationary test plant in Altoona, developed 6,550 hp (4,880 kW) in the cylinders at 85 mph (137 km/h).^[13]

Due to their complexity relative to other steam locomotive designs, the T1s were difficult to maintain. Designed to run reliably at speeds of up to 100 mph (160 km/h), the T1s were so powerful that they could easily exceed their designed load and speed limitations, which in turn caused increased wear and tear, particularly to the 100-mph-limited poppet valves. They were described as "free steaming," meaning they could generally maintain boiler pressure regardless of throttle setting. They were so powerful that violent wheel slip could occur over a wide speed range if the engineer did not handle the throttle carefully; loss of driver traction at high speeds, especially when the T1 was under heavy load while ascending grades, caused damage to the poppet valves. A technician charged with determining the cause of frequent poppet valve failures on the T1s claimed to have observed them being operated at speeds of up to 140 mph (225 km/h) to make up time.^{[citation needed]}

A T1 prototype leaving Chicago's Union Station in February 1943 with the Manhattan Limited to New York

Fate[]

When the PRR Board decided to dieselize all first-class prime trains in 1948, most T1s were downgraded to haul secondary trains. Some of them were withdrawn from passenger service in 1949; all were out of service by 1952. They were scrapped between 1951 and 1956.

No. 5550[]

In 2014, a non-profit group known as The T1 Trust is constructing an all-new, fully-operational T1 using the original plans with subtle performance improvements where necessary.^[3] The T1 Trust's goal is to provide mainline excursion service and to set the world speed record for a steam locomotive – currently held by the LNER Class A4 4468 Mallard at 126 mph.^{[14] [15]} The T1 Trust's cost estimate to build T1 number 5550 is $10 million, with an expected completion date of 2030.^[3] The construction of 5550 is also following construction and financing methods pioneered by the LNER Peppercorn Class A1 60163 Tornado project.^[16] The first piece of the locomotive, the keystone shaped number plate, was cast in April 2014, followed by the first minor component, a driving spring link pin, in October 2014. Major components completed as of March 2019 include two Boxpok drivers, the prow, cab, third-course boiler and fire door. Front tube sheet construction was under way by a fabricator in St. Louis, Missouri.^{[17][needs update]}

In popular culture[]

• A rather loose version of the T1 appeared in the 2004 film Lemony Snicket's A Series of Unfortunate Events.

See also[]

• South Australian Railways 520 class, an Australian locomotive with similar streamlining style.
• LNER Peppercorn Class A1

References[]

Further reading[]

• Staufer, Alvin (1962). Pennsy Power. Staufer. pp. 216–225. LOC 62-20872.
• Reed, Brian (June 1972). Loco Profile 24: Pennsylvania Duplexii. Profile Publications.

External links[]

Wikimedia Commons has media related to Pennsylvania Railroad T1.

• Chesapeake & Ohio Tests the PRR T1 - Chesapeake and Ohio Historical Magazine, May 2005 by Stephenson, David R - The C&O test report contains information that is not widely known, and some of it contradicts generally accepted beliefs about the T1.
• Photos of PRR 4-4-4-4 locomotives
• An N Scale PRR T1 4-4-4-4 scratch building project
• A group that intends to build a full-size PRR T1
• YouTube video displaying the operation of T1's on the Pennsylvania Railroad - At 3 minutes and 15 seconds, an example of the T1's infamous wheel slip can be observed.