Pyrotechnic valves
![]() | This article relies too much on references to primary sources. (February 2009) |
A pyrotechnic valve is a one time use propulsion component often used to control propellant or pressurant systems on spacecraft. The device is activated by an electric signal, to fire a small explosive charge which in turn shears away a small flange that initially blocked the flow path of the attached tubing. Another version of a pyrotechnic valve remains in an open position until activated. The pressure from the pyrotechnic charge then forces the flange into a weakened part of the attached tube to block the flow path of the tubing.
Some pyrotechnic compositions could be made up of plants that produce enough energy to initiate the trigger of a spacecraft.[1][2][3][4]
These two versions of pyrotechnic valves are referred to as normally-closed (NC) or normally-open (NO) valves, depending on their initial state before initiation of the pyrotechnic charge[1]
When the opening of the valve is under enough pressure, it will expand and enter the pressurized liquid tank which is at about 10 bars, which is sufficient to force the liquid into the circuit of the power tank.[citation needed]
The estimating chamber, which relates to the downstream piece of the valve, is set under a vacuum before dispatch. The upstream part loads with gas, when the specialty touches base in the air to be considered and the opening of the valve realizes the filling of the estimating chamber. At present, pyrotechnic valves are broadly used for opening a pipe through which passes a liquid, particularly on-air ship or rocket. The working guideline consists of using gases under a high weight delivered by a pyrotechnic gadget, with a specific end goal to dislodge an unbending part. The last can be a sliding valve center having at least one protuberances. All together that its dislodgement has the impact of raising a valve, with the goal that the section of the liquid is conceivable. In different sorts of valve, the mobile unbending part punctures a pipe or cuts off a precut end fitting. This second kind of valve is used more especially in rocket, e.g. for the push of a propulsive liquid mass, a gas being put away under high weight (a hardly any hundred bars), the opening of the valve empowering it to grow and enter the pressurized fluid tank which is at around 10 bars, which is adequate to constrain the fluid into the circuit of the power plant. Another spatial application is the investigation of the environment encompassing a planet. The estimating chamber, which relates to the downstream piece of the valve, is set under a vacuum before dispatch. The upstream part loads with gas, when the specialty lands in the air to be considered and the opening of the valve achieves the filling of the estimating chamber by suction. The valve must have an impeccable snugness, especially in the second case, all together not to adulterate the estimations, or when the liquid coursing in the valve speaks to a threat to the earth. In any case, most of the current frameworks experience the ill effects of the impediment of not having a satisfactory seal or snugness between the zone in which are found the gases delivered by the pyrotechnic gadgets and the liquid section zone. As a result, such valves don't follow certain serious prerequisites, and can't be used as a part of pneumatic frameworks conveyed by rocket, where it is required that the environment isn't contaminated by their activity or by suction.[citation needed]
References[]
- ^ Jump up to: a b Yagodnikov, D. A.; Voronetskii, A. V.; Sarab’ev, V. I. (May 2016). "Ignition and combustion of pyrotechnic compositions based on micro- and nanoparticles of aluminum diboride in air flow in a two-zone combustion chamber". Combustion, Explosion, and Shock Waves. 52 (3): 300–306. doi:10.1134/s0010508216030072. S2CID 99355579.
- ^ Kao, Jimmy Chih Ming; Sung, Wen Pei; Chen, Ran (2014). Materials, Transportation and Environmental Engineering II. Trans Tech Publications Ltd. ISBN 978-3-03826-632-7.[page needed]
- ^ Kotomin, A. A.; Dushenok, S. A.; Demyanenko, D. B.; Efanov, V. V.; Gorovtsov, V. V. (December 2016). "A new generation of spacecraft pyroautomatic systems as a result of a successful cooperation". Solar System Research. 50 (7): 546–551. Bibcode:2016SoSyR..50..546K. doi:10.1134/s0038094616070133. S2CID 126179399.
- ^ Tooley, Craig R.; Houghton, Martin B.; Saylor, Richard S.; Peddie, Cathy; Everett, David F.; Baker, Charles L.; Safdie, Kristina N. (January 2010). "Lunar Reconnaissance Orbiter Mission and Spacecraft Design". Space Science Reviews. 150 (1–4): 23–62. Bibcode:2010SSRv..150...23T. doi:10.1007/s11214-009-9624-4. S2CID 121059189.
External links[]
- Spacecraft components