RF power amplifier

An RF power amplifier

Class C VHF power amplifier based on the transistor MRF317.

A radio frequency power amplifier (RF power amplifier) is a type of electronic amplifier that converts a low-power radio-frequency signal into a higher power signal.^[1] Typically, RF power amplifiers drive the antenna of a transmitter. Design goals often include gain, power output, bandwidth, power efficiency, linearity (low signal compression at rated output), input and output impedance matching, and heat dissipation.

Amplifier classes[]

Many modern RF amplifiers operate in different modes, called “classes”, to help achieve different design goals. Some classes are class A, class AB, class B, class C, which are considered the linear amplifier classes. In these classes the active device is used as a controlled current source. The bias at the input determines the class of the amplifier.

A common trade-off in power amplifier design is the trade-off between efficiency and linearity. The previously named classes become more efficient, but less linear, in the order they are listed. Operating the active device as a switch results in higher efficiency, theoretically up to 100%, but lower linearity.^[2] Among the switch-mode classes are class D, class F and class E.^[3] The class D amplifier is not often used in RF applications because the finite switching speed of the active devices and possible charge storage in saturation could lead to a large I-V product,^[2] which deteriorates efficiency.

Solid state vs. vacuum tube amplifiers[]

Modern RF power amplifiers use solid-state devices, predominantly MOSFETs (metal-oxide-semiconductor field-effect transistors).^[4][5][6] The earliest MOSFET-based RF amplifiers date back to the mid-1960s.^[7] Bipolar junction transistors were also commonly used in the past, up until they were replaced by power MOSFETs, particularly LDMOS transistors, as the standard technology for RF power amplifiers by the 1990s,^[4][6] due to the superior RF performance of LDMOS transistors.^[6]

MOSFET transistors and other modern solid-state devices have replaced vacuum tubes in most electronic devices, but tubes are still used in some high-power transmitters (see valve RF amplifier). Although mechanically robust, transistors are electrically fragile – they are easily damaged by excess voltage or current. Tubes are mechanically fragile but electrically robust – they can handle remarkably high electrical overloads without appreciable damage.

Applications[]

The basic applications of the RF power amplifier include driving to another high power source, driving a transmitting antenna and exciting microwave cavity resonators. Among these applications, driving transmitter antennas is most well known. The transmitter–receivers are used not only for voice and data communication but also for weather sensing (in the form of a radar).^{[citation needed]}

RF power amplifiers using LDMOS ( l aterally  d iffused  MOS FET) are the most widely used power semiconductor devices in wireless telecommunication networks, particularly mobile networks.^[4][8][6] LDMOS-based RF power amplifiers are widely used in digital mobile networks such as 2G, 3G,^[4][6] and 4G.^[8]

Wideband amplifier design[]

Impedance transformations over large bandwidth are difficult to realize, so conventionally, most wideband amplifiers are designed to feed a 50 Ω output load. Transistor output power is then limited to

${\displaystyle P_{\text{out}}\leq {\frac {\;\left(V_{\text{br}}-V_{\text{k}}\right)^{2}\;}{8\,Z_{\text{o}}}}~}$

where

${\displaystyle V_{\text{br}}\;}$ is defined as the breakdown voltage,

${\displaystyle V_{\text{k}}\;}$   is defined as the knee voltage,   and

${\displaystyle \;Z_{\text{o}}\;}$ is chosen so that the rated power can be met.

The external load is, by convention, ${\displaystyle \;Z_{\text{L}}=50\,\Omega \;.}$ Therefore, there must be some sort of impedance matching that transforms from ${\displaystyle \;Z_{\text{o}}\;}$ to ${\displaystyle \;Z_{\text{L}}=50\,\Omega \;.}$

The loadline method is often used in RF power amplifier design.^[9]

See also[]

• FET amplifier
• power electronics

References[]

External links[]

Wikimedia Commons has media related to RF power amplifiers.

• Fuentes, Carlos (October 2008). Microwave Power Amplifier Fundamentals (PDF) (Report). Bern, Switzerland: European Centre for Nuclear Research. Retrieved 5 March 2013.

• Khanifar, Ahmad (1 December 2014). "Wideband RF Power Amplifier Design Guidelines / RF Power Amplifier Design for Digital Predistortion". linamptech.com. Technical support. Laguna Hills, CA: Linamp Technologies, Inc. Retrieved 1 December 2014.