World file
![]() | This article needs additional citations for verification. (January 2020) |
A world file is a six line plain text sidecar file used by geographic information systems (GIS) to georeference raster map images. The file specification was introduced by Esri,[1][2] and consists of six coefficients of an affine transformation that describes the location, scale and rotation of a raster on a map
Definition[]
![](http://upload.wikimedia.org/wikipedia/en/4/41/WorldFileParametersSchemas.gif)
The generic meaning of the six parameters in a world file (as defined by Esri[1]) is:
- Line 1: A: pixel size in the x-direction in map units/pixel
- Line 2: D: rotation about y-axis
- Line 3: B: rotation about x-axis
- Line 4: E: pixel size in the y-direction in map units, almost always negative[3]
- Line 5: C: x-coordinate of the center of the upper left pixel
- Line 6: F: y-coordinate of the center of the upper left pixel
This description is however misleading in that the D and B parameters are not angular rotations, and that the A and E parameters do not correspond to the pixel size if D or B are not zero. The A, D, B and E parameters are sometimes named "x-scale", "y-skew", "x-skew" and "y-scale".
A better description of the A, D, B and E parameters is:
- Line 1: A: x-component of the pixel width (x-scale)
- Line 2: D: y-component of the pixel width (y-skew)
- Line 3: B: x-component of the pixel height (x-skew)
- Line 4: E: y-component of the pixel height (y-scale), typically negative
- Line 5: C: x-coordinate of the center of the original image's upper left pixel transformed to the map
- Line 6: F: y-coordinate of the center of the original image's upper left pixel transformed to the map
All four parameters are expressed in the map units, which are described by the spatial reference system for the raster.
When D or B are non-zero the pixel width is given by:
and the pixel height by
World files describing a map on the Universal Transverse Mercator coordinate system (UTM) use these conventions:
- D and B are usually 0, since the image pixels are usually made to align with the UTM grid
- C is the UTM easting
- F is the UTM northing
- Units are always meters per pixel
The above description applies also to a rectangular, non-rotated image which might be, for example, overlaid on an orthogonally projected map. If the world file describes an image that is rotated from the axis of the target projection, however, then A, D, B and E must be derived from the required affine transformation (see below). Specifically, A and E will no longer be the meter/pixel measurement on their respective axes.
These values are used in a six-parameter affine transformation:
which can be written as this set of equations:
where:
- x' is the calculated UTM easting of the pixel on the map
- y' is the calculated UTM northing of the pixel on the map
- x is the column number of the pixel in the image counting from left
- y is the row number of the pixel in the image counting from top
- A or x-scale; dimension of a pixel in map units in x-direction
- B, D are rotation terms
- C, F are translation terms: x, y map coordinates of the center of the upper-left pixel
- E is negative of y-scale: dimension of a pixel in map units in y-direction
The y-scale (E) is negative because the origins of an image and the UTM coordinate system are different. The origin of an image is located in the upper-left corner, whereas the origin of the map coordinate system is located in the lower-left corner. Row values in the image increase from the origin downward, while y-coordinate values in the map increase from the origin upward. Many mapping programs are unable to handle "upside down" images (i.e. those with a positive y-scale).
To go from UTM(x'y') to pixel position(x,y) one can use the equation:
Example:
Original falknermap.jpg
is 800×600 pixels (map not shown).
Its world file is falknermap.jgw
and contains:
32.0 0.0 0.0 -32.0 691200.0 4576000.0
The position of Falkner Island light on the map image is:
x = 171 pixels from left y = 343 pixels from top
This gives:
x1 = 696672 meters Easting y1 = 4565024 meters Northing
The UTM (grid) zone is not given so the coordinates are ambiguous — they can represent a position in any of the approximately 120 UTM grid zones. In this case, approximate latitude and longitude (41.2, −072.7) were looked up in a gazetteer and the UTM (grid) zone was found to be 18 using a Web-based converter.
Filename extension[]
The base filename of a world file matches the raster's base filename, but has a different filename extension (suffix). There are three filename extension naming conventions used for world files, with variable support across software.
One simple convention with widespread support is to append the letter "w" to the end of the raster filename. For example, a raster named mymap.jpg should have a world file named mymap.jpgw.
An alternative file naming convention that uses a three-character extension to conform to the 8.3 file naming convention uses the first and last character of the raster file's extension, followed by "w" at the end. For example, here are a few naming conventions for popular raster formats:
Raster format | Raster file name | World file name |
---|---|---|
GIF | mymap.gif | mymap.gfw |
JPEG | mymap.jpg | mymap.jgw |
JPEG 2000 | mymap.jp2 | mymap.j2w |
PNG | mymap.png | mymap.pgw |
TIFF | mymap.tif | mymap.tfw |
A third convention is to use a .wld file extension, irrespective of the type of raster file, as supported by GDAL and QGIS, but not Esri.[2]
Localization[]
When writing world files it is advisable to ignore localization settings and always use "." as the decimal separator. Also, negative numbers should be specified with the "-" character exclusively. This ensures maximum portability of the images.
See also[]
- Esri grid – embeds a similar georeferencing context within a single raster file
- GeoTIFF
- MapInfo TAB format - a popular geospatial vector data format for GIS software
Notes and references[]
- ^ a b "FAQ: What is the format of the world file used for georeferencing images?". Esri. 2016-05-05. Retrieved 2017-09-29.
- ^ a b Esri also has another world file format that applies to computer-aided design or CAD drawing files. That standard refers to the format of plain text computer files with names ending in .wld and is not discussed in this article.
- ^ The E parameter is often a negative number. This is because most image files store data from top to bottom, while the software utilizes traditional Cartesian coordinates with the origin in the conventional lower-left corner. If your raster appears upside-down, you may need to add a minus sign. The parameter therefore describes the map distance between consecutive image lines.
External links[]
- GIS file formats
- Cartography