Library sort
![]() | This article needs additional citations for verification. (October 2017) |
Class | Sorting algorithm |
---|---|
Data structure | Array |
Worst-case performance | |
Best-case performance | |
Average performance | |
Worst-case space complexity |
Library sort, or gapped insertion sort is a sorting algorithm that uses an insertion sort, but with gaps in the array to accelerate subsequent insertions. The name comes from an analogy:
Suppose a librarian were to store their books alphabetically on a long shelf, starting with the As at the left end, and continuing to the right along the shelf with no spaces between the books until the end of the Zs. If the librarian acquired a new book that belongs to the B section, once they find the correct space in the B section, they will have to move every book over, from the middle of the Bs all the way down to the Zs in order to make room for the new book. This is an insertion sort. However, if they were to leave a space after every letter, as long as there was still space after B, they would only have to move a few books to make room for the new one. This is the basic principle of the Library Sort.
The algorithm was proposed by Michael A. Bender, Martín Farach-Colton, and in 2004[1] and was published in 2006.[2]
Like the insertion sort it is based on, library sort is a comparison sort; however, it was shown to have a high probability of running in O(n log n) time (comparable to quicksort), rather than an insertion sort's O(n2). There is no full implementation given in the paper, nor the exact algorithms of important parts, such as insertion and rebalancing. Further information would be needed to discuss how the efficiency of library sort compares to that of other sorting methods in reality.
Compared to basic insertion sort, the drawback of library sort is that it requires extra space for the gaps. The amount and distribution of that space would be implementation dependent. In the paper the size of the needed array is (1 + ε)n,[2] but with no further recommendations on how to choose ε. Moreover, it is neither adaptive nor stable. In order to warrant the with-high-probability time bounds, it requires to randomly permute the input, what changes the relative order of equal elements and shuffles any presorted input. Also, the algorithm uses binary search to find the insertion point for each element, which does not take profit of presorted input.
Another drawback is that it cannot be run as an online algorithm, because it is not possible to randomly shuffle the input. If used without this shuffling, it could easily degenerate into quadratic behaviour.
One weakness of insertion sort is that it may require a high number of swap operations and be costly if memory write is expensive. Library sort may improve that somewhat in the insertion step, as fewer elements need to move to make room, but is also adding an extra cost in the rebalancing step. In addition, locality of reference will be poor compared to mergesort as each insertion from a random data set may access memory that is no longer in cache, especially with large data sets.
Implementation[]
Algorithm[]
Let us say we have an array of n elements. We choose the gap we intend to give. Then we would have a final array of size (1 + ε)n. The algorithm works in log n rounds. In each round we insert as many elements as there are in the final array already, before re-balancing the array. For finding the position of inserting, we apply Binary Search in the final array and then swap the following elements till we hit an empty space. Once the round is over, we re-balance the final array by inserting spaces between each element.
Following are three important steps of the algorithm:
- Binary Search: Finding the position of insertion by applying binary search within the already inserted elements. This can be done by linearly moving towards left or right side of the array if you hit an empty space in the middle element.
- Insertion: Inserting the element in the position found and swapping the following elements by 1 position till an empty space is hit. This is done in logarithmic time, with high probability.
- Re-Balancing: Inserting spaces between each pair of elements in the array. The cost of rebalancing is linear in the number of elements already inserted. As these lengths increase with the powers of 2 for each round, the total cost of rebalancing is also linear.
Pseudocode[]
procedure rebalance(A, begin, end) is r ← end w ← end ÷ 2 while r ≥ begin do A[w+1] ← gap A[w] ← A[r] r ← r − 1 w ← w − 2
procedure sort(A) is n ← length(A) S ← new array of n gaps for i ← 1 to floor(log2(n) + 1) do for j ← 2^i to 2^(i + 1) do ins ← binarysearch(A[j], S, 2^(i − 1)) insert A[j] at S[ins]
Here, binarysearch(el, A, k)
performs binary search in the first k elements of A, skipping over gaps, to find a place where to locate element el. Insertion should favor gaps over filled-in elements.
References[]
- ^ Bender, Michael A.; Farach-Colton, Martín; Mosteiro, Miguel A. (1 July 2004). "Insertion Sort is O(n log n)". arXiv:cs/0407003.
- ^ a b Bender, Michael A.; Farach-Colton, Martín; Mosteiro, Miguel A. (June 2006). "Insertion Sort is O(n log n)" (PDF). Theory of Computing Systems. 39 (3): 391–397. arXiv:cs/0407003. doi:10.1007/s00224-005-1237-z. S2CID 14701669. Archived from the original (PDF) on 2017-09-08. Retrieved 2017-09-07.
External links[]
- Sorting algorithms
- Comparison sorts
- Stable sorts
- Online sorts