Aircraft bridge
![](http://upload.wikimedia.org/wikipedia/commons/thumb/d/d6/Norwegian_Air_International_Boeing_737_EI-FHV_Stockholm_Arlanda_2019_%2801%29.jpg/220px-Norwegian_Air_International_Boeing_737_EI-FHV_Stockholm_Arlanda_2019_%2801%29.jpg)
![](http://upload.wikimedia.org/wikipedia/commons/thumb/5/57/N777UA_United_Airlines_%282971709588%29.jpg/220px-N777UA_United_Airlines_%282971709588%29.jpg)
Aircraft bridges, including taxiway bridges and runway bridges, bring aircraft traffic over motorways, railways, and waterways, and must be designed to support the heaviest aircraft that may cross them.
In 1963, a taxiway bridge at Chicago O'Hare Airport, one of the busiest airports in the world, was planned to handle future aircraft weighing 365,000 pounds (166,000 kg), but aircraft weights doubled within two years of its construction.[1] Currently, the largest passenger aircraft in the world, the Airbus A380, has a maximum take-off weight (MTOW) of 575 t (1,268,000 lb).
The largest Boeing planes, i.e. the current "Project Ozark" versions of the Boeing 747-8, are approaching MTOW of greater than 1,000,000 lb (450,000 kg). Aircraft bridges must be designed for the substantial forces exerted by aircraft braking, affecting the lateral load in substructure design.[2] Braking force of 70 percent of the live load is assumed in two recent taxiway bridge designs.[2][3] And "deck design is more apt to be controlled by punching shear than flexure due to the heavy wheel loads."[2]
Taxiway bridges are unusually wide relative to their length, and aircraft loading cannot be assumed to be distributed evenly to a bridge superstructure's web, so different modeling is required in these bridges' structural design.[4]: 2–3 In cold climates, provisions for anti-icing must be made. In the U.S., regulations of the Federal Aviation Administration must be met.[2][5] And there are various other differences versus typical bridges covered by AASHTO standards.[6]
A major issue is that closing an airport for construction even temporarily is impossible.
Major alternatives considered for construction of a taxiway bridge in 2008 were:
- use of precast, prestressed concrete I-girders
- use of precast, prestressed concrete box girders
- use of steel girders
- cast-in-place, post-tensioned concrete box girder bridge.[2]
Finite Element Analysis has been advocated for, or applied in, taxiway bridge design since at least 1963.[7]
[]
![]() | This section needs additional citations for verification. (March 2021) |
![]() | This list needs to be alphabetized. See Help:Sorting. |
![](http://upload.wikimedia.org/wikipedia/commons/thumb/b/b2/KaiTakTunnelEntrance.jpg/220px-KaiTakTunnelEntrance.jpg)
Taxiway bridges and runway bridges are bridges at airports to bring airplane taxiways and runways across motorways, railroads, or waterways. A taxiway bridge must be designed to carry the weight of the maximum size airplanes crossing and perhaps stopping directly upon it. A runway bridge is similar but may have different stresses. Alternatively, a motorway may be brought by tunnel underneath one or more runways and taxiways.
Examples include:
- At Amsterdam Schiphol Airport, the 650-metre (2,130 ft) Schiphol tunnel takes the A4 motorway underneath an airplane runway and two taxiways, and in 2003 a sixth runway was added at quite some distance west of the rest of airport, with use of two connecting taxiway bridges crossing the A5 motorway and the , respectively.
- At Manchester Airport in the United Kingdom, the A538 road runs in a pair of twin-bore tunnels underneath the southern ends of both runways.
- At Los Angeles International Airport, a tunnel was completed in 1953 allowing Sepulveda Boulevard to revert to straight and pass beneath the two runways; it was the first tunnel of its kind.[8]
- At Indianapolis International Airport, a taxiway bridge is planned to connect a future fourth runway across the Interstate 70. During 2002-04, the Indiana Department of Transportation realigned the I-70 to accommodate this.
- The third runway of the Stockholm Arlanda Airport is reached from the main terminal area by taxiway bridges constructed to be able to handle the heaviest and largest airplanes in traffic.
- The Orlando International Airport authority, planning for a future high-speed rail line, invested in extra length for its taxiway bridges over its southern airport access road.
- The Singapore Changi Airport has two taxiway bridges spanning Airport Boulevard. These bridges required shields installed on either side to shield the road from the jet blast. Planning for it since the 1990s, the airport spent S$60 million in total in modifications to support the Airbus A380.
- The Soekarno–Hatta International Airport has two taxiway bridges located in the southwest corner of the airport connecting the north and the south runway, a third taxiway bridge located in the north east corner is under construction and is scheduled to finish in 2018[9]
- the Copenhagen Airport has one runway and one taxiway running over the Denmark 221 road.
- In Norway, Sandane, Trondheim and Tromsø airports have such bridges.
- $35-million Taxiway Sierra Underpass reconstruction at Sky Harbor International Airport in Phoenix, Arizona included a $13 million five-span, cast-in-place, post-tensioned concrete box girder bridge. The airport also has the Taxiway Tango Underpass.[2][10]
- $10.5 million Port Columbus Airport Crossover Taxiway, at John Glenn Columbus International Airport, Columbus, Ohio[4]
- Taxiway B Bridge, Tampa International Airport[11]
- Taxiway bridge over Interstate 73, Piedmont Triad International Airport, Greensboro, North Carolina[3]
- Five taxiway bridges, Beijing Capital Airport[12]
- 1967-built steel girder taxiway bridge, Chicago O'Hare International Airport[13] In 1963, the weight thought to be necessary was 365,000 pounds (166,000 kg) for the 1967 built bridge. In 1969, aircraft weights had doubled. It was a 4-span welded steel girder bridge with a concrete deck, 226 feet (69 m) long, 125 feet (38 m) wide, bridge.[1] Maximum stress for the bridge was found to occur when an aircraft was 6 feet off the centerline.[14]
- Interstate 285 runs under a runway and taxiway of Atlanta's Hartsfield-Jackson International Airport[15] (and see [2]?)
- Tunnel Road East, the main entranceway to Heathrow Airport, runs under a runway and two taxiways[15]
- S. 188th Street runs under a runway and a taxiway of Seattle-Tacoma International Airport[15]
- Kai Tak Taxiway Bridge No. 3, a fast-track design-and-build contract awarded in 1993, at Hong Kong's Kai Tak Airport, which closed in 1998.[16] It is now repurposed as a road connecting Kai Tak Cruise Terminal and Shing Fung Road and Shing Cheung Road, which is now named Kai Tak Bridge [15]
- Fort Lauderdale-Hollywood International Airport has US Route 1 and an active railroad running under a runway and taxiway.[15]
- Düsseldorf International Airport has the approach end of runway 23L and the last taxiway out of the same runway 05R above a railway line. The Düsseldorf Airport Station offers a very good view of passing aircraft.
- Hua Hin Airport's runway crossed over Phet Kasem Road (Thailand Route 4) and Southern Railway Line
- Part of the taxi way and one runway of Allegheny County Airport in Pittsburgh, Pennsylvania is built on a bridge over Pennsylvania Route 885 and two sets of tracks of the Union Railroad (Pittsburgh).
- Oakland International Airport has an underpass for Ron Cowan Parkway below a taxiway connecting the commercial runways to the general aviation North Field.[17]
- Taxiways at Macau International Airport off Taipa
- Kai Tak Tunnel in New Kowloon
- Fu Hsing North Road in Taipei
Numerous taxiway bridges have been proposed but not built.
References[]
- ^ Jump up to: a b O.C. Guedelhoefer; J.R. Janney. W.R. Schriever (ed.). Evaluation of Performance by Full-Scale Testing. American Society for Testing and Materials. pp. 17–19. (book title is Full-Scale Load Testing of Structures)
- ^ Jump up to: a b c d e f Ted Bush; Kent Bormann; Rob Turton (Spring 2008). "Airport Bridges Take Off" (PDF). Aspire. Retrieved July 31, 2016.
- ^ Jump up to: a b Shane Johnson; Tom Morrison (April 10, 2015). "Design and Construction of Micropiles Supporting Taxiway Bridge" (PDF).
- ^ Jump up to: a b Kevin M. Gorak; Troy D. Jessop (Winter 2009). "A New Welcome at the Port Columbus International Airport" (PDF). Aspire: 34–37. Retrieved 17 May 2013. (with 4 pages of additional photos published in the web version)
- ^ "Advisory Circular AC 150/5300-13A" (PDF). Federal Aviation Administration. May 1, 2012.
- ^ Anthony N. Mavrogiannis, of Airport Consultants Council, Review Comments on Advisory Circular 150/5300-13, Airport Design Archived 2013-10-21 at the Wayback Machine, see esp. p.3.
- ^ Alan R. Jefts (1983). Finite Element Analysis of a Taxiway Bridge. American Society of Civil Engineers. in book Proceedings of the Eighth Conference on Electronic Computation
- ^ LAX airport diagram, 1956 shows runways 25 and 26 crossing the line of Sepulveda Boulevard (although boulevard is not indicated).
- ^ Media, Kompas Cyber (10 February 2017). "Bandara Soekarno-Hatta Bangun "East Cross Taxiway" - Kompas.com". Retrieved 18 October 2018.
- ^ David A. Burrows (October 2013). "Bridges for Planes, Trains, but not Automobiles". Structure.
- ^ "Tampa International Airport - Taxiway B Bridge Design-Build. Tampa, Florida". Finley Engineering Group. Archived from the original on 2016-08-27. Retrieved 2016-07-19.
- ^ Sun Rongmei; Zhang Xianmin. "Dynamic Analysis of the Taxiway Bridge Under Aircraft Moving Load".
- ^ Corrosion Investigation Study of Reinforcing Steel Taxiway Bridge and Spiral Ramps at Chicago-O'Hare International Airport. 1982.
- ^ [1] 1973, vol 6, pages 36-37.
- ^ Jump up to: a b c d e Google maps, accessed July 2016
- ^ Anthony Walker. Hong Kong: The Contractors' Experience. p. 89.
- ^ "CASE STUDY REPORT: OAKLAND INTERNATIONAL AIRPORT ROADWAY PROJECT" (PDF). Mineta Transportation Institute. Retrieved 2021-01-12.
External links[]
Media related to Aircraft bridges at Wikimedia Commons
- Bridges by mode of traffic
- Aviation