SNOX process

The SNOX process is a process which removes sulfur dioxide, nitrogen oxides and particulates from flue gases. The sulfur is recovered as concentrated sulfuric acid and the nitrogen oxides are reduced to free nitrogen. The process is based on the well-known wet sulfuric acid process (WSA), a process for recovering sulfur from various process gasses in the form of commercial quality sulfuric acid (H₂SO₄).^[1]^[2]^[3]

The SNOX process is based on catalytic reactions and does not consume water or absorbents. Neither does it produce any waste, except for the separated dust.

In addition the process can handle other sulfurous waste streams. This is highly interesting in refineries, where e.g. hydrogen sulfide (H₂S) gas, sour water stripper gas and Claus tail gas can be led to the SNOX plant, and thereby investment in other waste gas handling facilities can be saved.

Process[]

SNOX -flow diagram.JPG

The SNOX process includes the following steps:

Dust removal
Catalytic reduction of NO_x by adding NH₃ to the gas upstream of the SCR DeNO_x reactor
Catalytic oxidation of SO₂ to SO₃ in the oxidation reactor
Cooling of the gas to about 100 °C whereby the H₂SO₄ condenses and can be withdrawn as concentrated sulfuric acid

Applications[]

The SNOX process developed by Haldor Topsoe has been specifically designed for power and steam generation plants to remove sulfur and nitrogen oxides from combustion of heavy residuals, petroleum coke, sour gasses, or other waste products from refineries.

Today, refineries are struggling to find ways to dispose of their increasing amount of sulfurous streams and waste products. Large amounts of high-sulfur residuals, particularly heavy oil and petroleum coke, are being produced and sold as fuel to the marine market or the cement industry. These off-take markets are, however, changing due to environmental constraints, and new markets have to be identified. One attractive option would be to use these residual fuels to produce power and steam, leaving behind the issue of emissions to be addressed. The SNOX technology is especially suitable for cleaning flue gases from combustion of high-sulfur fuels in refineries. The SNOX process is a very energy-efficient way to convert the NOx in the flue gas into nitrogen and the SOx into concentrated sulfuric acid of commercial quality without using any absorbents and without producing waste products or waste water. Along with the flue gases, other sulfurous waste streams from a refinery can be treated, such as H₂S gas, sour water stripping (SWS) gas, Claus tail gas and elemental sulfur, potentially turning this technology into a complete sulfur management system.

Possible configurations:

SNOX -with H2SandSWS.JPG

Flue-gas desulfurization[]

The SNOX process can be applied for treatment of flue gases from combustion of primarily high-sulfur fuels in power stations, refinery and other industrial boilers and for treatment of other waste gases containing sulfur compounds and nitrogen oxides.

The first full scale plant treating 1,000,000 Nm³/h flue gas from a 300 MW coal-fired power plant in Denmark was started up in 1991.

The largest SNOX plant in operation treats 1,200,000 Nm³/h flue gas from four petroleum coke fired boilers at a refinery in Sicily, Italy.

The process catalytically reduces both the SO₂ and the NO_x in flue gases by more than 95% and with integration of the recovered heat from the WSA condenser it is reported to have lower operating costs than conventional technologies.^[4]^[5]

Recycling of hot combustion air from the SNOX plants to the boilers in combination with high pressure steam production in the SNOX plants increase the thermal efficiency and output of the boilers, resulting in a proportional reduction in CO₂ emission.

Enhanced sulfuric acid production[]

In several places there is a need for both electric power and sulfuric acid. A cheap high-sulfur fuel such as petroleum coke can be used for power generation, while the flue gas is cleaned in an SNOX plant producing sulfuric acid. Elemental sulfur is fired in the SNOX plant in order to produce the desired amount of sulfuric acid.

References[]

^ Sulphur recovery; (2007). The Process Principles in sulphur recovery by the WSA process. Denmark: Jens Kristen Laursen, Haldor Topsoe A/S. Reprinted from Hydrocarbonengineering August 2007^{[verification needed]}
^ Drbal, Larry (1996). Power Plant Engineering. ISBN 0412064014.^{[page needed]}
^ Laursen, J. Kr.; Karavanov, A. N. (2006). "Processes for sulfur recovery, regeneration of spent acid, and reduction of nox emissions". Chemical and Petroleum Engineering. 42 (5–6): 229–34. doi:10.1007/s10556-006-0084-3. S2CID 108517506.
^ Kohl, Arthur, L. Gas purification (5th ed.). ISBN 0-88415-220-0.^{[page needed]}
^ Noyes, Robert (1991). Handbook of pollution control processes. ISBN 0-8155-1290-2.^{[page needed]}

[1] Sulphur recovery; (2007). The Process Principles in sulphur recovery by the WSA process. Denmark: Jens Kristen Laursen, Haldor Topsoe A/S. Reprinted from Hydrocarbonengineering August 2007^{[verification needed]}

[2] Drbal, Larry (1996). Power Plant Engineering. ISBN 0412064014.^{[page needed]}

[3] Laursen, J. Kr.; Karavanov, A. N. (2006). "Processes for sulfur recovery, regeneration of spent acid, and reduction of nox emissions". Chemical and Petroleum Engineering. 42 (5–6): 229–34. doi:10.1007/s10556-006-0084-3. S2CID 108517506.

[4] Kohl, Arthur, L. Gas purification (5th ed.). ISBN 0-88415-220-0.^{[page needed]}

[5] Noyes, Robert (1991). Handbook of pollution control processes. ISBN 0-8155-1290-2.^{[page needed]}

[1]

[2]

[3]

[4]

[5]