Shell balance

This article has multiple issues. Please help or discuss these issues on the talk page. (Learn how and when to remove these template messages) This article includes a list of references, related reading or external links, but its sources remain unclear because it lacks inline citations. Please help to improve this article by introducing more precise citations. (January 2020) (Learn how and when to remove this template message) The topic of this article may not meet Wikipedia's general notability guideline. Please help to demonstrate the notability of the topic by citing reliable secondary sources that are independent of the topic and provide significant coverage of it beyond a mere trivial mention. If notability cannot be shown, the article is likely to be merged, redirected, or deleted. Find sources:  –  ·  ·  · scholar · JSTOR (January 2020) (Learn how and when to remove this template message) This article may contain an excessive amount of intricate detail that may interest only a particular audience. Please help by spinning off or relocating any relevant information, and removing excessive detail that may be against Wikipedia's inclusion policy. (January 2020) (Learn how and when to remove this template message) (Learn how and when to remove this template message)

In fluid mechanics, a shell balance can be used to determine how fluid velocity changes across a flow.

A shell is a differential element of the flow. By looking at the momentum and forces on one small portion, it is possible to integrate over the flow to see the larger picture of the flow as a whole. The balance is determining what goes into and out of the shell. Momentum is created within the shell through fluid entering and leaving the shell and by shear stress. In addition, there are pressure and gravitational forces on the shell. The goal of a shell balance is to determine the velocity profile of the flow. The velocity profile is an equation to calculate the velocity based on a specific location in the flow. From this, it is possible to find a velocity for any point across the flow.

Applications[]

Shell Balances can be used in many situations. For example, flow in a pipe, the flow of multiple fluids around each other, or flow due to pressure difference. Although terms in the shell balance and boundary conditions will change, the basic set up and process is the same.

Requirements for Shell Balance Calculations[]

The fluid must exhibit:

• Laminar flow
• No bends or curves
• Steady State
• Two boundary conditions

Boundary Conditions are used to find constants of integration.

• Fluid - Solid Boundary: No-slip condition, the velocity of a liquid at a solid is equal to the velocity of the solid.
• Liquid - Gas Boundary: Shear Stress = 0.
• Liquid - Liquid Boundary: Equal velocity and shear stress on both liquids.

Performing shell balances[]

A fluid is flowing between and in contact with two horizontal surfaces of contact area A. A differential shell of height Δy is utilized (see diagram below).

The top surface is moving at velocity U and the bottom surface is stationary.

• Density of fluid = ρ
• Viscosity of fluid = μ
• Velocity in x direction = ${\displaystyle V_{x}}$, shown by the diagonal line above. This is what a shell balance is solving for.

Conservation of Momentum is the Key of a Shell Balance

• (Rate of momentum in) - (rate of momentum out) + (sum of all forces) = 0

To perform a shell balance, follow the following basic steps:

1. Find momentum from shear stress.(Momentum from Shear Stress Into System) - (Momentum from Shear Stress Out of System). Momentum from Shear Stress goes into the shell at y and leaves the system at y + Δy. Shear stress = τ_yx, area = A, momentum = τ_yxA.
2. Find momentum from the flow. Momentum flows into the system at x = 0 and out at x = L. The flow is steady state. Therefore, the momentum flow at x = 0 is equal to the moment of flow at x = L. Therefore, these cancel out.
3. Find gravity force on the shell.
4. Find pressure forces.
5. Plug into conservation of momentum and solve for τ_yx.
6. Apply Newton's law of viscosity for a Newtonian fluidτ_yx = -μ(dV_x/dy).
7. Integrate to find the equation for velocity and use Boundary Conditions to find constants of integration.

Boundary 1: Top Surface: y = 0 and V_x = U

Boundary 2: Bottom Surface: y = D and V_x = 0

For examples of performing shell balances, visit the resources listed below.

Resources[]

• "Problem Solutions in Transport Phenomena : Fluid Mechanics Problems". Retrieved 2007-10-06.

• Harriott, Peter; W. McCabe; J. Smith (2004). Unit Operations of Chemical Engineering: Seventh Edition. McGraw-Hill Professional. pp. 68–132. ISBN 9780072848236.