Page semi-protected

Hot-air balloon

From Wikipedia, the free encyclopedia
This article is about hot-air balloons themselves. For the activity, see hot air ballooning. For other meanings, see hot air balloon (disambiguation) and air balloon (disambiguation).
"Balloon Ride" redirects here. For the song, see My First Album (Peppa Pig album).

Hot-air balloon in flight
Novelty hot-air balloons resembling anthropomorphized bees
Novelty hot-air balloon resembling the Abbey of Saint Gall – Kubicek Balloons

A hot-air balloon is a lighter-than-air aircraft consisting of a bag, called an envelope, which contains heated air. Suspended beneath is a gondola or wicker basket (in some long-distance or high-altitude balloons, a capsule), which carries passengers and a source of heat, in most cases an open flame caused by burning liquid propane. The heated air inside the envelope makes it buoyant, since it has a lower density than the colder air outside the envelope. As with all aircraft, hot-air balloons cannot fly beyond the atmosphere. The envelope does not have to be sealed at the bottom, since the air inside the envelope is at about the same pressure as the surrounding air. In modern sport balloons the envelope is generally made from nylon fabric, and the inlet of the balloon (closest to the burner flame) is made from a fire-resistant material such as Nomex. Modern balloons have been made in many shapes, such as rocket ships and the shapes of various commercial products, though the traditional shape is used for most non-commercial and many commercial applications.

The hot-air balloon is the first successful human-carrying flight technology. The first untethered manned hot-air balloon flight was performed by Jean-François Pilâtre de Rozier and François Laurent d'Arlandes on November 21, 1783, in Paris, France,[1] in a balloon created by the Montgolfier brothers.[2] The first hot-air balloon flown in the Americas was launched from the Walnut Street Jail in Philadelphia on January 9, 1793 by the French aeronaut Jean Pierre Blanchard.[3] Hot-air balloons that can be propelled through the air rather than simply drifting with the wind are known as thermal airships.

History

Main article: History of ballooning

Premodern and unmanned balloons

A sky lantern

A precursor of the hot-air balloon was the sky lantern (simplified Chinese: 孔明灯; traditional Chinese: 孔明燈). Zhuge Liang of the Shu Han kingdom, during the Three Kingdoms era (220–280 CE), used these airborne lanterns for military signaling.[4]

In the 18th century the Portuguese Jesuit priest Bartolomeu de Gusmão envisioned an aerial apparatus called Passarola, which was the predecessor of the hot-air balloon. The purpose of Passarola was to serve as air vessel in order to facilitate communication and as a strategical device.[5] In 1709 John V of Portugal decided to fund Bartolomeu de Gusmão's project following a petition made by the Jesuit priest,[6] and an unmanned demonstration was performed at Casa da India in presence of John V, the queen Maria Anna of Austria, having as witnesses the Italian cardinal Michelangelo Conti, two members of the Portuguese Royal Academy of History, one Portuguese diplomat and one chronicler. This event would bring some European attention to this event and this project. A later article dated on October 20, 1786 by the London Daily Universal Register would state that the inventor was able to raise himself by the use of his prototype. Also in 1709, the Portuguese Jesuit wrote Manifesto summário para os que ignoram poderse navegar pelo elemento do ar (Short Manifesto for those who are unaware that is possible to sail through the element air); he also left designs for a manned air vessel.

The notable balloonist Julian Nott, in the 1970s; hypothesized that two millennia ago, the Nazca Lines geoglyphs' creation could have been guided by Nazca leaders in a balloon, possibly the earliest hot-air balloon flights in human history. [7] In 1975 to support this theory, he designed and piloted the Nazca Prehistoric Balloon, using only methods and materials available to the Pre-Inca Peruvians 1,000 years ago. [8][9]

First manned flight

A model of the Montgolfier brothers' balloon at the London Science Museum

The French brothers Joseph-Michel and Jacques-Étienne Montgolfier developed a hot-air balloon in Annonay, Ardeche, France, and demonstrated it publicly on September 19, 1783, making an unmanned flight lasting 10 minutes. After experimenting with unmanned balloons and flights with animals, the first balloon flight with humans aboard, a tethered flight, performed on or around October 15, 1783, by Jean-Francois Pilatre de Rozier, who made at least one tethered flight from the yard of the Reveillon workshop in the Faubourg Saint-Antoine. Later that same day, Pilatre de Rozier became the second human to ascend into the air, reaching an altitude of 26 m (85 ft), the length of the tether.[10][11] The first free flight with human passengers was made a few weeks later, on November 21, 1783.[12] King Louis XVI had originally decreed that condemned criminals would be the first pilots, but de Rozier, along with Marquis François d'Arlandes, petitioned successfully for the honor.[13][14][15] The first military use of a hot-air balloon happened in 1794 during the battle of Fleurus, when the French used the balloon l'Entreprenant for observation.[16]

Jean-Pierre Blanchard became the first person to ever fly a hot-air balloon in various countries, including the United States, the Netherlands, and Germany. His most notable flight crossed the English Channel heading to the Dover Castle accompanied by Dr. John Jeffries, which occurred on 7 January 1785. In 1808, Blanchard fell from his balloon above The Hague and died. His wife continued his profession, but also died a decade later on a balloon, due to a firework festival causing the hydrogen in the balloon to be set on fire.[17]

Modern balloons

A hot-air balloon over the city of Helsinki in September 2009
Hot-air balloons, Cappadocia sunrise
A pair of Hopper balloons
Bristol International Balloon Fiesta

Modern hot-air balloons, with an onboard heat source, were developed by Ed Yost, beginning during the 1950s; his work resulted in his first successful flight on October 22, 1960.[18] The first modern hot-air balloon to be made in the United Kingdom (UK) was the Bristol Belle, built in 1967. Presently, hot-air balloons are used primarily for recreation.

Records

Hot-air balloons are able to fly to extremely high altitudes. On November 26, 2005 Vijaypat Singhania set the world altitude record for highest hot-air balloon flight, reaching 21,027 m (68,986 ft). He took off from downtown Mumbai, India, and landed 240 km (150 mi) south in Panchale.[19] The previous record of 19,811 m (64,997 ft) had been set by Per Lindstrand on June 6, 1988, in Plano, Texas.

On January 15, 1991, the Virgin Pacific Flyer balloon completed the longest flight in a hot-air balloon, when Per Lindstrand (born in Sweden, but resident in the UK) and Richard Branson of the UK flew 7,671.91 km (4,767.10 mi) from Japan to Northern Canada. With a volume of 74,000 cubic meters (2.6 million cubic feet), the balloon envelope was the largest ever built for a hot-air craft. Designed to fly in the trans-oceanic jet streams, the recorded the fastest ground speed for a manned balloon at 394 km/h (245 mph). The longest duration record was set by Swiss psychiatrist Bertrand Piccard (Auguste Piccard's grandson) and Briton Brian Jones, flying in the Breitling Orbiter 3. It was the first nonstop trip around the world by balloon. The balloon left Château-d'Oex, Switzerland, on March 1, 1999, and landed at 1:02 a.m. on March 21 in the Egyptian desert 500 km (300 mi) south of Cairo. The two men exceeded distance, endurance, and time records, traveling 19 days, 21 hours, and 55 minutes. Steve Fossett, flying solo, exceeded the record for briefest time traveling around the world on 3 July 2002 on his sixth attempt,[20] in 320 h 33 min.[21] Fedor Konyukhov flew solo round the world on his first attempt in a hybrid hot-air/helium balloon from 11 to 23 July 2016[22] for a round-the world time of 268 h 20 min.[21]

Construction

A hot-air balloon for manned flight uses a single-layered, fabric gas bag (lifting "envelope"), with an opening at the bottom called the mouth or throat. Attached to the envelope is a basket, or gondola, for carrying the passengers. Mounted above the basket and centered in the mouth is the "burner", which injects a flame into the envelope, heating the air within. The heater or burner is fueled by propane, a liquefied gas stored in pressure vessels, similar to high-pressure forklift cylinders.[23][24]

Envelope

Modern hot-air balloons are usually made of materials such as ripstop nylon or dacron (a polyester).[25]

A hot-air balloon is inflated partially with cold air from a gasoline-powered fan, before the propane burners are used for final inflation.

During the manufacturing process, the material is cut into panels and sewn together, along with structural load tapes that carry the weight of the gondola or basket. The individual sections, which extend from the throat to the crown (top) of the envelope, are known as gores or gore sections. Envelopes can have as few as 4 gores or as many as 24 or more.[26]

Envelopes often have a crown ring at their very top. This is a hoop of smooth metal, usually aluminium, and approximately 30 cm (1 ft) in diameter. Vertical load tapes from the envelope are attached to the crown ring.

At the bottom of the envelope the vertical load tapes are sewn into loops that are connected to cables (one cable per load tape). These cables, often referred to as flying wires, are connected to the basket by carabiners.

Seams

The most common technique for sewing panels together is called the French felled, French fell, or double lap seam.[27][28][29][30] The two pieces of fabric are folded over on each other at their common edge, possibly with a load tape as well, and sewn together with two rows of parallel stitching. Other methods include a flat lap seam, in which the two pieces of fabric are held together simply with two rows of parallel stitching, and a zigzag, where parallel zigzag stitching holds a double lap of fabric.[29]

Coatings

Hot-air balloon safari in Maasai Mara

The fabric (or at least part of it, the top 1/3, for example) may be coated with a sealer, such as silicone or polyurethane, to make it impermeable to air.[31] It is often the degradation of this coating and the corresponding loss of impermeability that ends the effective life of an envelope, not weakening of the fabric itself. Heat, moisture, and mechanical wear-and-tear during set-up and pack-up are the primary causes of degradation. Once an envelope becomes too porous to fly, it may be retired and discarded or perhaps used as a "rag bag": cold-inflated and opened for children to run through. Products for recoating the fabric are becoming available commercially.[32]

Sizes and capacity

A range of envelope sizes is available. The smallest, one-person, basket-less balloons (called "Hoppers" or "Cloudhoppers") have as little as 600 m3 (21,000 cu ft) of envelope volume;[33] for a perfect sphere the radius would be around 5 m (16 ft). At the other end of the scale, balloons used by commercial sightseeing operations may be able to carry well over two dozen people, with envelope volumes of up to 17,000 m3 (600,000 cu ft).[33] The most-used size is about 2,800 m3 (99,000 cu ft), allowing to carry 3 to 5 people.

Vents

The parachute vent at the top of an envelope, as seen from below through the mouth

The top of the balloon usually has a vent of some sort, enabling the pilot to release hot air to slow an ascent, start a descent, or increase the rate of descent, usually for landing. Some hot-air balloons have turning vents, which are side vents that, when opened, cause the balloon to rotate. Such vents are particularly useful for balloons with rectangular baskets, to facilitate aligning the wider side of the basket for landing.[34]

The most common type of top vent is a disk-shaped flap of fabric called a parachute vent, invented by Tracy Barnes.[35] The fabric is connected around its edge to a set of "vent lines" that converge in the center. (The arrangement of fabric and lines roughly resembles a parachute—thus the name.) These "vent lines" are themselves connected to a control line that runs to the basket. A parachute vent is opened by pulling on the control line. Once the control line is released, the pressure of the remaining hot air pushes the vent fabric back into place. A parachute vent can be opened briefly while in flight to initiate a rapid descent. (Slower descents are initiated by allowing the air in the balloon to cool naturally.) The vent is pulled open completely to collapse the balloon after landing.

An older, and presently less commonly used, style of top vent is called a "Velcro-style" vent. This too is a disk of fabric at the top of the balloon. However, rather than having a set of "vent lines" that can repeatedly open and close the vent, the vent is secured by "hook and loop" fasteners (such as Velcro) and is only opened at the end of the flight. Balloons equipped with a Velcro-style vent typically have a second "maneuvering vent" built into the side (as opposed to the top) of the balloon. Another common type of top design is the "smart vent", which, rather than lowering a fabric disc into the envelope as in the "parachute" type, gathers the fabric together in the center of the opening. This system can theoretically be used for in-flight maneuvering, but is more commonly used only as a rapid-deflation device for use after landing, of particular value in high winds. Other designs, such as the "pop top" and "MultiVent" systems, have also attempted to address the need for rapid deflation on landing, but the parachute top remains popular as an all-around maneuvering and deflation system.

Shape

Besides special shapes, possibly for marketing purposes, there are several variations on the traditional "inverted tear drop" shape. The simplest, often used by home builders, is a hemisphere on top of a truncated cone. More sophisticated designs attempt to minimize the circumferential stress on the fabric, with different degrees of success depending on whether they take fabric weight and varying air density into account. This shape may be referred to as "natural".[36] Finally, some specialized balloons are designed to minimize aerodynamic drag (in the vertical direction) to improve flight performance in competitions.[37]

Basket

Hot-air-balloon basket in flight
A wicker basket capable of holding 16 passengers

Baskets are commonly made of woven wicker or rattan. These materials have proven to be sufficiently light, strong, and durable for balloon flight. Such baskets are usually rectangular or triangular in shape. They vary in size from just big enough for two people to large enough to carry thirty.[38] Larger baskets often have internal partitions for structural bracing and to compartmentalize the passengers. Small holes may be woven into the side of the basket to act as foot holds for passengers climbing in or out.[39]

Baskets may also be made of aluminium, especially a collapsible aluminium frame with a fabric skin, to reduce weight or increase portability.[40] These may be used by pilots without a ground crew or who are attempting to set altitude, duration, or distance records. Other specialty baskets include the fully enclosed gondolas used for around-the-world attempts[41] and baskets that consist of little more than a seat for the pilot and perhaps one passenger.

Burner

A burner directing a flame into the envelope
Burner

The burner unit gasifies liquid propane,[42] mixes it with air, ignites the mixture, and directs the flame and exhaust into the mouth of the envelope. Burners vary in power output; each will generally produce 2 to 3 MW of heat (7 to 10 million BTUs per hour), with double, triple, or quadruple burner configurations installed where more power is needed.[43][44] The pilot actuates a burner by opening a propane valve, known as a blast valve. The valve may be spring-loaded, so that it closes automatically, or it may stay open until closed by the pilot. The burner has a pilot light to ignite the propane and air mixture. The pilot light may be lit by the pilot with an external device, such as a flint striker or a lighter, or with a built-in piezoelectric spark.[45]

Where more than one burner is present, the pilot can use one or more at a time, depending on the desired heat output. Each burner has a metal coil of propane tubing the flame shoots through to preheat the incoming liquid propane. The burner unit may be suspended from the mouth of the envelope or supported rigidly over the basket. The burner unit may be mounted on a gimbal to enable the pilot to aim the flame and avoid overheating the envelope fabric. A burner may have a secondary propane valve that releases propane more slowly and thereby generates a different sound. This is called a whisper burner and is used for flight over livestock to lessen the chance of spooking them. It also generates a more yellow flame and is used for night glows because it lights up the inside of the envelope better than the primary valve.

Fuel tanks

Propane fuel tanks are usually cylindrical pressure vessels made from aluminium, stainless steel, or titanium with a valve at one end to feed the burner and to refuel. They may have a fuel gauge and a pressure gauge. Common tank sizes are 38, 57 and 76 litres (10, 15 and 20 US gallons).[31] They may be intended for upright or horizontal use and may be mounted inside or outside the basket.

Stainless steel fuel tanks, wrapped in red insulating covers, mounted vertically, and with fuel gauges, during refueling

The pressure necessary to force the fuel through the line to the burner may be supplied by the vapor pressure of the propane itself, if warm enough, or by the introduction of an inert gas such as nitrogen.[45] Tanks may be preheated with electrical heat tapes to produce sufficient vapor pressure for cold-weather flying.[46] Warmed tanks are usually also wrapped in an insulating blanket to preserve heat during the setup and flight.

Instrumentation

A balloon may be outfitted with a variety of instruments to aid the pilot. These commonly include an altimeter, a rate-of-climb (vertical-speed) indicator known as a variometer, envelope (air) temperature, and ambient (air) temperature.[47] A GPS receiver can be useful to indicate ground speed (traditional aircraft air-speed indicators would be useless) and direction.

Combined mass

The combined mass of an average system can be calculated as follows:[31]

Component Pounds Kilograms Mass fraction
2,800 m3 (100,000 cu ft) envelope 250 113.4
3.3%
5-passenger basket 140 63.5
1.9%
Double burner 50 22.7
0.7%
3 76 L (20 US gal) fuel tanks full of propane 3 × 135 = 405 183.7
5.4%
5 passengers 5 × 150 = 750 340.2
10.0%
Subtotal 1595 723.5
21.2%
2,800 m3 (100,000 cu ft) of heated air* 5922 2686.2
78.8%
Total (3.76 tons) 7517 3409.7
100.0%
* Using a density of 0.9486 kg/m3 (0.05922 lb/cu ft) for dry air heated to 99 °C (210 °F).

Theory of operation

Generating lift

Increasing the air temperature inside the envelope makes it less dense than the surrounding (ambient) air. The balloon floats because of the buoyant force exerted on it. This force is the same force that acts on objects when they are in water and is described by Archimedes' principle. The amount of lift (or buoyancy) provided by a hot-air balloon depends primarily upon the difference between the temperature of the air inside the envelope and the temperature of the air outside the envelope. For most envelopes made of nylon fabric, the maximal internal temperature is limited to approximately 120 °C (250 °F).[48]

The melting point of nylon is significantly greater than this maximal operating temperature — about 230 °C (450 °F) — but higher temperatures cause the strength of the nylon fabric to degrade more quickly over time. With a maximal operating temperature of 120 °C (250 °F), balloon envelopes can generally be flown for between 400 and 500 hours before the fabric needs to be replaced. Many balloon pilots operate their envelopes at temperatures significantly less than the maximum to extend envelope-fabric life.

The lift generated by 2,800 m3 (100,000 cu ft) of dry air heated to various temperatures may be calculated as follows:

Air temperature Air density Air mass Lift generated
20 °C (68 °F) 1.2041 kg/m3 (0.07517 lb/cu ft) 3,409.7 kg (7,517 lb) 0 lb, 0 kg
99 °C (210 °F) 0.9486 kg/m3 (0.05922 lb/cu ft) 2,686.2 kg (5,922 lb) 723.5 kg (1,595 lb)
120 °C (248 °F) 0.8978 kg/m3 (0.05605 lb/cu ft) 2,542.4 kg (5,605 lb) 867.3 kg (1,912 lb)
Thermal image showing temperature variation in a hot-air balloon

The density of air at 20 °C (68 °F) is about 1.2 kg/m3 (0.075 lb/cu ft). The total lift for a balloon of 2,800 m3 (100,000 cu ft) heated to 99 °C (210 °F) would be 723.5 kg (1,595 lb). This is just enough to generate neutral buoyancy for the total system mass (not including the heated air trapped in the envelope, of course) stated in the previous section. Liftoff would require a slightly greater temperature, depending on the desired rate of climb. In reality, the air contained in the envelope is not all at the same temperature, as the accompanying thermal image shows, and so these calculations are based on averages.

For typical atmospheric conditions (20 °C or 68 °F), a hot-air balloon heated to 99 °C (210 °F) requires about 3.91 m3 of envelope volume to lift 1 kilogram (equivalently, 62.5 cu ft/lb). The precise amount of lift provided depends not only upon the internal temperature mentioned above, but the external temperature, altitude above sea level, and humidity of the air surrounding. On a warm day, a balloon cannot lift as much as on a cool day, because the temperature required for launch will exceed the maximum sustainable for nylon envelope fabric. Also, in the lower atmosphere, the lift provided by a hot-air balloon decreases about 3% per 1,000 m (1% per 1,000 ft) of altitude gained.[49]

Montgolfier

A Virgin hot-air balloon flying over Cambridge

Standard hot-air balloons are known as Montgolfier balloons and rely solely on the buoyancy of hot air provided by the burner and contained by the envelope.[50] This style of balloon was developed by the Montgolfier brothers and had its first public demonstration on 4 June 1783 with an unmanned flight lasting 10 minutes, followed later that year with manned flights.[51]

Hybrid

The 1785 Rozière balloon, a type of hybrid balloon, named after its creator, Jean-François Pilâtre de Rozier, has a separate cell for a lighter-than-air gas (typically helium), as well as a cone below for hot air (as is used in a hot-air balloon) to heat the helium at night. Hydrogen gas was used in the very early stages of development, but was quickly abandoned due to the danger of introducing an open flame near the gas. All modern Roziere balloons now use helium as a lifting gas.[52]

Solar

A 4-meters-high solar balloon floating over a meadow

Solar balloons are hot-air balloons that use just solar energy captured by a dark envelope to heat the air inside.[53]

Steering

Hot-air balloon can be steered to a limited degree by changing the altitude of the flight. Wind in the northern hemisphere tends to turn east due to coriolis effect as the altitude increases.

Safety equipment

To help ensure the safety of pilot and passengers, a hot-air balloon may carry several pieces of safety equipment.

In the basket

To relight the burner if the pilot light goes out and the optional piezo ignition fails, the pilot should have ready access to a means of backup ignition, such as a flint spark lighter. Many systems, especially those that carry passengers, have completely duplicate fuel and burner systems: two fuel tanks, connected to two separate hoses, which feed two distinct burners. This enables a safe landing in the case of a blockage somewhere in one system or if a system must be disabled because of a fuel leak.

A fire extinguisher suitable for extinguishing propane fires is useful. Most balloons carry a 1 or 2 kg AB:E type fire extinguisher.

A handling or drop line is mandatory safety equipment in many countries. This is a rope or webbing of 20–30 meters in length attached to the balloon basket with a quick-release connection at one end. In very calm winds the balloon pilot can throw the handling line from the balloon so that the ground crew can guide the balloon safely away from obstructions on the ground.

For commercial passenger balloons, a pilot restraint harness is mandatory in some countries. This consists of a hip belt and a webbing line that together allow for some movement while preventing the pilot from being ejected from the basket during a hard landing.

Further safety equipment may include a first-aid kit, a fire blanket and a strong rescue knife.

On the occupants

At a minimum, the pilot should wear leather or flame-retardant fiber (such as nomex) gloves, so that they may shut off a gas valve in the case of a leak, even if there is a flame present; quick action in this regard can turn a potential catastrophe into a mere inconvenience. The pilot should additionally wear flame-resistant clothing covering their arms and legs; either natural fiber, such as cotton, linen, hemp, or wool, or engineered flame-retardant fiber, such as nomex, is acceptable in this capacity. Most engineered fibers (with the exception of rayon, which is also safe to wear) are thermoplastic; many are also hydrocarbons. This makes such fabrics very much unsuitable to wear near high temperatures, since non-flame-retardant thermoplastics will melt onto the wearer, and most hydrocarbons, whether fibrous or not, are suitable to use as fuels. Natural fiber will singe rather than melt or burn readily, and flame-retardant fiber generally has a very high melting point and is intrinsically non-flammable. Many pilots also advise their passengers to wear similar protective clothing that covers their arms and legs, as well as strong shoes or boots that offer good ankle support. Finally, some balloon systems, especially those that hang the burner from the envelope instead of supporting it rigidly from the basket, require the use of helmets by the pilot and passengers.

On the ground crew

The ground crew should wear gloves whenever there is a possibility of handling ropes or lines. The mass and exposed surface to air movement of a medium-sized balloon is sufficient to cause rope friction burns to the hands of anyone trying to stop or prevent movement. The ground crew should also wear sturdy shoes and at least long pants in case of the need to access a landing or landed balloon in rough or overgrown terrain.

Maintenance and repair

Taken from the basket, the reflection of the balloon can be seen in the lake below. Obstacles in the landscape can inhibit smooth retrieval of the balloon upon landing.
A commercial balloon ride approaching its landing site at Bird-in-Hand, Pennsylvania

As with aircraft, hot-air balloons require regular maintenance to remain airworthy. As aircraft made of fabric and that lack direct horizontal control, hot-air balloons may occasionally require repairs to rips or snags. While some operations, such as cleaning and drying, may be performed by the owner or pilot, other operations, such as sewing, must be performed by a qualified repair technician and recorded in the balloon's maintenance log book.

Maintenance

To ensure long life and safe operation, the envelope should be kept clean and dry. This prevents mold and mildew from forming on the fabric and abrasion from occurring during packing, transport, and unpacking due to contact with foreign particles. In the event of a landing in a wet (because of precipitation or early morning or late evening dew) or muddy location (farmer's field), the envelope should be cleaned and laid out or hung to dry.

The burner and fuel system must also be kept clean to ensure safe operation on demand. Damaged fuel hoses need to be replaced. Stuck or leaky valves must be repaired or replaced. The wicker basket may require occasional refinishing or repair. The skids on its bottom may require occasional replacement.

Balloons in most parts of the world are maintained in accordance with a fixed manufacturer's maintenance schedule that includes regular (100 flight hours or 12 month) inspections, in addition to maintenance work to correct any damage. In Australia, balloons used for carrying commercial passengers must be inspected and maintained by approved workshops.[54]

Repair

In the case of a snag, burn, or rip in the envelope fabric, a patch may be applied or the affected panel completely replaced. Patches may be held in place with glue, tape, stitching, or a combination of these techniques. Replacing an entire panel requires the stitching around the old panel to be removed, and a new panel to be sewn in with the appropriate technique, thread, and stitch pattern.

Licensing

Depending on the size of the balloon, location, and intended use, hot-air balloons and their pilots need to comply with a variety of regulations.

Balloons

Top of balloon during inflation. Crew is securing parachute vent.

As with other aircraft in the US, balloons must be registered (have an N-number), have an airworthiness certificate, and pass annual inspections. Balloons below a certain size (empty weight of less than 155 pounds or 70 kg including envelope, basket, burners and empty fuel tanks) can be used as an ultralight aircraft.

Pilots

In Australia

In Australia, private balloon pilots are managed by the Australian Ballooning Federation[55] and typically become members of regional hot-air ballooning clubs. Commercial operations carrying fare paying passengers or charging for promotional flights must operate under an Air Operators Certificate from the Australian Civil Aviation and Safety Authority (CASA) with a nominated Chief Pilot. Pilots must have different degrees of experience before they are allowed to progress to larger balloons. Hot-air balloons must be registered aircraft with CASA and are subject to regular airworthiness checks by authorised personnel.[56]

In the UK

In the UK, the person in command must hold a valid Private Pilot's Licence issued by the Civil Aviation Authority specifically for ballooning; this is known as the PPL(B). There are two types of commercial balloon licences: CPL(B) Restricted and CPL(B) (Full). The CPL(B) Restricted is required if the pilot is undertaking work for a sponsor or being paid by an external agent to operate a balloon. The pilot can fly a sponsored balloon with everything paid for with a PPL unless asked to attend any event. Then a CPL(B) Restricted is required. The CPL(B) is required if the pilot is flying passengers for money. The balloon then needs a transport category C of A (certificate of air worthiness). If the pilot is only flying sponsor's guests and not charging money for flying other passengers, then the pilot is exempted from holding an AOC (air operator's certificate) though a copy of it is required.[clarification needed] For passenger flying the balloon also requires a maintenance log.

In the United States

In the United States, a pilot of a hot-air balloon must have a pilot certificate from the Federal Aviation Administration (FAA), carrying the rating of "Lighter-than-air free balloon", and unless the pilot is also qualified to fly gas balloons, will also carry this limitation: "Limited to hot-air balloons with airborne heater". A pilot does not need a license to fly an ultralight aircraft, but training is highly advised, and some hot-air balloons meet the criteria.

To carry paying passengers for hire (and attend some balloon festivals), a pilot must have a commercial pilot certificate. Commercial hot-air-balloon pilots may also act as hot-air-balloon flight instructors. While most balloon pilots fly for the pure joy of floating through the air, many are able to make a living as a professional balloon pilot. Some professional pilots fly commercial passenger sightseeing flights, while others fly corporate advertising balloons.[57]

Accidents and incidents

Further information: History of ballooning § Notable accidents

Manufacturers

New 2017 Cameron hot-air balloon in flight

The largest manufacturer of hot-air balloons in the world is Cameron Balloons company of Bristol, England, which also owns Lindstrand Balloons of Oswestry, England. Cameron Balloons, Lindstrand Balloons and another English balloon manufacturing company (since acquired by Cameron) have been innovators and developers of special shaped balloons. These hot-air balloons use the same principle of lift as conventional inverted teardrop-shaped balloons, but often sections of the special balloon envelope shape do not contribute to the balloon's ability to stay aloft.

The second largest manufacturer of hot-air balloons in the world is Ultramagic company, based in Spain, which produces from 80 to 120 balloons per year. Ultramagic can produce very large balloons, such as the N-500 that accommodates as many as 27 persons in the basket, and has also produced many balloons with special shapes, as well as cold-air inflatables.

One of the 3 largest companies in the world is Kubicek Balloons. From its factory in Brno, Czehia the company ships its products worldwide. Produces from 100 to 115 balloons per year. Kubicek company also focus on special shape balloons, FAA/EASA type certified and are delivered with a Standard Airworthiness Certificate.

One of the last Aerostar International, Inc. RX8 balloons

In the USA Aerostar International, Inc. of Sioux Falls, South Dakota was North America's largest balloon manufacturer and a close second in world manufacturing before ceasing to build balloons in January 2007. The oldest U.S. certified manufacture is now Adams Balloons out of Albuquerque, New Mexico. Firefly Balloons, formerly The Balloon Works, is a manufacturer of hot-air balloons in Statesville, North Carolina. Another manufacturer is of Helen, Georgia.

The major manufacturers in Canada are and . Other manufacturers include Kavanagh Balloons of Australia, Schroeder Fire Balloons of Germany, Kubicek Balloons of the Czech Republic, and LLopis Balloons of France.

See also

References

  1. ^ Tom D. Crouch (2008). Lighter Than Air. Johns Hopkins University Press. ISBN 978-0-8018-9127-4.
  2. ^ "U.S. Centennial of Flight Commisstion: Early Balloon Flight in Europe". Archived from the original on 2008-06-02. Retrieved 2008-06-04.
  3. ^ Beischer, D. E.; Fregly, A. R (January 1962). "Animals and man in space. A chronology and annotated bibliography through the year 1960" (PDF). US Naval School of Aviation Medicine. ONR TR ACR-64 (AD0272581). Retrieved 2017-07-24 – via Rubicon Foundation.
  4. ^ Deng, Yinke (2005). Ancient Chinese Inventions. Beijing: China Intercontinental Press. ISBN 9787508508375., cited in Joel Serrão, Dicionário de História de Portugal, Vol III. Porto: Livraria Figueirinhas, 1981, 184–185.
  5. ^ Arquivo Nacional da Torre do Tombo. "Cartas Consultas e Mais Obras de Alexandre de Gusmão" (páginas do manuscrito 201–209).
  6. ^ De Gusmão, Bartolomeu. "Reproduction fac-similé d'un dessin à la plume de sa description et de la pétition adressée au Jean V. (de Portugal) en langue latine et en écriture contemporaine (1709) retrouvés récemment dans les archives du Vatican du célèbre aéronef de Bartholomeu Lourenco de Gusmão "l'homme volant" portugais, né au Brésil (1685-1724) précurseur des navigateurs aériens et premier inventeur des aérostats. 1917".
  7. ^ "Innovative Projects; The Extraordinary Nazca Prehistoric Balloon". Archived from the original on 2011-07-14. Retrieved 2017-07-24.
  8. ^ "Scientist and Aviator Julian Nott Dies After a Bizarre Accident | LTA-Flight Magazine".
  9. ^ Browne, Malcolm W. (18 November 1986). "BALLOONIST HAS HIGH HOPES BUT NO ILLUSIONS". The New York Times. NY Times. Retrieved 21 June 2020.
  10. ^ Glenday, Craig (2013). Guinness world records 2014. ISBN 978-1-908843-15-9.
  11. ^ Tom D. Crouch (2009). Lighter Than Air.
  12. ^ "U.S. Centennial of Flight Commission: Early Balloon Flight in Europe". Archived from the original on 2008-06-02. Retrieved 2008-06-04.
  13. ^ "Start-Flying: History of Balloon Flying". www.start-flying.com. Retrieved 2007-12-28.
  14. ^ "Lighter than air: The Montgolfier Brothers". Retrieved 2007-12-28.
  15. ^ "National Air and Space Museum: Pioneers of Flight gallery". Retrieved 2007-12-28.
  16. ^ "Fleurus (Municipality, Province of Hainaut, Belgium)". CRW Flags Inc. Retrieved 2010-04-21.
  17. ^ Winchester, Jim (2007). A Chronology of Aviation [Sebuah Kronologi Penerbangan]. Translated by Natalia, Lucky; Dimitria, Ernest; Putra, Eddy. Amber Books. pp. 8–9. ISBN 978-623-00-1136-8.
  18. ^ Hevesi, Dennis (2007-06-04). "Ed Yost, 87, Father of Modern Hot-Air Ballooning, Dies". The New York Times. Retrieved 2008-06-04.
  19. ^ "Dr. Vijaypat Singhania enters the Guinness World Records" (PDF). Archived from the original (PDF) on 2008-06-24. Retrieved 2008-06-22.
  20. ^ Fedor Konyukhov (17 September 2016). "Experience: I flew solo around the world in a hot-air balloon". The Guardian. Retrieved 17 September 2016. Article by Konyukhov describing the experience.
  21. ^ Jump up to: a b "Balloon World Records". Fédération Aéronautique Internationale. Archived from the original on 8 September 2016. Retrieved 17 September 2016. Steve Fossett and Fedor Konyukhov, both sub-class AM-15.
  22. ^ "Fédération Aéronautique Internationale". Fédération Aéronautique Internationale. 20 June 2019. Retrieved 20 June 2019.
  23. ^ "Balloon Propane Tanks". Pilot Outlook. Archived from the original on 2011-06-10. Retrieved 2010-06-05. Propane tanks used in hot air balloons are mainly constructed of either aluminum or stainless steel. Most aluminum tanks are vertical 10-gallon cylinders (DOT 4E240), built primarily for forklift trucks.
  24. ^ "Propane Cylinders". Propane 101. Retrieved 2010-06-05. Cylinders in liquid service are commonly found on forklifts.
  25. ^ "Eballoon.org". Retrieved 2006-12-21.
  26. ^ "Head Balloons". Archived from the original on 2007-01-10. Retrieved 2007-01-12.
  27. ^ "Machine Style 56500". Arch Sewing Company. 2003. Retrieved 2010-03-06. 2 Needle Double Lap Seaming Also called Felled Seam
  28. ^ Daniel Nachbar; Paul Stumpf (2008). "Construction basics". XLTA. Retrieved 2010-03-06. all of the seams are the "French fell" type
  29. ^ Jump up to: a b Annette Petrusso. "How Things Are Made: Hot Air Balloon, The Manufacturing Process". Advameg. Retrieved 2010-03-06. The double lap seam features two rows of parallel stitching along the folded over fabric seam. A few manufactures use a flat seam.
  30. ^ Jon Radowski (2010). "How To Sew A Hot Air Balloon!". Apex Balloons. Retrieved 2010-03-06. perfect French Fell hot air balloon seam
  31. ^ Jump up to: a b c "Cameron Balloons Fuel Tanks". Retrieved 2007-03-07.
  32. ^ "Mid-Atlantic Balloon Repair: Balloon Envelope Fabric Recoating". Retrieved 2007-03-07.
  33. ^ Jump up to: a b "Lindstrand Hot Air Balloons: Cloudhopper". Archived from the original on 2009-07-01. Retrieved 2008-06-19.
  34. ^ "Avian Balloon Corporation: The Avian Envelope". Retrieved 2009-06-18.
  35. ^ "The early years of sport ballooning". David M. Wesner. Retrieved 2010-06-09.
  36. ^ "Airship and Blimp Resources: Balloon Envelope Design". Retrieved 2008-05-05.
  37. ^ "What's the Skinny on Racing Balloons?" (PDF). Archived from the original (PDF) on 2012-03-13. Retrieved 2008-05-05.
  38. ^ "Ballongflyg Upp & Ner". Archived from the original on 2010-11-13. Retrieved 2010-06-05.
  39. ^ "The Basket". Retrieved 2009-06-18.
  40. ^ Deramecourt, Arnaud (2002). "Experimental Buildings: Collapsible Basket". Retrieved 2009-06-18.
  41. ^ "Virgin Global Challenger: An Interview with Per Lindstrand". Balloon Life. 1997. Archived from the original on 2015-09-23. Retrieved 2009-06-18.
  42. ^ "The Burner". Retrieved 2011-02-14.
  43. ^ "Hot Air Dirigible Specifications". Archived from the original on 2013-05-15. Retrieved 2009-06-28.
  44. ^ "Example Balloon Configurations". Retrieved 2009-06-28.
  45. ^ Jump up to: a b "Lindstrand Fuel System: Burners & Tanks". Retrieved 2007-03-05.
  46. ^ "Nitrogen vs. Heat Tapes". Archived from the original on 2007-10-11. Retrieved 2007-11-13.
  47. ^ "Flytec 3040 Digital Wireless Instrument Package". Archived from the original on 2012-03-21. Retrieved 2006-12-26.
  48. ^ "Department of Transportation, Federal Aviation Administration, Type certificate data sheet no. A33CE" (PDF). Retrieved 2008-06-16.
  49. ^ "How to Calculate the Weight of Air and Model Hot Air Balloon Lift". Retrieved 2008-01-01.
  50. ^ "NASA: Montgolfiere balloon missions for Mars and Titan" (PDF). Archived from the original (PDF) on 2008-06-24. Retrieved 2008-06-04.
  51. ^ Scientific American Inventions and Discoveries, p. 177, Rodney P. Carlisle, John Wiley and Sons, 2004, ISBN 0-471-24410-4.
  52. ^ Amsbaugh, Allen. "Balloon Incidents". Retrieved 2009-01-16.
  53. ^ "Solar Balloons". Retrieved 2007-10-29.
  54. ^ "Ballooning Basics". Retrieved 2019-07-26.
  55. ^ "Australian Ballooning Federation". Retrieved 2015-03-28.
  56. ^ "Hot Air FAQ: What regulations are in Place?". Archived from the original on 2010-01-10. Retrieved 2009-06-22.
  57. ^ "Professional Balloon Pilots". Retrieved 2007-05-03.
  58. ^ Mohyeldin, Ayman; Gubash, Charlene; Newland, John (26 February 2013). "Foreign tourists killed in Egyptian balloon crash". World News on NBCNews.com. Archived from the original on 1 March 2013. Retrieved 26 February 2013.
  • Needham, Joseph (1986). Science and Civilization in China: Volume 4, Physics and Physical Technology, Part 2, Mechanical Engineering. Taipei: Caves Books Ltd.

External links

Library resources about
hot air balloons

General ballooning sites

Retrieved from ""