Glossary of engineering
This article may be too long to read and navigate comfortably. (September 2021) |
This glossary of engineering terms is a list of definitions about the major concepts of engineering. Please see the bottom of the page for glossaries of specific fields of engineering.
Engineering |
---|
|
A[]
- Absolute electrode potential
- In electrochemistry, according to an IUPAC definition,[1] is the electrode potential of a metal measured with respect to a universal reference system (without any additional metal–solution interface).
- Absolute pressure
- Is zero-referenced against a perfect vacuum, using an absolute scale, so it is equal to gauge pressure plus atmospheric pressure.
- Absolute zero
- The lower limit of the thermodynamic temperature scale, a state at which the enthalpy and entropy of a cooled ideal gas reach their minimum value, taken as 0. Absolute zero is the point at which the fundamental particles of nature have minimal vibrational motion, retaining only quantum mechanical, zero-point energy-induced particle motion. The theoretical temperature is determined by extrapolating the ideal gas law; by international agreement, absolute zero is taken as −273.15° on the Celsius scale (International System of Units),[2][3] which equals −459.67° on the Fahrenheit scale (United States customary units or Imperial units).[4] The corresponding Kelvin and Rankine temperature scales set their zero points at absolute zero by definition.
- Absorbance
- Absorbance or decadic absorbance is the common logarithm of the ratio of incident to transmitted radiant power through a material, and spectral absorbance or spectral decadic absorbance is the common logarithm of the ratio of incident to transmitted spectral radiant power through a material.[5]
- AC power
- Electric power delivered by alternating current; common household power is AC.
- Acceleration
- The rate at which the velocity of a body changes with time, and the direction in which that change is acting.
- Acid
- A molecule or ion capable of donating a hydron (proton or hydrogen ion H+), or, alternatively, capable of forming a covalent bond with an electron pair (a Lewis acid).[6]
- Acid–base reaction
- A chemical reaction that occurs between an acid and a base, which can be used to determine pH.
- Acid strength
- In strong acids, most of the molecules give up a hydrogen ion and become ionized.
- Acoustics
- The scientific study of sound.
- Activated sludge
- A type of wastewater treatment process for treating sewage or industrial wastewaters using aeration and a biological floc composed of bacteria and protozoa.
- Activated sludge model
- A generic name for a group of mathematical methods to model activated sludge systems.
- Active transport
- In cellular biology, active transport is the movement of molecules across a membrane from a region of their lower concentration to a region of their higher concentration—against the concentration gradient. Active transport requires cellular energy to achieve this movement. There are two types of active transport: primary active transport that uses ATP, and secondary active transport that uses an electrochemical gradient. An example of active transport in human physiology is the uptake of glucose in the intestines.
- Actuator
- A device that accepts 2 inputs (control signal, energy source) and outputs kinetic energy in the form of physical movement (linear, rotary, or oscillatory). The control signal input specifies which motion should be taken. The energy source input is typically either an electric current, hydraulic pressure, or pneumatic pressure. An actuator can be the final element of a control loop
- Adenosine triphosphate
- A complex organic chemical that provides energy to drive many processes in living cells, e.g. muscle contraction, nerve impulse propagation, chemical synthesis. Found in all forms of life, ATP is often referred to as the "molecular unit of currency" of intracellular energy transfer.[7]
- Adhesion
- The tendency of dissimilar particles or surfaces to cling to one another (cohesion refers to the tendency of similar or identical particles/surfaces to cling to one another).
- Adiabatic process
- A process where no heat energy is lost to outside space.
- Adiabatic wall
- A barrier through which heat energy cannot pass.
- Aerobic digestion
- A process in sewage treatment designed to reduce the volume of sewage sludge and make it suitable[8] for subsequent use.[9]
- Aerodynamics
- The study of the motion of air, particularly its interaction with a solid object, such as an airplane wing. It is a sub-field of fluid dynamics and gas dynamics, and many aspects of aerodynamics theory are common to these fields.
- Aerospace engineering
- Is the primary field of engineering concerned with the development of aircraft and spacecraft.[10] It has two major and overlapping branches: Aeronautical engineering and Astronautical Engineering. Avionics engineering is similar, but deals with the electronics side of aerospace engineering.
- Afocal system
- An optical system that produces no net convergence or divergence of the beam, i.e. has an infinite effective focal length.[11]
- Agricultural engineering
- The profession of designing machinery, processes, and systems for use in agriculture.
- Albedo
- A measure of the fraction of light reflected from an astronomical body or other object.
- Alkane
- An alkane, or paraffin (a historical name that also has other meanings), is an acyclic saturated hydrocarbon. In other words, an alkane consists of hydrogen and carbon atoms arranged in a tree structure in which all the carbon–carbon bonds are single.[12]
- Alkene
- An unsaturated hydrocarbon that contains at least one carbon–carbon double bond.[13] The words alkene and olefin are often used interchangeably.
- Alkyne
- Is an unsaturated hydrocarbon containing at least one carbon—carbon triple bond.[14] The simplest acyclic alkynes with only one triple bond and no other functional groups form a homologous series with the general chemical formula CnH2n−2.
- Alloy
- is a combination of metals or of a metal and another element. Alloys are defined by a metallic bonding character.[15]
- Alpha particle
- Alpha particles consist of two protons and two neutrons bound together into a particle identical to a helium-4 nucleus. They are generally produced in the process of alpha decay, but may also be produced in other ways. Alpha particles are named after the first letter in the Greek alphabet, α.
- Alternating current
- Electrical current that regularly reverses direction.
- Alternative hypothesis
- In statistical hypothesis testing, the alternative hypothesis (or maintained hypothesis or research hypothesis) and the null hypothesis are the two rival hypotheses which are compared by a statistical hypothesis test. In the domain of science two rival hypotheses can be compared by explanatory power and predictive power.
- Ammeter
- An instrument that measures current.
- Amino acids
- Are organic compounds containing amine (-NH2) and carboxyl (-COOH) functional groups, along with a side chain (R group) specific to each amino acid.[16][17][18] The key elements of an amino acid are carbon (C), hydrogen (H), oxygen (O), and nitrogen (N), although other elements are found in the side chains of certain amino acids. About 500 naturally occurring amino acids are known (though only 20 appear in the genetic code) and can be classified in many ways.[19]
- Amorphous solid
- An amorphous (from the Greek a, without, morphé, shape, form) or non-crystalline solid is a solid that lacks the long-range order that is characteristic of a crystal.
- Ampere
- The SI unit of current flow, one coulomb per second.
- Amphoterism
- In chemistry, an amphoteric compound is a molecule or ion that can react both as an acid as well as a base.[20] Many metals (such as copper, zinc, tin, lead, aluminium, and beryllium) form amphoteric oxides or hydroxides. Amphoterism depends on the oxidation states of the oxide. Al2O3 is an example of an amphoteric oxide.
- Amplifier
- A device that replicates a signal with increased power.
- Amplitude
- The amplitude of a periodic variable is a measure of its change over a single period (such as time or spatial period). There are various definitions of amplitude, which are all functions of the magnitude of the difference between the variable's extreme values. In older texts the phase is sometimes called the amplitude.[21]
- Anaerobic digestion
- Is a collection of processes by which microorganisms break down biodegradable material in the absence of oxygen.[22] The process is used for industrial or domestic purposes to manage waste or to produce fuels. Much of the fermentation used industrially to produce food and drink products, as well as home fermentation, uses anaerobic digestion.
- Angular acceleration
- Is the rate of change of angular velocity. In three dimensions, it is a pseudovector. In SI units, it is measured in radians per second squared (rad/s2), and is usually denoted by the Greek letter alpha (α).[23]
- Angular momentum
- In physics, angular momentum (rarely, moment of momentum or rotational momentum) is the rotational equivalent of linear momentum. It is an important quantity in physics because it is a conserved quantity—the total angular momentum of a system remains constant unless acted on by an external torque.
- Angular velocity
- In physics, the angular velocity of a particle is the rate at which it rotates around a chosen center point: that is, the time rate of change of its angular displacement relative to the origin (i.e. in layman's terms: how quickly an object goes around something over a period of time - e.g. how fast the earth orbits the sun). It is measured in angle per unit time, radians per second in SI units, and is usually represented by the symbol omega (ω, sometimes Ω). By convention, positive angular velocity indicates counter-clockwise rotation, while negative is clockwise.
- Anion
- Is an ion with more electrons than protons, giving it a net negative charge (since electrons are negatively charged and protons are positively charged).[24]
- Annealing (metallurgy)
- A heat treatment process that relieves internal stresses.
- Annihilation
- In particle physics, annihilation is the process that occurs when a subatomic particle collides with its respective antiparticle to produce other particles, such as an electron colliding with a positron to produce two photons.[25] The total energy and momentum of the initial pair are conserved in the process and distributed among a set of other particles in the final state. Antiparticles have exactly opposite additive quantum numbers from particles, so the sums of all quantum numbers of such an original pair are zero. Hence, any set of particles may be produced whose total quantum numbers are also zero as long as conservation of energy and conservation of momentum are obeyed.[26]
- Anode
- The electrode at which current enters a device such as an electrochemical cell or vacuum tube.
- ANSI
- The American National Standards Institute is a private non-profit organization that oversees the development of voluntary consensus standards for products, services, processes, systems, and personnel in the United States.[27] The organization also coordinates U.S. standards with international standards so that American products can be used worldwide.
- Anti-gravity
- Anti-gravity (also known as non-gravitational field) is a theory of creating a place or object that is free from the force of gravity. It does not refer to the lack of weight under gravity experienced in free fall or orbit, or to balancing the force of gravity with some other force, such as electromagnetism or aerodynamic lift.
- Applied engineering
- Is the field concerned with the application of management, design, and technical skills for the design and integration of systems, the execution of new product designs, the improvement of manufacturing processes, and the management and direction of physical and/or technical functions of a firm or organization. Applied-engineering degreed programs typically include instruction in basic engineering principles, project management, industrial processes, production and operations management, systems integration and control, quality control, and statistics.[28]
- Applied mathematics
- Mathematics used for solutions of practical problems, as opposed to pure mathematics.
- Arc length
- Arc length is the distance between two points along a section of a curve. Determining the length of an irregular arc segment is also called rectification of a curve. The advent of infinitesimal calculus led to a general formula that provides closed-form solutions in some cases.
- Archimedes' principle
- States that the upward buoyant force that is exerted on a body immersed in a fluid, whether fully or partially submerged, is equal to the weight of the fluid that the body displaces and acts in the upward direction at the center of mass of the displaced fluid.[29] Archimedes' principle is a law of physics fundamental to fluid mechanics. It was formulated by Archimedes of Syracuse.[30]
- Area moment of inertia
- The 2nd moment of area, also known as moment of inertia of plane area, area moment of inertia, or second area moment, is a geometrical property of an area which reflects how its points are distributed with regard to an arbitrary axis. The second moment of area is typically denoted with either an for an axis that lies in the plane or with a for an axis perpendicular to the plane. In both cases, it is calculated with a multiple integral over the object in question. Its dimension is L (length) to the fourth power. Its unit of dimension when working with the International System of Units is meters to the fourth power, m4.
- Arithmetic mean
- In mathematics and statistics, the arithmetic mean or simply the mean or average when the context is clear, is the sum of a collection of numbers divided by the number of numbers in the collection.[31]
- Arithmetic progression
- In mathematics, an arithmetic progression (AP) or arithmetic sequence is a sequence of numbers such that the difference between the consecutive terms is constant. Difference here means the second minus the first. For instance, the sequence 5, 7, 9, 11, 13, 15, . . . is an arithmetic progression with common difference of 2.
- Aromatic hydrocarbon
- An aromatic hydrocarbon or arene[32] (or sometimes aryl hydrocarbon)[33] is a hydrocarbon with sigma bonds and delocalized pi electrons between carbon atoms forming a circle. In contrast, aliphatic hydrocarbons lack this delocalization. The term "aromatic" was assigned before the physical mechanism determining aromaticity was discovered; the term was coined as such simply because many of the compounds have a sweet or pleasant odour. The configuration of six carbon atoms in aromatic compounds is known as a benzene ring, after the simplest possible such hydrocarbon, benzene. Aromatic hydrocarbons can be monocyclic (MAH) or polycyclic (PAH).
- Arrhenius equation
- The Arrhenius equation is a formula for the temperature dependence of reaction rates. The equation was proposed by Svante Arrhenius in 1889, based on the work of Dutch chemist Jacobus Henricus van 't Hoff who had noted in 1884 that Van 't Hoff's equation for the temperature dependence of equilibrium constants suggests such a formula for the rates of both forward and reverse reactions. This equation has a vast and important application in determining rate of chemical reactions and for calculation of energy of activation. Arrhenius provided a physical justification and interpretation for the formula.[34][35][36] Currently, it is best seen as an empirical relationship.[37]: 188 It can be used to model the temperature variation of diffusion coefficients, population of crystal vacancies, creep rates, and many other thermally-induced processes/reactions. The Eyring equation, developed in 1935, also expresses the relationship between rate and energy.
- Artificial intelligence
- (AI), is intelligence demonstrated by machines, unlike the natural intelligence displayed by humans and animals. Leading AI textbooks define the field as the study of "intelligent agents": any device that perceives its environment and takes actions that maximize its chance of successfully achieving its goals.[40] Colloquially, the term "artificial intelligence" is often used to describe machines (or computers) that mimic "cognitive" functions that humans associate with the human mind, such as "learning" and "problem solving".[41]
- Assembly language
- A computer programming language where most statements correspond to one or a few machine op-codes.
- Atomic orbital
- In atomic theory and quantum mechanics, an atomic orbital is a mathematical function that describes the wave-like behavior of either one electron or a pair of electrons in an atom.[42] This function can be used to calculate the probability of finding any electron of an atom in any specific region around the atom's nucleus. The term atomic orbital may also refer to the physical region or space where the electron can be calculated to be present, as defined by the particular mathematical form of the orbital.[43]
- Atomic packing factor
- The percentage of the volume filled with atomic mass in a crystal formation.
- Audio frequency
- An audio frequency (abbreviation: AF), or audible frequency is characterized as a periodic vibration whose frequency is audible to the average human. The SI unit of audio frequency is the hertz (Hz). It is the property of sound that most determines pitch.[44]
- Austenitization
- Austenitization means to heat the iron, iron-based metal, or steel to a temperature at which it changes crystal structure from ferrite to austenite.[45] The more open structure of the austenite is then able to absorb carbon from the iron-carbides in carbon steel. An incomplete initial austenitization can leave undissolved carbides in the matrix.[46] For some irons, iron-based metals, and steels, the presence of carbides may occur during the austenitization step. The term commonly used for this is two-phase austenitization.[47]
- Automation
- Is the technology by which a process or procedure is performed with minimum human assistance.[48] Automation[49] or automatic control is the use of various control systems for operating equipment such as machinery, processes in factories, boilers and heat treating ovens, switching on telephone networks, steering and stabilization of ships, aircraft and other applications and vehicles with minimal or reduced human intervention. Some processes have been completely automated.
- Autonomous vehicle
- A vehicle capable of driving from one point to another without input from a human operator.
- Azimuthal quantum number
- The azimuthal quantum number is a quantum number for an atomic orbital that determines its orbital angular momentum and describes the shape of the orbital. The azimuthal quantum number is the second of a set of quantum numbers which describe the unique quantum state of an electron (the others being the principal quantum number, following spectroscopic notation, the magnetic quantum number, and the spin quantum number). It is also known as the orbital angular momentum quantum number, orbital quantum number or second quantum number, and is symbolized as ℓ.
B[]
- Barometer
- A device for measuring pressure.
- Battery
- Electrochemical cells that transform chemical energy into electricity.
- Base
- In chemistry, bases are substances that, in aqueous solution, release hydroxide (OH−) ions, are slippery to the touch, can taste bitter if an alkali,[50] change the color of indicators (e.g., turn red litmus paper blue), react with acids to form salts, promote certain chemical reactions (base catalysis), accept protons from any proton donor, and/or contain completely or partially displaceable OH− ions.
- Baud
- Rate at which data is transferred in symbols/second; a symbol may represent one or more bits.
- Beam
- A structural element whose length is significantly greater than its width or height.
- Beer–Lambert law
- The Beer–Lambert law, also known as Beer's law, the Lambert–Beer law, or the Beer–Lambert–Bouguer law relates the attenuation of light to the properties of the material through which the light is travelling. The law is commonly applied to chemical analysis measurements and used in understanding attenuation in physical optics, for photons, neutrons or rarefied gases. In mathematical physics, this law arises as a solution of the BGK equation.
- Belt
- A closed loop of flexible material used to transmit mechancial power from one pulley to another.
- Belt friction
- Is a term describing the friction forces between a belt and a surface, such as a belt wrapped around a bollard. When one end of the belt is being pulled only part of this force is transmitted to the other end wrapped about a surface. The friction force increases with the amount of wrap about a surface and makes it so the tension in the belt can be different at both ends of the belt. Belt friction can be modeled by the Belt friction equation.[51]
- Bending
- In applied mechanics, bending (also known as flexure) characterizes the behavior of a slender structural element subjected to an external load applied perpendicularly to a longitudinal axis of the element. The structural element is assumed to be such that at least one of its dimensions is a small fraction, typically 1/10 or less, of the other two.[52]
- Bending moment
- In solid mechanics, a bending moment is the reaction induced in a structural element when an external force or moment is applied to the element, causing the element to bend.[53] [54] The most common or simplest structural element subjected to bending moments is the beam.
- Benefit–cost analysis
- Cost–benefit analysis (CBA), sometimes called benefit costs analysis (BCA), is a systematic approach to estimating the strengths and weaknesses of alternatives (for example in transactions, activities, functional business requirements); it is used to determine options that provide the best approach to achieve benefits while preserving savings.[55] It may be used to compare potential (or completed) courses of actions; or estimate (or evaluate) the value against costs of a single decision, project, or policy.
- Bernoulli differential equation
- In mathematics, an ordinary differential equation of the form:
- Bernoulli's equation
- An equation for relating several measurements within a fluid flow, such as velocity, pressure, and potential energy.
- Bernoulli's principle
- In fluid dynamics, Bernoulli's principle states that an increase in the speed of a fluid occurs simultaneously with a decrease in pressure or a decrease in the fluid's potential energy.[57]: Ch.3 [58]: § 3.5 The principle is named after Daniel Bernoulli who published it in his book Hydrodynamica in 1738.[59] Although Bernoulli deduced that pressure decreases when the flow speed increases, it was Leonhard Euler who derived Bernoulli's equation in its usual form in 1752.[60][61] The principle is only applicable for isentropic flows: when the effects of irreversible processes (like turbulence) and non-adiabatic processes (e.g. heat radiation) are small and can be neglected.
- Beta particle
- also called beta ray or beta radiation (symbol β), is a high-energy, high-speed electron or positron emitted by the radioactive decay of an atomic nucleus during the process of beta decay. There are two forms of beta decay, β− decay and β+ decay, which produce electrons and positrons respectively.[62]
- Binomial distribution
- In probability theory and statistics, the binomial distribution with parameters n and p is the discrete probability distribution of the number of successes in a sequence of n independent experiments, each asking a yes–no question, and each with its own boolean-valued outcome: a random variable containing a single bit of information: success/yes/true/one (with probability p) or failure/no/false/zero (with probability q = 1 − p). A single success/failure experiment is also called a Bernoulli trial or Bernoulli experiment and a sequence of outcomes is called a Bernoulli process; for a single trial, i.e., n = 1, the binomial distribution is a Bernoulli distribution. The binomial distribution is the basis for the popular binomial test of statistical significance.
- Biocatalysis
- Biocatalysis refers to the use of living (biological) systems or their parts to speed up (catalyze) chemical reactions. In biocatalytic processes, natural catalysts, such as enzymes, perform chemical transformations on organic compounds. Both enzymes that have been more or less isolated and enzymes still residing inside living cells are employed for this task.[63][64][65] The modern usage of biotechnologically produced and possibly modified enzymes for organic synthesis is termed chemoenzymatic synthesis; the reactions performed are chemoenzymatic reactions.
- Biomedical engineering
- Biomedical Engineering (BME) or Medical Engineering is the application of engineering principles and design concepts to medicine and biology for healthcare purposes (e.g. diagnostic or therapeutic). This field seeks to close the gap between engineering and medicine, combining the design and problem solving skills of engineering with medical biological sciences to advance health care treatment, including diagnosis, monitoring, and therapy.[66]
- Biomimetic
- Biomimetics or biomimicry is the imitation of the models, systems, and elements of nature for the purpose of solving complex human problems.[67]
- Bionics
- The application of biological methods to engineering systems.
- Biophysics
- Is an interdisciplinary science that applies approaches and methods traditionally used in physics to study biological phenomena.[68][69][70] Biophysics covers all scales of biological organization, from molecular to organismic and populations. Biophysical research shares significant overlap with biochemistry, molecular biology, physical chemistry, physiology, nanotechnology, bioengineering, computational biology, biomechanics and systems biology.
- Biot number
- The Biot number (Bi) is a dimensionless quantity used in heat transfer calculations. It is named after the eighteenth century French physicist Jean-Baptiste Biot (1774–1862), and gives a simple index of the ratio of the heat transfer resistances inside of and at the surface of a body. This ratio determines whether or not the temperatures inside a body will vary significantly in space, while the body heats or cools over time, from a thermal gradient applied to its surface.
- Block and tackle
- A system of pulleys and a rope threaded between them, used to lift or pull heavy loads.
- Body force
- Is a force that acts throughout the volume of a body. Forces due to gravity, electric fields and magnetic fields are examples of body forces. Body forces contrast with contact forces or surface forces which are exerted to the surface of an object.
- Boiler
- Is a closed vessel in which fluid (generally water) is heated. The fluid does not necessarily boil. The heated or vaporized fluid exits the boiler for use in various processes or heating applications,[71][72] including water heating, central heating, boiler-based power generation, cooking, and sanitation.
- Boiling point
- The boiling point of a substance is the temperature at which the vapor pressure of a liquid equals the pressure surrounding the liquid[73][74] and the liquid changes into a vapor.
- Boiling-point elevation
- Boiling-point elevation describes the phenomenon that the boiling point of a liquid (a solvent) will be higher when another compound is added, meaning that a solution has a higher boiling point than a pure solvent. This happens whenever a non-volatile solute, such as a salt, is added to a pure solvent, such as water. The boiling point can be measured accurately using an ebullioscope.
- Boltzmann constant
- The Boltzmann constant (kB or k) is a physical constant relating the average kinetic energy of particles in a gas with the temperature of the gas[75] and occurs in Planck's law of black-body radiation and in Boltzmann's entropy formula. It was introduced by Max Planck, but named after Ludwig Boltzmann.
It is the gas constant R divided by the Avogadro constant NA:
- .
C[]
- Calculus
- The mathematics of change.
- Capacitance
- The ability of a body to store electrical charge.
- Capacitive reactance
- The impedance of a capacitor in an alternating current circuit, the opposition to current flow.
- Capacitor
- An electrical component that stores energy in an electric field.
- Capillary action
- Capillary action (sometimes capillarity, capillary motion, capillary effect, or wicking) is the ability of a liquid to flow in narrow spaces without the assistance of, or even in opposition to, external forces like gravity. The effect can be seen in the drawing up of liquids between the hairs of a paint-brush, in a thin tube, in porous materials such as paper and plaster, in some non-porous materials such as sand and liquefied carbon fiber, or in a cell. It occurs because of intermolecular forces between the liquid and surrounding solid surfaces. If the diameter of the tube is sufficiently small, then the combination of surface tension (which is caused by cohesion within the liquid) and adhesive forces between the liquid and container wall act to propel the liquid.[96]
- Carbonate
- Any mineral with bound carbon dioxide.
- Carnot cycle
- A hypothetical thermodynamic cycle for a heat engine; no thermodynamic cycle can be more efficient than a Carnot cycle operating between the same two temperature limits.
- Cartesian coordinates
- Coordinates within a rectangular Cartesian plane.
- Castigliano's method
- Named for Carlo Alberto Castigliano, is a method for determining the displacements of a linear-elastic system based on the partial derivatives of the energy. He is known for his two theorems. The basic concept may be easy to understand by recalling that a change in energy is equal to the causing force times the resulting displacement. Therefore, the causing force is equal to the change in energy divided by the resulting displacement. Alternatively, the resulting displacement is equal to the change in energy divided by the causing force. Partial derivatives are needed to relate causing forces and resulting displacements to the change in energy.
- Casting
- Forming of an object by pouring molten metal (or other substances) into a mold.
- Cathode
- The terminal of a device by which current exits.
- Cathode ray
- The stream of electrons emitted from a heated negative electrode and attracted to a positive electrode.
- Cell membrane
- The cell membrane (also known as the plasma membrane or cytoplasmic membrane, and historically referred to as the plasmalemma) is a biological membrane that separates the interior of all cells from the outside environment (the extracellular space) which protects the cell from its environment[97][98] consisting of a lipid bilayer with embedded proteins.
- Cell nucleus
- In cell biology, the nucleus (pl. nuclei; from Latin nucleus or nuculeus, meaning kernel or seed) is a membrane-enclosed organelle found in eukaryotic cells. Eukaryotes usually have a single nucleus, but a few cell types, such as mammalian red blood cells, have no nuclei, and a few others including osteoclasts have many.
- Cell theory
- In biology, cell theory is the historic scientific theory, now universally accepted, that living organisms are made up of cells, that they are the basic structural/organizational unit of all organisms, and that all cells come from pre-existing cells. Cells are the basic unit of structure in all organisms and also the basic unit of reproduction.
- Center of gravity
- The center of mass of an object, its balance point.
- Center of mass
- The weighted center of an object; a force applied through the center of mass will not cause rotation of the object.
- Center of pressure
- Is the point where the total sum of a pressure field acts on a body, causing a force to act through that point. The total force vector acting at the center of pressure is the value of the integrated vectorial pressure field. The resultant force and center of pressure location produce equivalent force and moment on the body as the original pressure field.
- Central force motion
- .
- Central limit theorem
- In probability theory, the central limit theorem (CLT) establishes that, in some situations, when independent random variables are added, their properly normalized sum tends toward a normal distribution (informally a "bell curve") even if the original variables themselves are not normally distributed. The theorem is a key concept in probability theory because it implies that probabilistic and statistical methods that work for normal distributions can be applicable to many problems involving other types of distributions.
- Central processing unit
- A central processing unit (CPU) is the electronic circuitry within a computer that carries out the instructions of a computer program by performing the basic arithmetic, logic, controlling and input/output (I/O) operations specified by the instructions. The computer industry has used the term "central processing unit" at least since the early 1960s.[99] Traditionally, the term "CPU" refers to a processor, more specifically to its processing unit and control unit (CU), distinguishing these core elements of a computer from external components such as main memory and I/O circuitry.[100]
- Centripetal acceleration
- .
- Centripetal force
- A force acting against rotational acceleration.
- Centroid
- The average point of volume for an object.
- Centrosome
- In cell biology, the centrosome is an organelle that serves as the main microtubule organizing center (MTOC) of the animal cell as well as a regulator of cell-cycle progression. The centrosome is thought to have evolved only in the metazoan lineage of eukaryotic cells.[101] Fungi and plants lack centrosomes and therefore use structures other than MTOCs to organize their microtubules.[102][103]
- Chain reaction
- Is a sequence of reactions where a reactive product or by-product causes additional reactions to take place. In a chain reaction, positive feedback leads to a self-amplifying chain of events.
- Change of base rule
- .
- Charles's law
- Charles's law (also known as the law of volumes) is an experimental gas law that describes how gases tend to expand when heated. A modern statement of Charles's law is: When the pressure on a sample of a dry gas is held constant, the Kelvin temperature and the volume will be in direct proportion.[104]
- Chemical bond
- Is a lasting attraction between atoms, ions or molecules that enables the formation of chemical compounds. The bond may result from the electrostatic force of attraction between oppositely charged ions as in ionic bonds or through the sharing of electrons as in covalent bonds. The strength of chemical bonds varies considerably; there are "strong bonds" or "primary bonds" such as covalent, ionic and metallic bonds, and "weak bonds" or "secondary bonds" such as dipole–dipole interactions, the London dispersion force and hydrogen bonding.
- Chemical compound
- Is a chemical substance composed of many identical molecules (or molecular entities) composed of atoms from more than one element held together by chemical bonds. A chemical element bonded to an identical chemical element is not a chemical compound since only one element, not two different elements, is involved.
- Chemical equilibrium
- In a chemical reaction, chemical equilibrium is the state in which both reactants and products are present in concentrations which have no further tendency to change with time, so that there is no observable change in the properties of the system.[105] Usually, this state results when the forward reaction proceeds at the same rate as the reverse reaction. The reaction rates of the forward and backward reactions are generally not zero, but equal. Thus, there are no net changes in the concentrations of the reactant(s) and product(s). Such a state is known as dynamic equilibrium.[106][107]
- Chemical kinetics
- Chemical kinetics, also known as reaction kinetics, is the study of rates of chemical processes. Chemical kinetics includes investigations of how different experimental conditions can influence the speed of a chemical reaction and yield information about the reaction's mechanism and transition states, as well as the construction of mathematical models that can describe the characteristics of a chemical reaction.
- Chemical reaction
- A chemical reaction is a process that leads to the chemical transformation of one set of chemical substances to another.[108] Classically, chemical reactions encompass changes that only involve the positions of electrons in the forming and breaking of chemical bonds between atoms, with no change to the nuclei (no change to the elements present), and can often be described by a chemical equation. Nuclear chemistry is a sub-discipline of chemistry that involves the chemical reactions of unstable and radioactive elements where both electronic and nuclear changes can occur.
- Chemistry
- Is the scientific discipline involved with elements and compounds composed of atoms, molecules and ions: their composition, structure, properties, behavior and the changes they undergo during a reaction with other substances.[109][110][111][112]
- Chloride
- Any chemical compound containing the element chlorine.
- Chromate
- Chromate salts contain the chromate anion, CrO2−
4. Dichromate salts contain the dichromate anion, Cr
2O2−
7. They are oxoanions of chromium in the 6+ oxidation state . They are moderately strong oxidizing agents. In an aqueous solution, chromate and dichromate ions can be interconvertible. - Circular motion
- In physics, circular motion is a movement of an object along the circumference of a circle or rotation along a circular path. It can be uniform, with constant angular rate of rotation and constant speed, or non-uniform with a changing rate of rotation. The rotation around a fixed axis of a three-dimensional body involves circular motion of its parts. The equations of motion describe the movement of the center of mass of a body.
- Civil engineering
- The profession that deals with the design and construction of structures, or other fixed works.
- Clausius–Clapeyron relation
- The Clausius–Clapeyron relation, named after Rudolf Clausius[113] and Benoît Paul Émile Clapeyron,[114] is a way of characterizing a discontinuous phase transition between two phases of matter of a single constituent. On a pressure–temperature (P–T) diagram, the line separating the two phases is known as the coexistence curve. The Clausius–Clapeyron relation gives the slope of the tangents to this curve. Mathematically,
- Clausius inequality
- .
- Clausius theorem
- The Clausius theorem (1855) states that a system exchanging heat with external reservoirs and undergoing a cyclic process, is one that ultimately returns a system to its original state,
- Coefficient of performance
- The coefficient of performance or COP (sometimes CP or CoP) of a heat pump, refrigerator or air conditioning system is a ratio of useful heating or cooling provided to work required.[119][120] Higher COPs equate to lower operating costs. The COP usually exceeds 1, especially in heat pumps, because, instead of just converting work to heat (which, if 100% efficient, would be a COP_hp of 1), it pumps additional heat from a heat source to where the heat is required. For complete systems, COP calculations should include energy consumption of all power consuming auxiliaries. COP is highly dependent on operating conditions, especially absolute temperature and relative temperature between sink and system, and is often graphed or averaged against expected conditions.[121]
- Coefficient of variation
- In probability theory and statistics, the coefficient of variation (CV), also known as relative standard deviation (RSD), is a standardized measure of dispersion of a probability distribution or frequency distribution. It is often expressed as a percentage, and is defined as the ratio of the standard deviation to the mean (or its absolute value, ).
- Coherence
- In physics, two wave sources are perfectly coherent if they have a constant phase difference and the same frequency, and the same waveform. Coherence is an ideal property of waves that enables stationary (i.e. temporally and spatially constant) interference. It contains several distinct concepts, which are limiting cases that never quite occur in reality but allow an understanding of the physics of waves, and has become a very important concept in quantum physics. More generally, coherence describes all properties of the correlation between physical quantities of a single wave, or between several waves or wave packets.
- Cohesion
- Or cohesive attraction or cohesive force is the action or property of like molecules sticking together, being mutually attractive. It is an intrinsic property of a substance that is caused by the shape and structure of its molecules, which makes the distribution of orbiting electrons irregular when molecules get close to one another, creating electrical attraction that can maintain a microscopic structure such as a water drop. In other words, cohesion allows for surface tension, creating a "solid-like" state upon which light-weight or low-density materials can be placed.
- Cold forming
- Or cold working, any metal-working procedure (such as hammering, rolling, shearing, bending, milling, etc.) carried out below the metal's recrystallization temperature.
- Combustion
- Or burning,[122] is a high-temperature exothermic redox chemical reaction between a fuel (the reductant) and an oxidant, usually atmospheric oxygen, that produces oxidized, often gaseous products, in a mixture termed as smoke.
- Compensation
- Is planning for side effects or other unintended issues in a design. In a more simpler term, it's a "counter-procedure" plan on expected side effect performed to produce more efficient and useful results. The design of an invention can itself also be to compensate for some other existing issue or exception.
- Compiler
- A computer program that translates a high-level language into machine language.
- Compressive strength
- Compressive strength or compression strength is the capacity of a material or structure to withstand loads tending to reduce size, as opposed to tensile strength, which withstands loads tending to elongate. In other words, compressive strength resists compression (being pushed together), whereas tensile strength resists tension (being pulled apart). In the study of strength of materials, tensile strength, compressive strength, and shear strength can be analyzed independently.
- Computational fluid dynamics
- The numerical solution of flow equations in practical problems such as aircraft design or hydraulic structures.
- Computer
- A computer is a device that can be instructed to carry out sequences of arithmetic or logical operations automatically via computer programming. Modern computers have the ability to follow generalized sets of operations, called programs. These programs enable computers to perform an extremely wide range of tasks.
- Computer-aided design
- Computer-aided design (CAD) is the use of computer systems (or workstations) to aid in the creation, modification, analysis, or optimization of a design.[123] CAD software is used to increase the productivity of the designer, improve the quality of design, improve communications through documentation, and to create a database for manufacturing.[124] CAD output is often in the form of electronic files for print, machining, or other manufacturing operations. The term CADD (for Computer Aided Design and Drafting) is also used.[125]
- Computer-aided engineering
- Computer-aided engineering (CAE) is the broad usage of computer software to aid in engineering analysis tasks. It includes finite element analysis (FEA), computational fluid dynamics (CFD), multibody dynamics (MBD), durability and optimization.
- Computer-aided manufacturing
- Computer-aided manufacturing (CAM) is the use of software to control machine tools and related ones in the manufacturing of workpieces.[126][127][128][129][130] This is not the only definition for CAM, but it is the most common;[126] CAM may also refer to the use of a computer to assist in all operations of a manufacturing plant, including planning, management, transportation and storage.[131][132]
- Computer engineering
- Computer engineering is a discipline that integrates several fields of computer science and electronics engineering required to develop computer hardware and software.[133]
- Computer science
- Is the theory, experimentation, and engineering that form the basis for the design and use of computers. It involves the study of algorithms that process, store, and communicate digital information. A computer scientist specializes in the theory of computation and the design of computational systems.[134]
- Concave lens
- Lenses are classified by the curvature of the two optical surfaces. A lens is biconvex (or double convex, or just convex) if both surfaces are convex. If both surfaces have the same radius of curvature, the lens is equiconvex. A lens with two concave surfaces is biconcave (or just concave). If one of the surfaces is flat, the lens is plano-convex or plano-concave depending on the curvature of the other surface. A lens with one convex and one concave side is convex-concave or meniscus.
- Condensed matter physics
- Is the field of physics that deals with the macroscopic and microscopic physical properties of matter. In particular it is concerned with the "condensed" phases that appear whenever the number of constituents in a system is extremely large and the interactions between the constituents are strong.
- Confidence interval
- In statistics, a confidence interval or compatibility interval (CI) is a type of interval estimate, computed from the statistics of the observed data, that might contain the true value of an unknown population parameter. The interval has an associated confidence level that, loosely speaking, quantifies the level of confidence that the parameter lies in the interval. More strictly speaking, the confidence level represents the frequency (i.e. the proportion) of possible confidence intervals that contain the true value of the unknown population parameter. In other words, if confidence intervals are constructed using a given confidence level from an infinite number of independent sample statistics, the proportion of those intervals that contain the true value of the parameter will be equal to the confidence level.[135][136][137]
- Conjugate acid
- A conjugate acid, within the Brønsted–Lowry acid–base theory, is a species formed by the reception of a proton (H+) by a base—in other words, it is a base with a hydrogen ion added to it. On the other hand, a conjugate base is what is left over after an acid has donated a proton during a chemical reaction. Hence, a conjugate base is a species formed by the removal of a proton from an acid.[138] Because some acids are capable of releasing multiple protons, the conjugate base of an acid may itself be acidic.
- Conjugate base
- A conjugate acid, within the Brønsted–Lowry acid–base theory, is a species formed by the reception of a proton (H+) by a base—in other words, it is a base with a hydrogen ion added to it. On the other hand, a conjugate base is what is left over after an acid has donated a proton during a chemical reaction. Hence, a conjugate base is a species formed by the removal of a proton from an acid.[138] Because some acids are capable of releasing multiple protons, the conjugate base of an acid may itself be acidic.
- Conservation of energy
- In physics and chemistry, the law of conservation of energy states that the total energy of an isolated system remains constant; it is said to be conserved over time.[139] This law means that energy can neither be created nor destroyed; rather, it can only be transformed or transferred from one form to another.
- Conservation of mass
- The law of conservation of mass or principle of mass conservation states that for any system closed to all transfers of matter and energy, the mass of the system must remain constant over time, as system's mass cannot change, so quantity cannot be added nor removed. Hence, the quantity of mass is conserved over time.
- Continuity equation
- A continuity equation in physics is an equation that describes the transport of some quantity. It is particularly simple and powerful when applied to a conserved quantity, but it can be generalized to apply to any extensive quantity. Since mass, energy, momentum, electric charge and other natural quantities are conserved under their respective appropriate conditions, a variety of physical phenomena may be described using continuity equations.
- Continuum mechanics
- Is a branch of mechanics that deals with the mechanical behavior of materials modeled as a continuous mass rather than as discrete particles. The French mathematician Augustin-Louis Cauchy was the first to formulate such models in the 19th century.
- Control engineering
- Control engineering or control systems engineering is an engineering discipline that applies automatic control theory to design systems with desired behaviors in control environments.[140] The discipline of controls overlaps and is usually taught along with electrical engineering at many institutions around the world.[140] .
- Convex lens
- Lenses are classified by the curvature of the two optical surfaces. A lens is biconvex (or double convex, or just convex) if both surfaces are convex. If both surfaces have the same radius of curvature, the lens is equiconvex. A lens with two concave surfaces is biconcave (or just concave). If one of the surfaces is flat, the lens is plano-convex or plano-concave depending on the curvature of the other surface. A lens with one convex and one concave side is convex-concave or meniscus.
- Corrosion
- Is a natural process, which converts a refined metal to a more chemically-stable form, such as its oxide, hydroxide, or sulfide. It is the gradual destruction of materials (usually metals) by chemical and/or electrochemical reaction with their environment. Corrosion engineering is the field dedicated to controlling and stopping corrosion.
- Cosmic rays
- Cosmic rays are high-energy radiation, mainly originating outside the Solar System.[141]
- Coulomb
- The coulomb (symbol: C) is the International System of Units (SI) unit of electric charge. It is the charge (symbol: Q or q) transported by a constant current of one ampere in one second:
- Coulomb's law
- Coulomb's law, or Coulomb's inverse-square law, is a law of physics for quantifying Coulomb's force, or electrostatic force. Electrostatic force is the amount of force with which stationary, electrically charged particles either repel, or attract each other. This force and the law for quantifying it, represent one of the most basic forms of force used in the physical sciences, and were an essential basis to the study and development of the theory and field of classical electromagnetism. The law was first published in 1785 by French physicist Charles-Augustin de Coulomb.[143]
In its scalar form, the law is:
- ,
- Covalent bond
- A covalent bond, also called a molecular bond, is a chemical bond that involves the sharing of electron pairs between atoms.
- Crookes tube
- A type of vacuum tube that demonstrates cathode rays.
- Cryogenics
- The science of low temperatures.
- Crystallization
- Crystallization is the (natural or artificial) process by which a solid forms, where the atoms or molecules are highly organized into a structure known as a crystal. Some of the ways by which crystals form are precipitating from a solution, freezing, or more rarely deposition directly from a gas. Attributes of the resulting crystal depend largely on factors such as temperature, air pressure, and in the case of liquid crystals, time of fluid evaporation.
- Crystallography
- The study of crystals.
- Curvilinear motion
- Describes the motion of a moving particle that conforms to a known or fixed curve. The study of such motion involves the use of two co-ordinate systems, the first being planar motion and the latter being cylindrical motion.
- Cyclotron
- A cyclotron is a type of particle accelerator invented by Ernest O. Lawrence in 1929-1930 at the University of California, Berkeley,[144][145] and patented in 1932.[146][147] A cyclotron accelerates charged particles outwards from the center along a spiral path.[148][149] The particles are held to a spiral trajectory by a static magnetic field and accelerated by a rapidly varying (radio frequency) electric field. Lawrence was awarded the 1939 Nobel prize in physics for this invention.[149][150]
D[]
- Dalton's law
- In chemistry and physics, Dalton's law (also called Dalton's law of partial pressures) states that in a mixture of non-reacting gases, the total pressure exerted is equal to the sum of the partial pressures of the individual gases.[151]
- Damped vibration
- Any vibration with a force acting against it to lessen the vibration over time.
- Darcy–Weisbach equation
- An equation used in fluid mechanics to find the pressure change cause by friction within a pipe or conduit.
- DC motor
- An electrical motor driven by direct current.
- Decibel
- A logarithmic unit of ratios.
- Definite integral
- The integral of a function between an upper and lower limit.[152]
- Deflection
- Is the degree to which a structural element is displaced under a load. It may refer to an angle or a distance.
- Deformation (engineering)
- In materials science, deformation refers to any changes in the shape or size of an object due to
- an applied force (the deformation energy in this case is transferred through work) or
- a change in temperature (the deformation energy in this case is transferred through heat).
- Deformation (mechanics)
- Deformation in continuum mechanics is the transformation of a body from a reference configuration to a current configuration.[155] A configuration is a set containing the positions of all particles of the body. A deformation may be caused by external loads,[156] body forces (such as gravity or electromagnetic forces), or changes in temperature, moisture content, or chemical reactions, etc.
- Degrees of freedom
- The number of parameters required to define the motion of a dynamical system.
- Delta robot
- A tripod linkage, used to construct fast-acting manipulators with a wide range of movement.
- Delta-wye transformer
- A type of transformer used in three-phase power systems.
- De Moivre–Laplace theorem
- In probability theory, the de Moivre–Laplace theorem, which is a special case of the central limit theorem, states that the normal distribution may be used as an approximation to the binomial distribution under certain conditions. In particular, the theorem shows that the probability mass function of the random number of "successes" observed in a series of independent Bernoulli trials, each having probability of success (a binomial distribution with trials), converges to the probability density function of the normal distribution with mean and standard deviation, as grows large, assuming is not or .
- Density
- The density, or more precisely, the volumetric mass density, of a substance is its mass per unit volume. The symbol most often used for density is ρ (the lower case Greek letter rho), although the Latin letter D can also be used. Mathematically, density is defined as mass divided by volume:[157]
- Derivative
- The derivative of a function of a real variable measures the sensitivity to change of the function value (output value) with respect to a change in its argument (input value). Derivatives are a fundamental tool of calculus. For example, the derivative of the position of a moving object with respect to time is the object's velocity: this measures how quickly the position of the object changes when time advances.
- Design engineering
- .
- Dew point
- The pressure and temperature at which air is holding the maximum possible humidity.
- Diamagnetism
- Diamagnetic materials are repelled by a magnetic field; an applied magnetic field creates an induced magnetic field in them in the opposite direction, causing a repulsive force. In contrast, paramagnetic and ferromagnetic materials are attracted by a magnetic field. Diamagnetism is a quantum mechanical effect that occurs in all materials; when it is the only contribution to the magnetism, the material is called diamagnetic. In paramagnetic and ferromagnetic substances the weak diamagnetic force is overcome by the attractive force of magnetic dipoles in the material. The magnetic permeability of diamagnetic materials is less than μ0, the permeability of vacuum. In most materials diamagnetism is a weak effect which can only be detected by sensitive laboratory instruments, but a superconductor acts as a strong diamagnet because it repels a magnetic field entirely from its interior.
- Dielectric
- An insulator, a material that does not permit free flow of electricity.
- Differential pressure
- .
- Differential pulley
- A differential pulley, also called Weston differential pulley, or colloquially chain fall, is used to manually lift very heavy objects like car engines. It is operated by pulling upon the slack section of a continuous chain that wraps around pulleys. The relative size of two connected pulleys determines the maximum weight that can be lifted by hand. The load will remain in place (and not lower under the force of gravity) until the chain is pulled.[159]
- Differential signaling
- Is a method for electrically transmitting information using two complementary signals.
- Diffusion
- Is the net movement of molecules or atoms from a region of higher concentration (or high chemical potential) to a region of lower concentration (or low chemical potential).
- Dimensional analysis
- is the analysis of the relationships between different physical quantities by identifying their base quantities (such as length, mass, time, and electric charge) and units of measure (such as miles vs. kilometers, or pounds vs. kilograms) and tracking these dimensions as calculations or comparisons are performed. The conversion of units from one dimensional unit to another is often somewhat complex. Dimensional analysis, or more specifically the factor-label method, also known as the unit-factor method, is a widely used technique for such conversions using the rules of algebra.[160][161][162]
- Direct integration of a beam
- Direct integration is a structural analysis method for measuring internal shear, internal moment, rotation, and deflection of a beam.
For a beam with an applied weight , taking downward to be positive, the internal shear force is given by taking the negative integral of the weight:
- =
- .
E[]
- Economics
- The scientific study of the production, distribution and consumption of goods.
- Effusion
- In physics and chemistry, effusion is the process in which a gas escapes from a container through a hole of diameter considerably smaller than the mean free path of the molecules.[171]
- Elastic modulus
- The amount a material will deform per unit force.
- Elasticity
- In physics, elasticity is the ability of a body to resist a distorting influence and to return to its original size and shape when that influence or force is removed. Solid objects will deform when adequate forces are applied to them. If the material is elastic, the object will return to its initial shape and size when these forces are removed.
- Electric charge
- is the physical property of matter that causes it to experience a force when placed in an electromagnetic field. There are two types of electric charges; positive and negative (commonly carried by protons and electrons respectively). Like charges repel and unlike attract. An object with an absence of net charge is referred to as neutral. Early knowledge of how charged substances interact is now called classical electrodynamics, and is still accurate for problems that do not require consideration of quantum effects.
- Electric circuit
- Is an electrical network consisting of a closed loop, giving a return path for the current.
- Electric current
- Is a flow of electric charge.[172]: 2 In electric circuits this charge is often carried by moving electrons in a wire. It can also be carried by ions in an electrolyte, or by both ions and electrons such as in an ionised gas (plasma).[173] The SI unit for measuring an electric current is the ampere, which is the flow of electric charge across a surface at the rate of one coulomb per second. Electric current is measured using a device called an ammeter.[174]
- Electric displacement field
- In physics, the electric displacement field, denoted by D, is a vector field that appears in Maxwell's equations. It accounts for the effects of free and bound charge within materials. "D" stands for "displacement", as in the related concept of displacement current in dielectrics. In free space, the electric displacement field is equivalent to flux density, a concept that lends understanding to Gauss's law. In the International System of Units (SI), it is expressed in units of coulomb per meter squared (C⋅m−2).
- Electric generator
- In electricity generation, a generator,also called electric generator, electrical generator, and electromagnetic generator. is a device that converts motive power (mechanical energy) into electrical power for use in an external circuit. Sources of mechanical energy include steam turbines, gas turbines, water turbines, internal combustion engines and even hand cranks.
- Electric field
- Surrounds an electric charge, and exerts force on other charges in the field, attracting or repelling them.[175][176] Electric field is sometimes abbreviated as E-field.
- Electric field gradient
- In atomic, molecular, and solid-state physics, the electric field gradient (EFG) measures the rate of change of the electric field at an atomic nucleus generated by the electronic charge distribution and the other nuclei.
- Electric motor
- Is an electrical machine that converts electrical energy into mechanical energy. Most electric motors operate through the interaction between the motor's magnetic field and winding currents to generate force in the form of rotation. Electric motors can be powered by direct current (DC) sources, such as from batteries, motor vehicles or rectifiers, or by alternating current (AC) sources, such as a power grid, inverters or electrical generators. An electric generator is mechanically identical to an electric motor, but operates in the reverse direction, accepting mechanical energy (such as from flowing water) and converting this mechanical energy into electrical energy.
- Electric potential
- (Also called the electric field potential, potential drop or the electrostatic potential) is the amount of work needed to move a unit of positive charge from a reference point to a specific point inside the field without producing an acceleration. Typically, the reference point is the Earth or a point at infinity, although any point beyond the influence of the electric field charge can be used.
- Electrical potential energy
- Electric potential energy, or electrostatic potential energy, is a potential energy (measured in joules) that results from conservative Coulomb forces and is associated with the configuration of a particular set of point charges within a defined system. An object may have electric potential energy by virtue of two key elements: its own electric charge and its relative position to other electrically charged objects. The term "electric potential energy" is used to describe the potential energy in systems with time-variant electric fields, while the term "electrostatic potential energy" is used to describe the potential energy in systems with time-invariant electric fields.
- Electric power
- Is the rate, per unit time, at which electrical energy is transferred by an electric circuit. The SI unit of power is the watt, one joule per second.
- Electrical engineering
- Is a technical discipline concerned with the study, design and application of equipment, devices and systems which use electricity, electronics, and electromagnetism. It emerged as an identified activity in the latter half of the 19th century after commercialization of the electric telegraph, the telephone, and electrical power generation, distribution and use. .
- Electrical conductance
- The electrical resistance of an object is a measure of its opposition to the flow of electric current. The inverse quantity is electrical conductance, and is the ease with which an electric current passes. Electrical resistance shares some conceptual parallels with the notion of mechanical friction. The SI unit of electrical resistance is the ohm (Ω), while electrical conductance is measured in siemens (S).
- Electrical conductor
- Is an object or type of material that allows the flow of charge (electrical current) in one or more directions. Materials made of metal are common electrical conductors. Electrical current is generated by the flow of negatively charged electrons, positively charged holes, and positive or negative ions in some cases.
- Electrical impedance
- Is the measure of the opposition that a circuit presents to a current when a voltage is applied. The term complex impedance may be used interchangeably.
- Electrical insulator
- Is a material whose internal electric charges do not flow freely; very little electric current will flow through it under the influence of an electric field. This contrasts with other materials, semiconductors and conductors, which conduct electric current more easily. The property that distinguishes an insulator is its resistivity; insulators have higher resistivity than semiconductors or conductors.
- Electrical network
- Is an interconnection of electrical components (e.g., batteries, resistors, inductors, capacitors, switches, transistors) or a model of such an interconnection, consisting of electrical elements (e.g., voltage sources, current sources, resistances, inductances, capacitances). An electrical circuit is a network consisting of a closed loop, giving a return path for the current. Linear electrical networks, a special type consisting only of sources (voltage or current), linear lumped elements (resistors, capacitors, inductors), and linear distributed elements (transmission lines), have the property that signals are linearly superimposable. They are thus more easily analyzed, using powerful frequency domain methods such as Laplace transforms, to determine DC response, AC response, and transient response.
- Electrical resistance
- The electrical resistance of an object is a measure of its opposition to the flow of electric current. The inverse quantity is electrical conductance, and is the ease with which an electric current passes. Electrical resistance shares some conceptual parallels with the notion of mechanical friction. The SI unit of electrical resistance is the ohm (Ω), while electrical conductance is measured in siemens (S).
- Electricity
- Is the set of physical phenomena associated with the presence and motion of matter that has a property of electric charge. Electricity is related to magnetism, both being part of the phenomenon of electromagnetism, as described by Maxwell's equations. Various common phenomena are related to electricity, including lightning, static electricity, electric heating, electric discharges and many others.
- Electrodynamics
- In physics, the phenomena associated with moving electric charges, and their interaction with electric and magnetic fields; the study of these phenomena.[177]
- Electromagnet
- Is a type of magnet in which the magnetic field is produced by an electric current. Electromagnets usually consist of wire wound into a coil. A current through the wire creates a magnetic field which is concentrated in the hole, denoting the centre of the coil. The magnetic field disappears when the current is turned off. The wire turns are often wound around a magnetic core made from a ferromagnetic or ferrimagnetic material such as iron; the magnetic core concentrates the magnetic flux and makes a more powerful magnet.
- Electromagnetic field
- An electromagnetic field (also EM field) is a classical (i.e. non-quantum) field produced by accelerating electric charges.[178] It is the field described by classical electrodynamics and is the classical counterpart to the quantized electromagnetic field tensor in quantum electrodynamics. The electromagnetic field propagates at the speed of light (in fact, this field can be identified as light) and interacts with charges and currents. Its quantum counterpart is one of the four fundamental forces of nature (the others are gravitation, weak interaction and strong interaction.)
- Electromagnetic radiation
- In physics, electromagnetic radiation (EM radiation or EMR) refers to the waves (or their quanta, photons) of the electromagnetic field, propagating (radiating) through space, carrying electromagnetic radiant energy.[179] It includes radio waves, microwaves, infrared, (visible) light, ultraviolet, X-rays, and gamma rays.[180]
- Electromechanics
- Electromechanics[181][182][183][184] combines processes and procedures drawn from electrical engineering and mechanical engineering. Electromechanics focuses on the interaction of electrical and mechanical systems as a whole and how the two systems interact with each other. This process is especially prominent in systems such as those of DC or AC rotating electrical machines which can be designed and operated to generate power from a mechanical process (generator) or used to power a mechanical effect (motor). Electrical engineering in this context also encompasses electronics engineering.
- Electron
- Is a subatomic particle, symbol
e−
or
β−
, whose electric charge is negative one elementary charge.[185] Electrons belong to the first generation of the lepton particle family,[186] and are generally thought to be elementary particles because they have no known components or substructure.[187] The electron has a mass that is approximately 1/1836 that of the proton.[188] Quantum mechanical properties of the electron include an intrinsic angular momentum (spin) of a half-integer value, expressed in units of the reduced Planck constant, ħ. Being fermions, no two electrons can occupy the same quantum state, in accordance with the Pauli exclusion principle.[186] Like all elementary particles, electrons exhibit properties of both particles and waves: they can collide with other particles and can be diffracted like light. The wave properties of electrons are easier to observe with experiments than those of other particles like neutrons and protons because electrons have a lower mass and hence a longer de Broglie wavelength for a given energy. - Electronvolt
- In physics, an electronvolt (symbol eV, also written electron-volt and electron volt) is the amount of kinetic energy gained by a single electron accelerating from rest through an electric potential difference of one volt in vacuum. When used as a unit of energy, the numerical value of 1 eV in joules (symbol J) is equivalent to the numerical value of the charge of an electron in coulombs (symbol C). Under the 2019 redefinition of the SI base units, this sets 1 eV equal to the exact value 1.602176634×10−19 J.[189]
- Electron pair
- In chemistry, an electron pair, or Lewis pair, consists of two electrons that occupy the same molecular orbital but have opposite spins. Gilbert N. Lewis introduced the concepts of both the electron pair and the covalent bond in a landmark paper he published in 1916.[190]
- Electronegativity
- Symbolized as χ, is the measurement of the tendency of an atom to attract a shared pair of electrons (or electron density).[191] An atom's electronegativity is affected by both its atomic number and the distance at which its valence electrons reside from the charged nucleus. The higher the associated electronegativity, the more an atom or a substituent group attracts electrons.
- Electronics
- Comprises the physics, engineering, technology and applications that deal with the emission, flow and control of electrons in vacuum and matter.[192] It uses active devices to control electron flow by amplification and rectification, which distinguishes it from classical electrical engineering which uses passive effects such as resistance, capacitance and inductance to control current flow.
- Elemental analysis
- Is a process where a sample of some material (e.g., soil, waste or drinking water, bodily fluids, minerals, chemical compounds) is analyzed for its elemental and sometimes isotopic composition.[citation needed] Elemental analysis can be qualitative (determining what elements are present), and it can be quantitative (determining how much of each are present). Elemental analysis falls within the ambit of analytical chemistry, the set of instruments involved in deciphering the chemical nature of our world.
- Endothermic process
- Is any process with an increase in the enthalpy H (or internal energy U) of the system.[193] In such a process, a closed system usually absorbs thermal energy from its surroundings, which is heat transfer into the system. It may be a chemical process, such as dissolving ammonium nitrate in water, or a physical process, such as the melting of ice cubes.
- Energy
- In physics, energy is the quantitative property that must be transferred to an object in order to perform work on, or to heat, the object.[note 1] Energy is a conserved quantity; the law of conservation of energy states that energy can be converted in form, but not created or destroyed. The SI unit of energy is the joule, which is the energy transferred to an object by the work of moving it a distance of 1 metre against a force of 1 newton.
- Engine
- An engine or motor is a machine designed to convert one form of energy into mechanical energy.[194][195] Heat engines convert heat into work via various thermodynamic processes. The internal combustion engine is perhaps the most common example of a heat engine, in which heat from the combustion of a fuel causes rapid pressurisation of the gaseous combustion products in the combustion chamber, causing them to expand and drive a piston, which turns a crankshaft. Electric motors convert electrical energy into mechanical motion, pneumatic motors use compressed air, and clockwork motors in wind-up toys use elastic energy. In biological systems, molecular motors, like myosins in muscles, use chemical energy to create forces and ultimately motion.
- Engineering
- Is the use of scientific principles to design and build machines, structures, and other items, including bridges, tunnels, roads, vehicles, and buildings.[196] The discipline of engineering encompasses a broad range of more specialized fields of engineering, each with a more specific emphasis on particular areas of applied mathematics, applied science, and types of application. The term engineering is derived from the Latin ingenium, meaning "cleverness" and ingeniare, meaning "to contrive, devise".[197]
- Engineering economics
- Engineering economics, previously known as engineering economy, is a subset of economics concerned with the use and "...application of economic principles"[198] in the analysis of engineering decisions.[199] As a discipline, it is focused on the branch of economics known as microeconomics in that it studies the behavior of individuals and firms in making decisions regarding the allocation of limited resources. Thus, it focuses on the decision making process, its context and environment.[198] It is pragmatic by nature, integrating economic theory with engineering practice.[198] But, it is also a simplified application of microeconomic theory in that it assumes elements such as price determination, competition and demand/supply to be fixed inputs from other sources.[198] As a discipline though, it is closely related to others such as statistics, mathematics and cost accounting.[198] It draws upon the logical framework of economics but adds to that the analytical power of mathematics and statistics.[198]
- Engineering ethics
- Is the field of system of moral principles that apply to the practice of engineering. The field examines and sets the obligations by engineers to society, to their clients, and to the profession. As a scholarly discipline, it is closely related to subjects such as the philosophy of science, the philosophy of engineering, and the ethics of technology.
- Environmental engineering
- Is a job type that is a professional engineering discipline and takes from broad scientific topics like chemistry, biology, ecology, geology, hydraulics, hydrology, microbiology, and mathematics to create solutions that will protect and also improve the health of living organisms and improve the quality of the environment.[200][201] Environmental engineering is a sub-discipline of civil engineering and chemical engineering.
- Engineering physics
- Or engineering science, refers to the study of the combined disciplines of physics, mathematics, chemistry, biology, and engineering, particularly computer, nuclear, electrical, electronic, aerospace, materials or mechanical engineering. By focusing on the scientific method as a rigorous basis, it seeks ways to apply, design, and develop new solutions in engineering.[202][203][204][205]
- Enzyme
- Enzymes are proteins that act as biological catalysts (biocatalysts). Catalysts accelerate chemical reactions. The molecules upon which enzymes may act are called substrates, and the enzyme converts the substrates into different molecules known as products. Almost all metabolic processes in the cell need enzyme catalysis in order to occur at rates fast enough to sustain life.[206]: 8.1
- Escape velocity
- The minimum velocity at which an object can escape a gravitation field.
- Estimator
- In statistics, an estimator is a rule for calculating an estimate of a given quantity based on observed data: thus the rule (the estimator), the quantity of interest (the estimand) and its result (the estimate) are distinguished.[207] For example, the sample mean is a commonly used estimator of the population mean. There are point and interval estimators. The point estimators yield single-valued results, although this includes the possibility of single vector-valued results and results that can be expressed as a single function. This is in contrast to an interval estimator, where the result would be a range of plausible values (or vectors or functions).
- Euler–Bernoulli beam theory
- Euler–Bernoulli beam theory (also known as engineer's beam theory or classical beam theory)[208] is a simplification of the linear theory of elasticity which provides a means of calculating the load-carrying and deflection characteristics of beams. It covers the case for small deflections of a beam that are subjected to lateral loads only. It is thus a special case of Timoshenko beam theory. It was first enunciated circa 1750,[209] but was not applied on a large scale until the development of the Eiffel Tower and the Ferris wheel in the late 19th century. Following these successful demonstrations, it quickly became a cornerstone of engineering and an enabler of the Second Industrial Revolution. Additional mathematical models have been developed such as plate theory, but the simplicity of beam theory makes it an important tool in the sciences, especially structural and mechanical engineering.
- Exothermic process
- In thermodynamics, the term exothermic process (exo- : "outside") describes a process or reaction that releases energy from the system to its surroundings, usually in the form of heat, but also in a form of light (e.g. a spark, flame, or flash), electricity (e.g. a battery), or sound (e.g. explosion heard when burning hydrogen). Its etymology stems from the Greek prefix έξω (exō, which means "outwards") and the Greek word θερμικός (thermikόs, which means "thermal").[210]
F[]
- Factor of safety
- (FoS), also known as (and used interchangeably with) safety factor (SF), expresses how much stronger a system is than it needs to be for an intended load.
- Falling bodies
- .
- Farad
- [211] The farad (symbol: F) is the SI derived unit of electrical capacitance, the ability of a body to store an electrical charge. It is named after the English physicist Michael Faraday.
- Faraday constant
- Denoted by the symbol F and sometimes stylized as ℱ, is named after Michael Faraday. In physics and chemistry, this constant represents the magnitude of electric charge per mole of electrons.[212] It has the value
- 96485.33212... C mol−1.[213]
- Fermat's principle
- In optics, Fermat's principle, or the principle of least time, named after French mathematician Pierre de Fermat, is the principle that the path taken between two points by a ray of light is the path that can be traversed in the least time. This principle is sometimes taken as the definition of a ray of light.[216] However, this version of the principle is not general; a more modern statement of the principle is that rays of light traverse the path of stationary optical length with respect to variations of the path.[217] In other words, a ray of light prefers the path such that there are other paths, arbitrarily nearby on either side, along which the ray would take almost exactly the same time to traverse.
- Fick's laws of diffusion
- Describe diffusion and were derived by Adolf Fick in 1855. They can be used to solve for the diffusion coefficient, D. Fick's first law can be used to derive his second law which in turn is identical to the diffusion equation.
- Finite element method
- (FEM), is the most widely used method for solving problems of engineering and mathematical models. Typical problem areas of interest include the traditional fields of structural analysis, heat transfer, fluid flow, mass transport, and electromagnetic potential. The FEM is a particular numerical method for solving partial differential equations in two or three space variables (i.e., some boundary value problems). To solve a problem, the FEM subdivides a large system into smaller, simpler parts that are called finite elements. This is achieved by a particular space discretization in the space dimensions, which is implemented by the construction of a mesh of the object: the numerical domain for the solution, which has a finite number of points. The finite element method formulation of a boundary value problem finally results in a system of algebraic equations. The method approximates the unknown function over the domain.[218] The simple equations that model these finite elements are then assembled into a larger system of equations that models the entire problem. The FEM then uses variational methods from the calculus of variations to approximate a solution by minimizing an associated error function.
- FIRST
- For Inspiration and Recognition of Science and Technology – is an organization founded by inventor Dean Kamen in 1989 to develop ways to inspire students in engineering and technology fields.
- Fission
- In nuclear physics and nuclear chemistry, nuclear fission is a nuclear reaction or a radioactive decay process in which the nucleus of an atom splits into two or more smaller, lighter nuclei. The fission process often produces gamma photons, and releases a very large amount of energy even by the energetic standards of radioactive decay.
- Flow velocity
- In continuum mechanics the flow velocity in fluid dynamics, also macroscopic velocity[219][220] in statistical mechanics, or drift velocity in electromagnetism, is a vector field used to mathematically describe the motion of a continuum. The length of the flow velocity vector is the flow speed and is a scalar. It is also called velocity field; when evaluated along a line, it is called a velocity profile (as in, e.g., law of the wall).
- Fluid
- In physics, a fluid is a substance that continually deforms (flows) under an applied shear stress, or external force. Fluids are a phase of matter and include liquids, gases and plasmas. They are substances with zero shear modulus, or, in simpler terms, substances which cannot resist any shear force applied to them.
- Fluid dynamics
- In physics and engineering, fluid dynamics is a subdiscipline of fluid mechanics that describes the flow of fluids—liquids and gases. It has several subdisciplines, including aerodynamics (the study of air and other gases in motion) and hydrodynamics (the study of liquids in motion).
- Fluid mechanics
- Is the branch of physics concerned with the mechanics of fluids (liquids, gases, and plasmas) and the forces on them.[221] It has applications in a wide range of disciplines, including mechanical, civil, chemical and biomedical engineering, geophysics, oceanography, meteorology, astrophysics, and biology.
- Fluid statics
- Fluid statics, or hydrostatics, is the branch of fluid mechanics that studies "fluids at rest and the pressure in a fluid or exerted by a fluid on an immersed body".[222]
- Flywheel
- Is a mechanical device specifically designed to use the conservation of angular momentum so as to efficiently store rotational energy; a form of kinetic energy proportional to the product of its moment of inertia and the square of its rotational speed. In particular, if we assume the flywheel's moment of inertia to be constant (i.e., a flywheel with fixed mass and second moment of area revolving about some fixed axis) then the stored (rotational) energy is directly associated with the square of its rotational speed.
- Focus
- In geometrical optics, a focus, also called an image point, is the point where light rays originating from a point on the object converge.[223] Although the focus is conceptually a point, physically the focus has a spatial extent, called the blur circle. This non-ideal focusing may be caused by aberrations of the imaging optics. In the absence of significant aberrations, the smallest possible blur circle is the Airy disc, which is caused by diffraction from the optical system's aperture. Aberrations tend worsen as the aperture diameter increases, while the Airy circle is smallest for large apertures.
- Foot-pound
- The foot-pound force (symbol: ft⋅lbf,[224] ft⋅lbf,[225] or ft⋅lb [226]) is a unit of work or energy in the engineering and gravitational systems in United States customary and imperial units of measure. It is the energy transferred upon applying a force of one pound-force (lbf) through a linear displacement of one foot. The corresponding SI unit is the joule.
- Fracture toughness
- In materials science, fracture toughness is the critical stress intensity factor of a sharp crack where propagation of the crack suddenly becomes rapid and unlimited. A component's thickness affects the constraint conditions at the tip of a crack with thin components having plane stress conditions and thick components having plane strain conditions. Plane strain conditions give the lowest fracture toughness value which is a material property. The critical value of stress intensity factor in mode I loading measured under plane strain conditions is known as the plane strain fracture toughness, denoted .[227] When a test fails to meet the thickness and other test requirements that are in place to ensure plane strain conditions, the fracture toughness value produced is given the designation . Fracture toughness is a quantitative way of expressing a material's resistance to crack propagation and standard values for a given material are generally available.
- Fraunhofer lines
- In physics and optics, the Fraunhofer lines are a set of spectral absorption lines named after the German physicist Joseph von Fraunhofer (1787–1826). The lines were originally observed as dark features (absorption lines) in the optical spectrum of the Sun.
- Free fall
- In Newtonian physics, free fall is any motion of a body where gravity is the only force acting upon it. In the context of general relativity, where gravitation is reduced to a space-time curvature, a body in free fall has no force acting on it.
- Frequency modulation
- Frequency modulation (FM) is the encoding of information in a carrier wave by varying the instantaneous frequency of the wave. The technology is used in telecommunications, radio broadcasting, signal processing, and computing.
- Freezing point
- The melting point (or, rarely, liquefaction point) of a substance is the temperature at which it changes state from solid to liquid. At the melting point the solid and liquid phase exist in equilibrium. The melting point of a substance depends on pressure and is usually specified at a standard pressure such as 1 atmosphere or 100 kPa. When considered as the temperature of the reverse change from liquid to solid, it is referred to as the freezing point or crystallization point. Because of the ability of substances to supercool, the freezing point can easily appear to be below its actual value. When the "characteristic freezing point" of a substance is determined, in fact the actual methodology is almost always "the principle of observing the disappearance rather than the formation of ice, that is, the melting point.[228]
- Friction
- Is the force resisting the relative motion of solid surfaces, fluid layers, and material elements sliding against each other.[229] There are several types of friction:
- Dry friction is a force that opposes the relative lateral motion of two solid surfaces in contact. Dry friction is subdivided into static friction ("stiction") between non-moving surfaces, and kinetic friction between moving surfaces. With the exception of atomic or molecular friction, dry friction generally arises from the interaction of surface features, known as asperities (see Figure 1).
- Fluid friction describes the friction between layers of a viscous fluid that are moving relative to each other.[230][231]
- Lubricated friction is a case of fluid friction where a lubricant fluid separates two solid surfaces.[232][233][234]
- Skin friction is a component of drag, the force resisting the motion of a fluid across the surface of a body.
- Internal friction is the force resisting motion between the elements making up a solid material while it undergoes deformation.[231]
- Function
- In mathematics, a function[note 2] is a binary relation between two sets that associates every element of the first set to exactly one element of the second set. Typical examples are functions from integers to integers, or from the real numbers to real numbers.
- Fundamental frequency
- The fundamental frequency, often referred to simply as the fundamental, is defined as the lowest frequency of a periodic waveform. In music, the fundamental is the musical pitch of a note that is perceived as the lowest partial present. In terms of a superposition of sinusoids, the fundamental frequency is the lowest frequency sinusoidal in the sum of harmonically related frequencies, or the frequency of the difference between adjacent frequencies. In some contexts, the fundamental is usually abbreviated as f0, indicating the lowest frequency counting from zero.[235][236][237] In other contexts, it is more common to abbreviate it as f1, the first harmonic.[238][239][240][241][242] (The second harmonic is then f2 = 2⋅f1, etc. In this context, the zeroth harmonic would be 0 Hz.)
- Fundamental interaction
- In physics, the fundamental interactions, also known as fundamental forces, are the interactions that do not appear to be reducible to more basic interactions. There are four fundamental interactions known to exist: the gravitational and electromagnetic interactions, which produce significant long-range forces whose effects can be seen directly in everyday life, and the strong and weak interactions, which produce forces at minuscule, subatomic distances and govern nuclear interactions. Some scientists hypothesize that a fifth force might exist, but these hypotheses remain speculative.[243][244][245]
- Fundamental theorem of calculus
- Is a theorem that links the concept of differentiating a function with the concept of integrating a function.
- Fundamentals of Engineering Examination (US)
- The Fundamentals of Engineering (FE) exam, also referred to as the Engineer in Training (EIT) exam, and formerly in some states as the Engineering Intern (EI) exam, is the first of two examinations that engineers must pass in order to be licensed as a Professional Engineer in the United States. The second examination is Principles and Practice of Engineering Examination. The FE exam is open to anyone with a degree in engineering or a related field, or currently enrolled in the last year of an ABET-accredited engineering degree program. Some state licensure boards permit students to take it prior to their final year, and numerous states allow those who have never attended an approved program to take the exam if they have a state-determined number of years of work experience in engineering. Some states allow those with ABET-accredited "Engineering Technology" or "ETAC" degrees to take the examination. The state of Michigan has no admission pre-requisites for the FE.[246] The exam is administered by the National Council of Examiners for Engineering and Surveying (NCEES).
G[]
- Galvanic cell
- A galvanic cell or voltaic cell, named after Luigi Galvani or Alessandro Volta, respectively, is an electrochemical cell that derives electrical energy from spontaneous redox reactions taking place within the cell. It generally consists of two different metals immersed in electrolytes, or of individual half-cells with different metals and their ions in solution connected by a salt bridge or separated by a porous membrane. Volta was the inventor of the voltaic pile, the first electrical battery. In common usage, the word "battery" has come to include a single galvanic cell, but a battery properly consists of multiple cells.[247]
- Gamma rays
- A gamma ray, or gamma radiation (symbol γ or ), is a penetrating form of electromagnetic radiation arising from the radioactive decay of atomic nuclei. It consists of the shortest wavelength electromagnetic waves and so imparts the highest photon energy.
- Gas
- Is one of the four fundamental states of matter (the others being solid, liquid, and plasma). A pure gas may be made up of individual atoms (e.g. a noble gas like neon), elemental molecules made from one type of atom (e.g. oxygen), or compound molecules made from a variety of atoms (e.g. carbon dioxide). A gas mixture, such as air, contains a variety of pure gases. What distinguishes a gas from liquids and solids is the vast separation of the individual gas particles.
- Gauge pressure
- Is zero-referenced against ambient air pressure, so it is equal to absolute pressure minus atmospheric pressure.
- Geiger counter
- Is an instrument used for detecting and measuring ionizing radiation. Also known as a Geiger–Muller counter (or Geiger–Müller counter), it is widely used in applications such as radiation dosimetry, radiological protection, experimental physics, and the nuclear industry.
- General relativity
- General relativity, also known as the general theory of relativity, is the geometric theory of gravitation published by Albert Einstein in 1915 and is the current description of gravitation in modern physics. General relativity generalizes special relativity and refines Newton's law of universal gravitation, providing a unified description of gravity as a geometric property of space and time or four-dimensional spacetime. In particular, the curvature of spacetime is directly related to the energy and momentum of whatever matter and radiation are present. The relation is specified by the Einstein field equations, a system of partial differential equations.
- Geometric mean
- In mathematics, the geometric mean is a mean or average, which indicates the central tendency or typical value of a set of numbers by using the product of their values (as opposed to the arithmetic mean which uses their sum). The geometric mean is defined as the nth root of the product of n numbers, i.e., for a set of numbers x1, x2, ..., xn, the geometric mean is defined as
- ,
- Rate1 is the rate of effusion for the first gas. (volume or number of moles per unit time).
- Rate2 is the rate of effusion for the second gas.
- M1 is the molar mass of gas 1
- M2 is the molar mass of gas 2.
H[]
- Half-life
- The period at which one-half of a quantity of an unstable isotope has decayed into other elements; the time at which half of a substance has diffused out of or otherwise reacted in a system.
- Haptic
- Tactile feedback technology using the operator's sense of touch. Also sometimes applied to robot manipulators with their own touch sensitivity.
- Hardness
- Is a measure of the resistance to localized plastic deformation induced by either mechanical indentation or abrasion. Some materials (e.g. metals) are harder than others (e.g. plastics, wood). Macroscopic hardness is generally characterized by strong intermolecular bonds, but the behavior of solid materials under force is complex; therefore, there are different measurements of hardness: scratch hardness, indentation hardness, and rebound hardness. Hardness is dependent on ductility, elastic stiffness, plasticity, strain, strength, toughness, viscoelasticity, and viscosity.
- Harmonic mean
- In mathematics, the harmonic mean (sometimes called the subcontrary mean) is one of several kinds of average, and in particular, one of the Pythagorean means. Typically, it is appropriate for situations when the average of rates is desired.
The harmonic mean can be expressed as the reciprocal of the arithmetic mean of the reciprocals of the given set of observations. As a simple example, the harmonic mean of 1, 4, and 4 is
I[]
- Ice point
- The freezing point of pure water at one atmosphere; 0°C (32°F).[277]
- Ideal gas
- A model for gases that ignores inter-molecular forces. Most gases are approximately ideal at some high temperature and low pressure.
- Ideal gas constant
- The constant in the gas law that relates pressure, volume and temperature.
- Ideal gas law
- Also called the general gas equation, is the equation of state of a hypothetical ideal gas. It is a good approximation of the behavior of many gases under many conditions, although it has several limitations. It was first stated by Benoît Paul Émile Clapeyron in 1834 as a combination of the empirical Boyle's law, Charles's law, Avogadro's law, and Gay-Lussac's law.[278] The ideal gas law is often written in an empirical form:
- Identity
- In mathematics, an identity is an equality relating one mathematical expression A to another mathematical expression B, such that A and B (which might contain some variables) produce the same value for all values of the variables within a certain range of validity.[281][282] In other words, A = B is an identity if A and B define the same functions, and an identity is an equality between functions that are differently defined. For example, and are identities.[282] Identities are sometimes indicated by the triple bar symbol ≡ instead of =, the equals sign.[283]
- Impedance (electrical)
- In electrical engineering, electrical impedance is the measure of the opposition that a circuit presents to a current when a voltage is applied.
- Inclined plane
- Also known as a ramp, is a flat supporting surface tilted at an angle, with one end higher than the other, used as an aid for raising or lowering a load.[284][285][286] The inclined plane is one of the six classical simple machines defined by Renaissance scientists. Inclined planes are widely used to move heavy loads over vertical obstacles; examples vary from a ramp used to load goods into a truck, to a person walking up a pedestrian ramp, to an automobile or railroad train climbing a grade.[286]
- Indefinite integral
- A function whose derivative is a given function; an antiderivative.[287]
- Inductance
- In electromagnetism and electronics, inductance is the tendency of an electrical conductor to oppose a change in the electric current flowing through it. The flow of electric current creates a magnetic field around the conductor. The field strength depends on the magnitude of the current, and follows any changes in current. From Faraday's law of induction, any change in magnetic field through a circuit induces an electromotive force (EMF) (voltage) in the conductors, a process known as electromagnetic induction. This induced voltage created by the changing current has the effect of opposing the change in current. This is stated by Lenz's law, and the voltage is called back EMF. Inductance is defined as the ratio of the induced voltage to the rate of change of current causing it. It is a proportionality factor that depends on the geometry of circuit conductors and the magnetic permeability of nearby materials.[288] An electronic component designed to add inductance to a circuit is called an inductor. It typically consists of a coil or helix of wire.
- Inductor
- An inductor, also called a coil, choke, or reactor, is a passive two-terminal electrical component that stores energy in a magnetic field when electric current flows through it.[289] An inductor typically consists of an insulated wire wound into a coil.
- Industrial engineering
- Is an engineering profession that is concerned with the optimization of complex processes, systems, or organizations by developing, improving and implementing integrated systems of people, money, knowledge, information and equipment. Industrial engineers use specialized knowledge and skills in the mathematical, physical and social sciences, together with the principles and methods of engineering analysis and design, to specify, predict, and evaluate the results obtained from systems and processes.[290] From these results, they are able to create new systems, processes or situations for the useful coordination of labour, materials and machines and also improve the quality and productivity of systems, physical or social.[291]
- Inertia
- Is the resistance of any physical object to any change in its velocity. This includes changes to the object's speed, or direction of motion. An aspect of this property is the tendency of objects to keep moving in a straight line at a constant speed, when no forces act upon them.
- Infrasound
- Infrasound, sometimes referred to as low-frequency sound, describes sound waves with a frequency below the lower limit of audibility (generally 20 Hz). Hearing becomes gradually less sensitive as frequency decreases, so for humans to perceive infrasound, the sound pressure must be sufficiently high. The ear is the primary organ for sensing low sound, but at higher intensities it is possible to feel infrasound vibrations in various parts of the body.
- Integral
- In mathematics, an integral assigns numbers to functions in a way that describes displacement, area, volume, and other concepts that arise by combining infinitesimal data. The process of finding integrals is called integration. Along with differentiation, integration is a fundamental operation of calculus,[b] and serves as a tool to solve problems in mathematics and physics involving the area of an arbitrary shape, the length of a curve, and the volume of a solid, among others.
- Integral transform
- In mathematics, an integral transform maps a function from its original function space into another function space via integration, where some of the properties of the original function might be more easily characterized and manipulated than in the original function space. The transformed function can generally be mapped back to the original function space using the inverse transform.
- International System of Units
- The International System of Units (SI, abbreviated from the French Système international (d'unités)) is the modern form of the metric system. It is the only system of measurement with an official status in nearly every country in the world. It comprises a coherent system of units of measurement starting with seven base units, which are the second (the unit of time with the symbol s), metre (length, m), kilogram (mass, kg), ampere (electric current, A), kelvin (thermodynamic temperature, K), mole (amount of substance, mol), and candela (luminous intensity, cd). The system allows for an unlimited number of additional units, called derived units, which can always be represented as products of powers of the base units.[Note 1] Twenty-two derived units have been provided with special names and symbols.[Note 2] The seven base units and the 22 derived units with special names and symbols may be used in combination to express other derived units,[Note 3] which are adopted to facilitate measurement of diverse quantities. The SI system also provides twenty prefixes to the unit names and unit symbols that may be used when specifying power-of-ten (i.e. decimal) multiples and sub-multiples of SI units. The SI is intended to be an evolving system; units and prefixes are created and unit definitions are modified through international agreement as the technology of measurement progresses and the precision of measurements improves.
- Interval estimation
- In statistics, interval estimation is the use of sample data to calculate an interval of possible values of an unknown population parameter; this is in contrast to point estimation, which gives a single value. Jerzy Neyman (1937) identified interval estimation ("estimation by interval") as distinct from point estimation ("estimation by unique estimate"). In doing so, he recognized that then-recent work quoting results in the form of an estimate plus-or-minus a standard deviation indicated that interval estimation was actually the problem statisticians really had in mind.
- Inorganic chemistry
- Deals with synthesis and behavior of inorganic and organometallic compounds. This field covers chemical compounds that are not carbon-based, which are the subjects of organic chemistry. The distinction between the two disciplines is far from absolute, as there is much overlap in the subdiscipline of organometallic chemistry. It has applications in every aspect of the chemical industry, including catalysis, materials science, pigments, surfactants, coatings, medications, fuels, and agriculture.[292]
- Ion
- Is a particle, atom or molecule with a net electrical charge. The charge of the electron is considered negative by convention. The negative charge of an ion is equal and opposite to charged proton(s) considered positive by convention. The net charge of an ion is non-zero due to its total number of electrons being unequal to its total number of protons.
- Ionic bonding
- Is a type of chemical bonding that involves the electrostatic attraction between oppositely charged ions, or between two atoms with sharply different electronegativities,[293] and is the primary interaction occurring in ionic compounds. It is one of the main types of bonding along with covalent bonding and metallic bonding. Ions are atoms (or groups of atoms) with an electrostatic charge. Atoms that gain electrons make negatively charged ions (called anions). Atoms that lose electrons make positively charged ions (called cations). This transfer of electrons is known as electrovalence in contrast to covalence. In the simplest case, the cation is a metal atom and the anion is a nonmetal atom, but these ions can be of a more complex nature, e.g. molecular ions like NH+
4 or SO2−
4. In simpler words, an ionic bond results from the transfer of electrons from a metal to a non-metal in order to obtain a full valence shell for both atoms. - Ionization
- Ionization or ionisation is the process by which an atom or a molecule acquires a negative or positive charge by gaining or losing electrons, often in conjunction with other chemical changes. The resulting electrically charged atom or molecule is called an ion. Ionization can result from the loss of an electron after collisions with subatomic particles, collisions with other atoms, molecules and ions, or through the interaction with electromagnetic radiation. Heterolytic bond cleavage and heterolytic substitution reactions can result in the formation of ion pairs. Ionization can occur through radioactive decay by the internal conversion process, in which an excited nucleus transfers its energy to one of the inner-shell electrons causing it to be ejected.
- Isotope
- Isotopes are variants of a particular chemical element which differ in neutron number, and consequently in nucleon number. All isotopes of a given element have the same number of protons but different numbers of neutrons in each atom.[294]
J[]
- J/psi meson
- The
J/ψ
(J/psi) meson /ˈdʒeɪ ˈsaɪ ˈmiːzɒn/ or psion[295] is a subatomic particle, a flavor-neutral meson consisting of a charm quark and a charm antiquark. Mesons formed by a bound state of a charm quark and a charm anti-quark are generally known as "charmonium". The
J/ψ
is the most common form of charmonium, due to its spin of 1 and its low rest mass. The
J/ψ
has a rest mass of 3.0969 GeV/c2, just above that of the
η
c (2.9836 GeV/c2), and a mean lifetime of 7.2×10−21 s. This lifetime was about a thousand times longer than expected.[296] - Joule
- The SI unit of energy.The joule, (symbol: J), is a derived unit of energy in the International System of Units.[297] It is equal to the energy transferred to (or work done on) an object when a force of one newton acts on that object in the direction of the force's motion through a distance of one metre (1 newton metre or N⋅m). It is also the energy dissipated as heat when an electric current of one ampere passes through a resistance of one ohm for one second. It is named after the English physicist James Prescott Joule (1818–1889).[298][299][300] gh a conductor produces heat.
- Joule heating
- Also known as resistive, resistance, or Ohmic heating, is the process by which the passage of an electric current through a conductor produces heat.
K[]
- Kalman filter
- In statistics and control theory, Kalman filtering, also known as linear quadratic estimation (LQE), is an algorithm that uses a series of measurements observed over time, containing statistical noise and other inaccuracies, and produces estimates of unknown variables that tend to be more accurate than those based on a single measurement alone, by estimating a joint probability distribution over the variables for each timeframe. The Kalman filter has numerous applications in technology.
- Kelvin
- Is an absolute thermodynamic temperature scale using as its null point absolute zero, the temperature at which all thermal motion ceases in the classical description of thermodynamics. The kelvin (symbol: K) is the base unit of temperature in the International System of Units (SI).
- Kelvin–Planck statement
- (Or the Heat Engine Statement), of the second law of thermodynamics states that it is impossible to devise a cyclically operating heat engine, the effect of which is to absorb energy in the form of heat from a single thermal reservoir and to deliver an equivalent amount of work.[301] This implies that it is impossible to build a heat engine that has 100% thermal efficiency.[302]
- Kinematics
- Is a branch of classical mechanics that describes the motion of points, bodies (objects), and systems of bodies (groups of objects) without considering the forces that caused the motion.[303][304][305]
L[]
- Laminar flow
- In fluid dynamics, laminar flow is characterized by fluid particles following smooth paths in layers, with each layer moving smoothly past the adjacent layers with little or no mixing.[306] At low velocities, the fluid tends to flow without lateral mixing, and adjacent layers slide past one another like playing cards. There are no cross-currents perpendicular to the direction of flow, nor eddies or swirls of fluids.[307] In laminar flow, the motion of the particles of the fluid is very orderly with particles close to a solid surface moving in straight lines parallel to that surface.[308] Laminar flow is a flow regime characterized by high momentum diffusion and low momentum convection.
- Laplace transform
- In mathematics, the Laplace transform, named after its inventor Pierre-Simon Laplace (/ləˈplɑːs/), is an integral transform that converts a function of a real variable (often time) to a function of a complex variable (complex frequency). The transform has many applications in science and engineering because it is a tool for solving differential equations. In particular, it transforms differential equations into algebraic equations and convolution into multiplication.[309][310][311]
- LC circuit
- A circuit consisting entirely of inductors (L) and capacitors (C).
- Le Chatelier's principle
- Le Chatelier's principle, also called Chatelier's principle, is a principle of chemistry used to predict the effect of a change in conditions on chemical equilibria. The principle is named after French chemist Henry Louis Le Chatelier, and sometimes also credited to Karl Ferdinand Braun, who discovered it independently. It can be stated as:
When any system at equilibrium for a long period of time is subjected to a change in concentration, temperature, volume, or pressure, (1) the system changes to a new equilibrium, and (2) this change partly counteracts the applied change.
It is common to treat the principle as a more general observation of systems,[312] such as
When a settled system is disturbed, it will adjust to diminish the change that has been made to it
or, "roughly stated",[312]
Any change in status quo prompts an opposing reaction in the responding system.
- Lenz's law
- Lenz's law, named after the physicist Emil Lenz who formulated it in 1834,[313] states that the direction of the electric current which is induced in a conductor by a changing magnetic field is such that the magnetic field created by the induced current opposes the initial changing magnetic field. It is a qualitative law that specifies the direction of induced current, but states nothing about its magnitude. Lenz's law explains the direction of many effects in electromagnetism, such as the direction of voltage induced in an inductor or wire loop by a changing current, or the drag force of eddy currents exerted on moving objects in a magnetic field. Lenz's law may be seen as analogous to Newton's third law in classical mechanics.[314]
- Lepton
- In particle physics, a lepton is an elementary particle of half-integer spin (spin 1⁄2) that does not undergo strong interactions.[315] Two main classes of leptons exist: charged leptons (also known as the electron-like leptons), and neutral leptons (better known as neutrinos). Charged leptons can combine with other particles to form various composite particles such as atoms and positronium, while neutrinos rarely interact with anything, and are consequently rarely observed. The best known of all leptons is the electron.
- Lever
- Is a simple machine consisting of a beam or rigid rod pivoted at a fixed hinge, or fulcrum. A lever is a rigid body capable of rotating on a point on itself. On the basis of the locations of fulcrum, load and effort, the lever is divided into three types. Also, leverage is mechanical advantage gained in a system. It is one of the six simple machines identified by Renaissance scientists. A lever amplifies an input force to provide a greater output force, which is said to provide leverage. The ratio of the output force to the input force is the mechanical advantage of the lever. As such, the lever is a mechanical advantage device, trading off force against movement.
- L'Hôpital's rule
- In mathematics, more specifically calculus, L'Hôpital's rule or L'Hospital's rule (French: [lopital],
English: /ˌloʊpiːˈtɑːl/, loh-pee-TAHL) provides a technique to evaluate limits of indeterminate forms. Application (or repeated application) of the rule often converts an indeterminate form to an expression that can be easily evaluated by substitution. The rule is named after the 17th-century French mathematician Guillaume de l'Hôpital. Although the rule is often attributed to L'Hôpital, the theorem was first introduced to him in 1694 by the Swiss mathematician Johann Bernoulli.
L'Hôpital's rule states that for functions f and g which are differentiable on an open interval I except possibly at a point c contained in I, if and for all x in I with x ≠ c, and exists, then
- Light
- Light or visible light is electromagnetic radiation within the portion of the electromagnetic spectrum that can be perceived by the human eye.[316] Visible light is usually defined as having wavelengths in the range of 400–700 nm, between the infrared (with longer wavelengths) and the ultraviolet (with shorter wavelengths).[317][318] This wavelength means a frequency range of roughly 430–750 terahertz (THz).
- Linear actuator
- Is an actuator that creates motion in a straight line, in contrast to the circular motion of a conventional electric motor. Linear actuators are used in machine tools and industrial machinery, in computer peripherals such as disk drives and printers, in valves and dampers, and in many other places where linear motion is required. Hydraulic or pneumatic cylinders inherently produce linear motion. Many other mechanisms are used to generate linear motion from a rotating motor.
- Linear algebra
- The mathematics of equations where the unknowns are only in the first power.
- Linear elasticity
- Is a mathematical model of how solid objects deform and become internally stressed due to prescribed loading conditions. It is a simplification of the more general nonlinear theory of elasticity and a branch of continuum mechanics.
- Liquid
- A liquid is a nearly incompressible fluid that conforms to the shape of its container but retains a (nearly) constant volume independent of pressure. As such, it is one of the four fundamental states of matter (the others being solid, gas, and plasma), and is the only state with a definite volume but no fixed shape. A liquid is made up of tiny vibrating particles of matter, such as atoms, held together by intermolecular bonds. Like a gas, a liquid is able to flow and take the shape of a container. Most liquids resist compression, although others can be compressed. Unlike a gas, a liquid does not disperse to fill every space of a container, and maintains a fairly constant density. A distinctive property of the liquid state is surface tension, leading to wetting phenomena. Water is, by far, the most common liquid on Earth.
- Logarithm
- In mathematics, the logarithm is the inverse function to exponentiation. That means the logarithm of a given number x is the exponent to which another fixed number, the base b, must be raised, to produce that number x. In the simplest case, the logarithm counts the number of occurrences of the same factor in repeated multiplication; e.g., since 1000 = 10 × 10 × 10 = 103, the "logarithm base 10" of 1000 is 3, or log10(1000) = 3. The logarithm of x to base b is denoted as logb(x), or without parentheses, logb x, or even without the explicit base, log x, when no confusion is possible, or when the base does not matter such as in big O notation.
More generally, exponentiation allows any positive real number as base to be raised to any real power, always producing a positive result, so logb(x) for any two positive real numbers b and x, where b is not equal to 1, is always a unique real number y. More explicitly, the defining relation between exponentiation and logarithm is:
- exactly if and and and .
- Logarithmic identities
- Several important formulas, sometimes called logarithmic identities or log laws, relate logarithms to one another.[320]
- Logarithmic mean temperature difference
- (Also known as log mean temperature difference, LMTD) is used to determine the temperature driving force for heat transfer in flow systems, most notably in heat exchangers. The LMTD is a logarithmic average of the temperature difference between the hot and cold feeds at each end of the double pipe exchanger. For a given heat exchanger with constant area and heat transfer coefficient, the larger the LMTD, the more heat is transferred. The use of the LMTD arises straightforwardly from the analysis of a heat exchanger with constant flow rate and fluid thermal properties.
- Lumped capacitance model
- A lumped-capacitance model, also called lumped system analysis,[321] reduces a thermal system to a number of discrete "lumps" and assumes that the temperature difference inside each lump is negligible. This approximation is useful to simplify otherwise complex differential heat equations. It was developed as a mathematical analog of electrical capacitance, although it also includes thermal analogs of electrical resistance as well.
- Lumped element model
- The lumped-element model (also called lumped-parameter model, or lumped-component model) simplifies the description of the behaviour of spatially distributed physical systems into a topology consisting of discrete entities that approximate the behaviour of the distributed system under certain assumptions. It is useful in electrical systems (including electronics), mechanical multibody systems, heat transfer, acoustics, etc. Mathematically speaking, the simplification reduces the state space of the system to a finite dimension, and the partial differential equations (PDEs) of the continuous (infinite-dimensional) time and space model of the physical system into ordinary differential equations (ODEs) with a finite number of parameters.
M[]
N[]
- Nanoengineering
- Is the practice of engineering on the nanoscale. It derives its name from the nanometre, a unit of measurement equalling one billionth of a meter. Nanoengineering is largely a synonym for nanotechnology, but emphasizes the engineering rather than the pure science aspects of the field.
- Nanotechnology
- The technology of systems built with moving parts on the order of a nanometre in size.
- In physics, the Navier–Stokes equations are a set of partial differential equations which describe the motion of viscous fluid substances, named after French engineer and physicist Claude-Louis Navier and Anglo-Irish physicist and mathematician George Gabriel Stokes.
- Neutrino
- A neutrino (denoted by the Greek letter ν) is a fermion (an elementary particle with spin of 1/2) that interacts only via the weak subatomic force and gravity.[322][323] The neutrino is so named because it is electrically neutral and because its rest mass is so small (-ino) that it was long thought to be zero. The mass of the neutrino is much smaller than that of the other known elementary particles.[324] The weak force has a very short range, the gravitational interaction is extremely weak, and neutrinos do not participate in the strong interaction.[325] Thus, neutrinos typically pass through normal matter unimpeded and undetected.[326][323]
- Newtonian fluid
- Is a fluid in which the viscous stresses arising from its flow, at every point, are linearly[327] correlated to the local strain rate—the rate of change of its deformation over time.[328][329][330] That is equivalent to saying those forces are proportional to the rates of change of the fluid's velocity vector as one moves away from the point in question in various directions. More precisely, a fluid is Newtonian only if the tensors that describe the viscous stress and the strain rate are related by a constant viscosity tensor that does not depend on the stress state and velocity of the flow. If the fluid is also isotropic (that is, its mechanical properties are the same along any direction), the viscosity tensor reduces to two real coefficients, describing the fluid's resistance to continuous shear deformation and continuous compression or expansion, respectively.
- Norton's theorem
- In direct-current circuit theory, Norton's theorem (aka Mayer–Norton theorem) is a simplification that can be applied to networks made of linear time-invariant resistances, voltage sources, and current sources. At a pair of terminals of the network, it can be replaced by a current source and a single resistor in parallel. For alternating current (AC) systems the theorem can be applied to reactive impedances as well as resistances.
- Nozzle
- Is a device designed to control the direction or characteristics of a fluid flow (especially to increase velocity) as it exits (or enters) an enclosed chamber or pipe. A nozzle is often a pipe or tube of varying cross sectional area, and it can be used to direct or modify the flow of a fluid (liquid or gas). Nozzles are frequently used to control the rate of flow, speed, direction, mass, shape, and/or the pressure of the stream that emerges from them. In a nozzle, the velocity of fluid increases at the expense of its pressure energy.
- nth root
- To put a number of function to the exponential power of 1/n.
- Nuclear binding energy
- The difference between the total mass energy of a nucleus and the mass energy of the isolated nucleons.
- Nuclear engineering
- The profession that deals with nuclear power.
- Nuclear fusion
- Is a reaction in which two or more atomic nuclei are combined to form one or more different atomic nuclei and subatomic particles (neutrons or protons). The difference in mass between the reactants and products is manifested as either the release or the absorption of energy. This difference in mass arises due to the difference in atomic binding energy between the nuclei before and after the reaction. Fusion is the process that powers active or main sequence stars and other high-magnitude stars, where large amounts of energy are released.
- Nuclear physics
- The science that describes the components of atoms.
- Nuclear potential energy
- The energy that is given up in decay of an unstable nucleus.
- Nuclear power
- The use of energy derived from nuclear chain reactions for electricity production or ship propulsion.
O[]
- Ohm
- The SI unit of electrical resistance.
- Ohm's law
- A law describing the relationship between resistance, current, and voltage.
- Optics
- The study of light.
- Organic chemistry
- The study of carbon compounds.
- Osmosis
- The spontaneous movement of molecules or ions through a semi-permable membrane, tending to equalize concentration on both sides.
P[]
- Parallel circuit
- A circuit that begins and ends at the same node as another circuit.
- Parity (mathematics)
- In mathematics, parity is the property of an integer of whether it is even or odd. An integer's parity is even if it is divisible by two with no remainders left and its parity is odd if its remainder is 1.[331] For example, -4, 0, 82, and 178 are even because there is no remainder when dividing it by 2. By contrast, -3, 5, 7, 21 are odd numbers as they leave a remainder of 1 when divided by 2.
- Parity (physics)
- In quantum mechanics, a parity transformation (also called parity inversion) is the flip in the sign of one spatial coordinate. In three dimensions, it can also refer to the simultaneous flip in the sign of all three spatial coordinates (a point reflection):
- Paramagnetism
- Is a form of magnetism whereby some materials are weakly attracted by an externally applied magnetic field, and form internal, induced magnetic fields in the direction of the applied magnetic field. In contrast with this behavior, diamagnetic materials are repelled by magnetic fields and form induced magnetic fields in the direction opposite to that of the applied magnetic field.[332] Paramagnetic materials include most chemical elements and some compounds;[333] they have a relative magnetic permeability slightly greater than 1 (i.e., a small positive magnetic susceptibility) and hence are attracted to magnetic fields. The magnetic moment induced by the applied field is linear in the field strength and rather weak. It typically requires a sensitive analytical balance to detect the effect and modern measurements on paramagnetic materials are often conducted with a SQUID magnetometer.
- Particle accelerator
- Is a machine that uses electromagnetic fields to propel charged particles to very high speeds and energies, and to contain them in well-defined beams.[334]
- Particle displacement
- Particle displacement or displacement amplitude is a measurement of distance of the movement of a sound particle from its equilibrium position in a medium as it transmits a sound wave.[335] The SI unit of particle displacement is the metre (m). In most cases this is a longitudinal wave of pressure (such as sound), but it can also be a transverse wave, such as the vibration of a taut string. In the case of a sound wave travelling through air, the particle displacement is evident in the oscillations of air molecules with, and against, the direction in which the sound wave is travelling.[336]
- Particle physics
- Particle physics (also known as high energy physics) is a branch of physics that studies the nature of the particles that constitute matter and radiation. Although the word particle can refer to various types of very small objects (e.g. protons, gas particles, or even household dust), particle physics usually investigates the irreducibly smallest detectable particles and the fundamental interactions necessary to explain their behaviour. In current understanding, these elementary particles are excitations of the quantum fields that also govern their interactions. The currently dominant theory explaining these fundamental particles and fields, along with their dynamics, is called the Standard Model. Thus, modern particle physics generally investigates the Standard Model and its various possible extensions, e.g. to the newest "known" particle, the Higgs boson, or even to the oldest known force field, gravity.[337][338]
- Pascal's law
- Pascal's law (also Pascal's principle[339][340][341] or the principle of transmission of fluid-pressure) is a principle in fluid mechanics that states that a pressure change occurring anywhere in a confined incompressible fluid is transmitted throughout the fluid such that the same change occurs everywhere.[342] The law was established by French mathematician Blaise Pascal[30] in 1647–48.[343]
- Pendulum
- Is a weight suspended from a pivot so that it can swing freely.[344] When a pendulum is displaced sideways from its resting, equilibrium position, it is subject to a restoring force due to gravity that will accelerate it back toward the equilibrium position. When released, the restoring force acting on the pendulum's mass causes it to oscillate about the equilibrium position, swinging back and forth. The time for one complete cycle, a left swing and a right swing, is called the period. The period depends on the length of the pendulum and also to a slight degree on the amplitude, the width of the pendulum's swing.
- Petroleum engineering
- Is a field of engineering concerned with the activities related to the production of Hydrocarbons, which can be either crude oil or natural gas.[345] Exploration and production are deemed to fall within the upstream sector of the oil and gas industry. Exploration, by earth scientists, and petroleum engineering are the oil and gas industry's two main subsurface disciplines, which focus on maximizing economic recovery of hydrocarbons from subsurface reservoirs. Petroleum geology and geophysics focus on provision of a static description of the hydrocarbon reservoir rock, while petroleum engineering focuses on estimation of the recoverable volume of this resource using a detailed understanding of the physical behavior of oil, water and gas within porous rock at very high pressure.
- pH
- A logarithmic measure of the concentration of hydrogen ions in an acid or base solution.
- Phase (matter)
- In the physical sciences, a phase is a region of space (a thermodynamic system), throughout which all physical properties of a material are essentially uniform.[346][347]: 86 [348]: 3 Examples of physical properties include density, index of refraction, magnetization and chemical composition. A simple description is that a phase is a region of material that is chemically uniform, physically distinct, and (often) mechanically separable. In a system consisting of ice and water in a glass jar, the ice cubes are one phase, the water is a second phase, and the humid air is a third phase over the ice and water. The glass of the jar is another separate phase. (See state of matter § Glass)
- Phase (waves)
- In physics and mathematics, the phase of a periodic function of some real variable (such as time) is an angle-like quantity representing the fraction of the cycle covered up to . It is denoted and expressed in such a scale that it varies by one full turn as the variable goes through each period (and goes through each complete cycle). It may be measured in any angular unit such as degrees or radians, thus increasing by 360° or as the variable completes a full period.[349]
- Phase diagram
- A phase diagram in physical chemistry, engineering, mineralogy, and materials science is a type of chart used to show conditions (pressure, temperature, volume, etc.) at which thermodynamically distinct phases (such as solid, liquid or gaseous states) occur and coexist at equilibrium.
- Phase rule
- In thermodynamics, the phase rule is a general principle governing "pVT" systems (that is, systems whose states are completely described by the variables pressure (p), volume (V) and temperature (T)) in thermodynamic equilibrium. If F is the number of degrees of freedom, C is the number of components and P is the number of phases, then[350][105]
- Photon
- Is a type of elementary particle. It is the quantum of the electromagnetic field including electromagnetic radiation such as light and radio waves, and the force carrier for the electromagnetic force. Photons are massless,[c] so they always move at the speed of light in vacuum, 299792458 m/s (or about 186,282 mi/s). The photon belongs to the class of bosons.
- Physical chemistry
- Is the study of macroscopic, and particulate phenomena in chemical systems in terms of the principles, practices, and concepts of physics such as motion, energy, force, time, thermodynamics, quantum chemistry, statistical mechanics, analytical dynamics and chemical equilibrium.
- Physical quantity
- A physical quantity is a property of a material or system that can be quantified by measurement. A physical quantity can be expressed as a value, which is the algebraic multiplication of a numerical value and a unit. For example, the physical quantity mass can be quantified as n kg, where n is the numerical value and kg is the unit. A physical quantity possesses at least two characteristics in common. One is numerical magnitude and the other is the unit in which it is measured.
- Physics
- Is the natural science that studies matter,[d] its motion and behavior through space and time, and the related entities of energy and force.[353] Physics is one of the most fundamental scientific disciplines, and its main goal is to understand how the universe behaves.[e][354][355][356]
- Planck constant
- The Planck constant, or Planck's constant, is a fundamental physical constant denoted , and is of fundamental importance in quantum mechanics. A photon's energy is equal to its frequency multiplied by the Planck constant. Due to mass–energy equivalence, the Planck constant also relates mass to frequency. In metrology it is used, together with other constants, to define the kilogram, an SI unit.[357] The SI units are defined in such a way that, when the Planck constant is expressed in SI units, it has the exact value = 6.62607015×10−34 J⋅Hz−1.[358][359]
- Plasma (physics)
- Is one of the four fundamental states of matter, first systematically studied by Irving Langmuir in the 1920s.[360][361] It consists of a gas of ions – atoms or molecules which have one or more orbital electrons stripped (or, rarely, an extra electron attached), and free electrons.
- Plasticity
- In physics and materials science, plasticity, also known as plastic deformation, is the ability of a solid material to undergo permanent deformation, a non-reversible change of shape in response to applied forces.[362][363] For example, a solid piece of metal being bent or pounded into a new shape displays plasticity as permanent changes occur within the material itself. In engineering, the transition from elastic behavior to plastic behavior is known as yielding.
- Pneumatics
- The control of mechanical force and movement, generated by the application of compressed gas.
- Point estimation
- In statistics, point estimation involves the use of sample data to calculate a single value (known as a point estimate since it identifies a point in some parameter space) which is to serve as a "best guess" or "best estimate" of an unknown population parameter (for example, the population mean). More formally, it is the application of a point estimator to the data to obtain a point estimate. Point estimation can be contrasted with interval estimation: such interval estimates are typically either confidence intervals, in the case of frequentist inference, or credible intervals, in the case of Bayesian inference. More generally, a point estimator can be contrasted with a set estimator. Examples are given by confidence sets or credible sets. A point estimator can also be contrasted with a distribution estimator. Examples are given by confidence distributions, randomized estimators, and Bayesian posteriors.
- Polyphase system
- An electrical system that uses a set of alternating currents at different phases.
- Power (electric)
- Electric power is the rate, per unit time, at which electrical energy is transferred by an electric circuit. The SI unit of power is the watt, one joule per second. Electric power is usually produced by electric generators, but can also be supplied by sources such as electric batteries. It is usually supplied to businesses and homes (as domestic mains electricity) by the electric power industry through an electric power grid. Electric power can be delivered over long distances by transmission lines and used for applications such as motion, light or heat with high efficiency.[364]
- Power (physics)
- In physics, power is the amount of energy transferred or converted per unit time. In the International System of Units, the unit of power is the watt, equal to one joule per second. In older works, power is sometimes called activity.[365][366][367] Power is a scalar quantity.
- Power factor
- In electrical engineering, the power factor of an AC power system is defined as the ratio of the real power absorbed by the load to the apparent power flowing in the circuit, and is a dimensionless number in the closed interval of −1 to 1. A power factor of less than one indicates the voltage and current are not in phase, reducing the average product of the two. Real power is the instantaneous product of voltage and current and represents the capacity of the electricity for performing work. Apparent power is the product of RMS current and voltage. Due to energy stored in the load and returned to the source, or due to a non-linear load that distorts the wave shape of the current drawn from the source, the apparent power may be greater than the real power. A negative power factor occurs when the device (which is normally the load) generates power, which then flows back towards the source.
- Pressure
- Pressure (symbol: p or P) is the force applied perpendicular to the surface of an object per unit area over which that force is distributed.: 445 [368] Gauge pressure (also spelled gage pressure)[f] is the pressure relative to the ambient pressure. Various units are used to express pressure. Some of these derive from a unit of force divided by a unit of area; the SI unit of pressure, the pascal (Pa), for example, is one newton per square metre (N/m2); similarly, the pound-force per square inch (psi) is the traditional unit of pressure in the imperial and U.S. customary systems. Pressure may also be expressed in terms of standard atmospheric pressure; the atmosphere (atm) is equal to this pressure, and the torr is defined as 1⁄760 of this. Manometric units such as the centimetre of water, millimetre of mercury, and inch of mercury are used to express pressures in terms of the height of column of a particular fluid in a manometer.
- Probability
- Is the branch of mathematics concerning numerical descriptions of how likely an event is to occur, or how likely it is that a proposition is true. The probability of an event is a number between 0 and 1, where, roughly speaking, 0 indicates impossibility of the event and 1 indicates certainty.[note 3][369][370] The higher the probability of an event, the more likely it is that the event will occur. A simple example is the tossing of a fair (unbiased) coin. Since the coin is fair, the two outcomes ("heads" and "tails") are both equally probable; the probability of "heads" equals the probability of "tails"; and since no other outcomes are possible, the probability of either "heads" or "tails" is 1/2 (which could also be written as 0.5 or 50%).
- Probability distribution
- In probability theory and statistics, a probability distribution is the mathematical function that gives the probabilities of occurrence of different possible outcomes for an experiment.[371][372] It is a mathematical description of a random phenomenon in terms of its sample space and the probabilities of events (subsets of the sample space).[373] For instance, if X is used to denote the outcome of a coin toss ("the experiment"), then the probability distribution of X would take the value 0.5 (1 in 2 or 1/2) for X = heads, and 0.5 for X = tails (assuming that the coin is fair). Examples of random phenomena include the weather condition in a future date, the height of a randomly selected person, the fraction of male students in a school, the results of a survey to be conducted, etc.[374]
- Probability theory
- is the branch of mathematics concerned with probability. Although there are several different probability interpretations, probability theory treats the concept in a rigorous mathematical manner by expressing it through a set of axioms. Typically these axioms formalise probability in terms of a probability space, which assigns a measure taking values between 0 and 1, termed the probability measure, to a set of outcomes called the sample space. Any specified subset of these outcomes is called an event. Central subjects in probability theory include discrete and continuous random variables, probability distributions, and stochastic processes, which provide mathematical abstractions of non-deterministic or uncertain processes or measured quantities that may either be single occurrences or evolve over time in a random fashion. Although it is not possible to perfectly predict random events, much can be said about their behavior. Two major results in probability theory describing such behaviour are the law of large numbers and the central limit theorem. As a mathematical foundation for statistics, probability theory is essential to many human activities that involve quantitative analysis of data.[375] Methods of probability theory also apply to descriptions of complex systems given only partial knowledge of their state, as in statistical mechanics or sequential estimation. A great discovery of twentieth-century physics was the probabilistic nature of physical phenomena at atomic scales, described in quantum mechanics.[376]
- Pulley
- Is a wheel on an axle or shaft that is designed to support movement and change of direction of a taut cable or belt, or transfer of power between the shaft and cable or belt. In the case of a pulley supported by a frame or shell that does not transfer power to a shaft, but is used to guide the cable or exert a force, the supporting shell is called a block, and the pulley may be called a sheave. A pulley may have a groove or grooves between flanges around its circumference to locate the cable or belt. The drive element of a pulley system can be a rope, cable, belt, or chain.
- Pump
- Is a device that moves fluids (liquids or gases), or sometimes slurries, by mechanical action, typically converted from electrical energy into hydraulic energy. Pumps can be classified into three major groups according to the method they use to move the fluid: direct lift, displacement, and gravity pumps.[377] Pumps operate by some mechanism (typically reciprocating or rotary), and consume energy to perform mechanical work moving the fluid. Pumps operate via many energy sources, including manual operation, electricity, engines, or wind power, and come in many sizes, from microscopic for use in medical applications, to large industrial pumps.
Q[]
- Quantum electrodynamics
- In particle physics, quantum electrodynamics (QED) is the relativistic quantum field theory of electrodynamics. In essence, it describes how light and matter interact and is the first theory where full agreement between quantum mechanics and special relativity is achieved. QED mathematically describes all phenomena involving electrically charged particles interacting by means of exchange of photons and represents the quantum counterpart of classical electromagnetism giving a complete account of matter and light interaction.
- Quantum field theory
- In theoretical physics, quantum field theory (QFT) is a theoretical framework that combines classical field theory, special relativity and quantum mechanics,[378]: xi but not general relativity's description of gravity. QFT is used in particle physics to construct physical models of subatomic particles and in condensed matter physics to construct models of quasiparticles.
- Quantum mechanics
- Is a fundamental theory in physics that provides a description of the physical properties of nature at the scale of atoms and subatomic particles.[379]: 1.1 It is the foundation of all quantum physics including quantum chemistry, quantum field theory, quantum technology, and quantum information science.
R[]
- Regelation
- The phenomena of melting under pressure, then freezing when the pressure is reduced.
- Relative density
- Relative density, or specific gravity,[380][381] is the ratio of the density (mass of a unit volume) of a substance to the density of a given reference material. Specific gravity for liquids is nearly always measured with respect to water at its densest (at 4 °C or 39.2 °F); for gases, the reference is air at room temperature (20 °C or 68 °F). The term "relative density" is often preferred in scientific usage.
- Relative velocity
- The relative velocity (also or ) is the velocity of an object or observer B in the rest frame of another object or observer A.
- Reliability engineering
- Is a sub-discipline of systems engineering that emphasizes the ability of equipment to function without failure. Reliability describes the ability of a system or component to function under stated conditions for a specified period of time.[382] Reliability is closely related to availability, which is typically described as the ability of a component or system to function at a specified moment or interval of time.
- Resistivity
- Electrical resistivity (also called specific electrical resistance or volume resistivity) and its inverse, electrical conductivity, is a fundamental property of a material that quantifies how strongly it resists or conducts electric current. A low resistivity indicates a material that readily allows electric current. Resistivity is commonly represented by the Greek letter ρ (rho). The SI unit of electrical resistivity is the ohm-meter (Ω⋅m).[383][384][385] For example, if a 1 m × 1 m × 1 m solid cube of material has sheet contacts on two opposite faces, and the resistance between these contacts is 1 Ω, then the resistivity of the material is 1 Ω⋅m.
- Resistor
- Is a passive two-terminal electrical component that implements electrical resistance as a circuit element. In electronic circuits, resistors are used to reduce current flow, adjust signal levels, to divide voltages, bias active elements, and terminate transmission lines, among other uses. High-power resistors that can dissipate many watts of electrical power as heat, may be used as part of motor controls, in power distribution systems, or as test loads for generators. Fixed resistors have resistances that only change slightly with temperature, time or operating voltage. Variable resistors can be used to adjust circuit elements (such as a volume control or a lamp dimmer), or as sensing devices for heat, light, humidity, force, or chemical activity.
- Reynolds number
- The Reynolds number (Re) helps predict flow patterns in different fluid flow situations. At low Reynolds numbers, flows tend to be dominated by laminar (sheet-like) flow, while at high Reynolds numbers flows tend to be turbulent. The turbulence results from differences in the fluid's speed and direction, which may sometimes intersect or even move counter to the overall direction of the flow (eddy currents). These eddy currents begin to churn the flow, using up energy in the process, which for liquids increases the chances of cavitation. Reynolds numbers are an important dimensionless quantity in fluid mechanics.
- Rheology
- Is the study of the flow of matter, primarily in a liquid or gas state, but also as "soft solids" or solids under conditions in which they respond with plastic flow rather than deforming elastically in response to an applied force. Rheology is a branch of physics, and it is the science that deals with the deformation and flow of materials, both solids and liquids.[386]
- Rigid body
- In physics, a rigid body (also known as a rigid object [387]) is a solid body in which deformation is zero or so small it can be neglected. The distance between any two given points on a rigid body remains constant in time regardless of external forces or moments exerted on it. A rigid body is usually considered as a continuous distribution of mass. In the study of special relativity, a perfectly rigid body does not exist; and objects can only be assumed to be rigid if they are not moving near the speed of light. In quantum mechanics, a rigid body is usually thought of as a collection of point masses. For instance, molecules (consisting of the point masses: electrons and nuclei) are often seen as rigid bodies (see classification of molecules as rigid rotors).
- Robonaut
- A development project conducted by NASA to create humanoid robots capable of using space tools and working in similar environments to suited astronauts.
- Robot-assisted surgery
- Robotic surgery are types of surgical procedures that are done using robotic systems. Robotically-assisted surgery was developed to try to overcome the limitations of pre-existing minimally-invasive surgical procedures and to enhance the capabilities of surgeons performing open surgery. In the case of robotically-assisted minimally-invasive surgery, instead of directly moving the instruments, the surgeon uses one of two methods to administer the instruments. These include using a direct telemanipulator or through computer control. A telemanipulator is a remote manipulator that allows the surgeon to perform the normal movements associated with the surgery. The robotic arms carry out those movements using end-effectors and manipulators to perform the actual surgery. In computer-controlled systems, the surgeon uses a computer to control the robotic arms and its end-effectors, though these systems can also still use telemanipulators for their input. One advantage of using the computerized method is that the surgeon does not have to be present, leading to the possibility for remote surgery.
- Robotics
- Is an interdisciplinary field that integrates computer science and engineering.[388] Robotics involves design, construction, operation, and use of robots. The goal of robotics is to design machines that can help and assist humans. Robotics integrates fields of mechanical engineering, electrical engineering, information engineering, mechatronics, electronics, bioengineering, computer engineering, control engineering, software engineering, among others.
- Root mean square
- In mathematics and its applications, the root mean square (RMS or rms) is defined as the square root of the mean square (the arithmetic mean of the squares of a set of numbers).[389] The RMS is also known as the quadratic mean[390][391] and is a particular case of the generalized mean with exponent 2. RMS can also be defined for a continuously varying function in terms of an integral of the squares of the instantaneous values during a cycle. For alternating electric current, RMS is equal to the value of the constant direct current that would produce the same power dissipation in a resistive load.[389] In estimation theory, the root-mean-square deviation of an estimator is a measure of the imperfection of the fit of the estimator to the data.
- Root-mean-square speed
- In the physics of gas molecules, the root-mean-square speed is defined as the square root of the average squared-speed. The RMS speed of an ideal gas is calculated using the following equation:
- Rotational energy
- Rotational energy or angular kinetic energy is kinetic energy due to the rotation of an object and is part of its total kinetic energy. Looking at rotational energy separately around an object's axis of rotation, the following dependence on the object's moment of inertia is observed:
- is the angular velocity
- is the moment of inertia around the axis of rotation
- is the kinetic energy
- is rotational speed in cycles per second
- is angular speed in radians per second
- is angular speed in degrees per second
S[]
- Safe failure fraction (SFF)
- A term used in functional safety for the proportion of failures that are either non-hazardous or detected automatically. The opposite of SFF is the proportion of undetected, hazardous failures.[394]
- Safety data sheet
- A safety data sheet (SDS),[395] material safety data sheet (MSDS), or product safety data sheet (PSDS) are documents that list information relating to occupational safety and health for the use of various substances and products. SDSs are a widely used system for cataloguing information on chemicals, chemical compounds, and chemical mixtures. SDS information may include instructions for the safe use and potential hazards associated with a particular material or product, along with spill-handling procedures. The older MSDS formats could vary from source to source within a country depending on national requirements; however, the newer SDS format is internationally standardized.
- Sanitary engineering
- Sanitary engineering, also known as public health engineering or wastewater engineering, is the application of engineering methods to improve sanitation of human communities, primarily by providing the removal and disposal of human waste, and in addition to the supply of safe potable water.
- Saturated compound
- In chemistry, a saturated compound is a chemical compound (or ion) that resists the addition reactions, such as hydrogenation, oxidative addition, and binding of a Lewis base. The term is used in many contexts and for many classes of chemical compounds. Overall, saturated compounds are less reactive than unsaturated compounds. Saturation is derived from the Latin word saturare, meaning 'to fill')[396]
- Scalar (mathematics)
- .
- Scalar (physics)
- .
- Scalar multiplication
- In mathematics, scalar multiplication is one of the basic operations defining a vector space in linear algebra[397][398][399] (or more generally, a module in abstract algebra[400][401]). In common geometrical contexts, scalar multiplication of a real Euclidean vector by a positive real number multiplies the magnitude of the vector—without changing its direction. The term "scalar" itself derives from this usage: a scalar is that which scales vectors. Scalar multiplication is the multiplication of a vector by a scalar (where the product is a vector), and is to be distinguished from inner product of two vectors (where the product is a scalar).
- Screw
- A screw is a mechanism that converts rotational motion to linear motion, and a torque (rotational force) to a linear force.[402] It is one of the six classical simple machines. The most common form consists of a cylindrical shaft with helical grooves or ridges called threads around the outside.[403][404] The screw passes through a hole in another object or medium, with threads on the inside of the hole that mesh with the screw's threads. When the shaft of the screw is rotated relative to the stationary threads, the screw moves along its axis relative to the medium surrounding it; for example rotating a wood screw forces it into wood. In screw mechanisms, either the screw shaft can rotate through a threaded hole in a stationary object, or a threaded collar such as a nut can rotate around a stationary screw shaft.[405][406] Geometrically, a screw can be viewed as a narrow inclined plane wrapped around a cylinder.[402]
- Series circuit
- An electrical circuit in which the same current passes through each component, with only one path.
- Servo
- A motor that moves to and maintains a set position under command, rather than continuously moving.
- Servomechanism
- An automatic device that uses error-sensing negative feedback to correct the performance of a mechanism.
- Shadow matter
- In physics, mirror matter, also called shadow matter or Alice matter, is a hypothetical counterpart to ordinary matter.[407]
- Shear flow
- The term shear flow is used in solid mechanics as well as in fluid dynamics. The expression shear flow is used to indicate:
- a shear stress over a distance in a thin-walled structure (in solid mechanics);[408]
- the flow induced by a force (in a fluid).
- Shear strength
- Is the strength of a material or component against the type of yield or structural failure when the material or component fails in shear. A shear load is a force that tends to produce a sliding failure on a material along a plane that is parallel to the direction of the force. When a paper is cut with scissors, the paper fails in shear. In structural and mechanical engineering, the shear strength of a component is important for designing the dimensions and materials to be used for the manufacture or construction of the component (e.g. beams, plates, or bolts). In a reinforced concrete beam, the main purpose of reinforcing bar (rebar) stirrups is to increase the shear strength.
- Shear stress
- Shear stress, often denoted by τ (Greek: tau), is the component of stress coplanar with a material cross section. It arises from the shear force, the component of force vector parallel to the material cross section. Normal stress, on the other hand, arises from the force vector component perpendicular to the material cross section on which it acts.
- Shortwave radiation
- Shortwave radiation (SW) is radiant energy with wavelengths in the visible (VIS), near-ultraviolet (UV), and near-infrared (NIR) spectra. There is no standard cut-off for the near-infrared range; therefore, the shortwave radiation range is also variously defined. It may be broadly defined to include all radiation with a wavelength of 0.1μm and 5.0μm or narrowly defined so as to include only radiation between 0.2μm and 3.0μm. There is little radiation flux (in terms of W/m2) to the Earth's surface below 0.2μm or above 3.0μm, although photon flux remains significant as far as 6.0μm, compared to shorter wavelength fluxes. UV-C radiation spans from 0.1μm to .28μm, UV-B from 0.28μm to 0.315μm, UV-A from 0.315μm to 0.4μm, the visible spectrum from 0.4μm to 0.7μm, and NIR arguably from 0.7μm to 5.0μm, beyond which the infrared is thermal.[409] Shortwave radiation is distinguished from longwave radiation. Downward shortwave radiation is sensitive to solar zenith angle, cloud cover.[410]
- SI units
- The International System of Units (SI, abbreviated from the French Syst��me international (d'unités)) is the modern form of the metric system. It is the only system of measurement with an official status in nearly every country in the world. It comprises a coherent system of units of measurement starting with seven base units, which are the second (the unit of time with the symbol s), metre (length, m), kilogram (mass, kg), ampere (electric current, A), kelvin (thermodynamic temperature, K), mole (amount of substance, mol), and candela (luminous intensity, cd). The system allows for an unlimited number of additional units, called derived units, which can always be represented as products of powers of the base units.[g] Twenty-two derived units have been provided with special names and symbols.[h] The seven base units and the 22 derived units with special names and symbols may be used in combination to express other derived units,[i] which are adopted to facilitate measurement of diverse quantities. The SI also provides twenty prefixes to the unit names and unit symbols that may be used when specifying power-of-ten (i.e. decimal) multiples and sub-multiples of SI units. The SI is intended to be an evolving system; units and prefixes are created and unit definitions are modified through international agreement as the technology of measurement progresses and the precision of measurements improves.
- Signal processing
- Is an electrical engineering subfield that focuses on analysing, modifying, and synthesizing signals such as sound, images, and scientific measurements.[411] Signal processing techniques can be used to improve transmission, storage efficiency and subjective quality and to also emphasize or detect components of interest in a measured signal.[412]
- Simple machine
- Is a mechanical device that changes the direction or magnitude of a force.[413] In general, they can be defined as the simplest mechanisms that use mechanical advantage (also called leverage) to multiply force.[414] Usually the term refers to the six classical simple machines that were defined by Renaissance scientists:[415][416][417]
- Lever
- Wheel and axle
- Pulley
- Inclined plane
- Wedge
- Screw
- Siphon
- A closed tube that conveys liquids between two levels without pumping.
- Solid mechanics
- Also known as mechanics of solids, is the branch of continuum mechanics that studies the behavior of solid materials, especially their motion and deformation under the action of forces, temperature changes, phase changes, and other external or internal agents.
- Solid-state physics
- Is the study of rigid matter, or solids, through methods such as quantum mechanics, crystallography, electromagnetism, and metallurgy. It is the largest branch of condensed matter physics. Solid-state physics studies how the large-scale properties of solid materials result from their atomic-scale properties. Thus, solid-state physics forms a theoretical basis of materials science. It also has direct applications, for example in the technology of transistors and semiconductors.
- Solid solution strengthening
- Is a type of alloying that can be used to improve the strength of a pure metal.[418] The technique works by adding atoms of one element (the alloying element) to the crystalline lattice of another element (the base metal), forming a solid solution. The local nonuniformity in the lattice due to the alloying element makes plastic deformation more difficult by impeding dislocation motion through stress fields. In contrast, alloying beyond the solubility limit can form a second phase, leading to strengthening via other mechanisms (e.g. the precipitation of intermetallic compounds).
- Solubility
- Is the property of a solid, liquid or gaseous chemical substance called solute to dissolve in a solid, liquid or gaseous solvent. The solubility of a substance fundamentally depends on the physical and chemical properties of the solute and solvent as well as on temperature, pressure and presence of other chemicals (including changes to the pH) of the solution. The extent of the solubility of a substance in a specific solvent is measured as the saturation concentration, where adding more solute does not increase the concentration of the solution and begins to precipitate the excess amount of solute.
- Solubility equilibrium
- Is a type of dynamic equilibrium that exists when a chemical compound in the solid state is in chemical equilibrium with a solution of that compound. The solid may dissolve unchanged, with dissociation or with chemical reaction with another constituent of the solution, such as acid or alkali. Each solubility equilibrium is characterized by a temperature-dependent solubility product which functions like an equilibrium constant. Solubility equilibria are important in pharmaceutical, environmental and many other scenarios.
- Sound
- In physics, sound is a vibration that propagates as an acoustic wave, through a transmission medium such as a gas, liquid or solid.
- Special relativity
- In physics, the special theory of relativity, or special relativity for short, is a scientific theory regarding the relationship between space and time. In Albert Einstein's original treatment, the theory is based on two postulates:[419][420][421]
- The laws of physics are invariant (that is, identical) in all inertial frames of reference (that is, frames of reference with no acceleration).
- The speed of light in vacuum is the same for all observers, regardless of the motion of the light source or observer.
- Specific heat
- The amount of energy required to change the temperature of a unit mass of substance by one degree.
- Specific gravity
- The ratio between the mass density of a substance to that of water.
- Specific volume
- The volume of a unit mass of a substance.
- Specific weight
- The weight of a substance per unit volume.
- Spontaneous combustion
- Spontaneous combustion or spontaneous ignition is a type of combustion which occurs by self-heating (increase in temperature due to exothermic internal reactions), followed by thermal runaway (self heating which rapidly accelerates to high temperatures) and finally, autoignition.[422]
- Stagnation pressure
- In fluid dynamics, stagnation pressure (or pitot pressure) is the static pressure at a stagnation point in a fluid flow.[423] At a stagnation point the fluid velocity is zero. In an incompressible flow, stagnation pressure is equal to the sum of the free-stream static pressure and the free-stream dynamic pressure.[424]
- Standard electrode potential
- .
- State of matter
- In physics, a state of matter is one of the distinct forms in which matter can exist. Four states of matter are observable in everyday life: solid, liquid, gas, and plasma. Many intermediate states are known to exist, such as liquid crystal, and some states only exist under extreme conditions, such as Bose–Einstein condensates, neutron-degenerate matter, and quark–gluon plasma, which only occur, respectively, in situations of extreme cold, extreme density, and extremely high energy. For a complete list of all exotic states of matter, see the list of states of matter.
- Statics
- The study of forces in a non-moving, rigid body.
- Statistics
- Is the discipline that concerns the collection, organization, analysis, interpretation, and presentation of data.[425][426][427] In applying statistics to a scientific, industrial, or social problem, it is conventional to begin with a statistical population or a statistical model to be studied. Populations can be diverse groups of people or objects such as "all people living in a country" or "every atom composing a crystal". Statistics deals with every aspect of data, including the planning of data collection in terms of the design of surveys and experiments.[428]
- Steam table
- Thermodynamic data table containing steam or water properties .[429]
- Stefan–Boltzmann law
- The Stefan–Boltzmann law describes the power radiated from a black body in terms of its temperature. Specifically, the Stefan–Boltzmann law states that the total energy radiated per unit surface area of a black body across all wavelengths per unit time (also known as the black-body radiant emittance) is directly proportional to the fourth power of the black body's thermodynamic temperature T:
- Stewart platform
- Is a type of parallel manipulator that has six prismatic actuators, commonly hydraulic jacks or electric linear actuators, attached in pairs to three positions on the platform's baseplate, crossing over to three mounting points on a top plate. All 12 connections are made via universal joints. Devices placed on the top plate can be moved in the six degrees of freedom in which it is possible for a freely-suspended body to move: three linear movements x, y, z (lateral, longitudinal, and vertical), and the three rotations (pitch, roll, and yaw).
- Stiffness
- Is the extent to which an object resists deformation in response to an applied force.[432] The complementary concept is flexibility or pliability: the more flexible an object is, the less stiff it is.[433]
- Stoichiometry
- Refers to the relationship between the quantities of reactants and products before, during, and following chemical reactions. Stoichiometry is founded on the law of conservation of mass where the total mass of the reactants equals the total mass of the products, leading to the insight that the relations among quantities of reactants and products typically form a ratio of positive integers. This means that if the amounts of the separate reactants are known, then the amount of the product can be calculated. Conversely, if one reactant has a known quantity and the quantity of the products can be empirically determined, then the amount of the other reactants can also be calculated.
- Strain
- .
- Strain hardening
- Work hardening, also known as strain hardening, is the strengthening of a metal or polymer by plastic deformation. Work hardening may be desirable, undesirable, or inconsequential, depending on the context. This strengthening occurs because of dislocation movements and dislocation generation within the crystal structure of the material.[434] Many non-brittle metals with a reasonably high melting point as well as several polymers can be strengthened in this fashion.[435] Alloys not amenable to heat treatment, including low-carbon steel, are often work-hardened. Some materials cannot be work-hardened at low temperatures, such as indium,[436] however others can be strengthened only via work hardening, such as pure copper and aluminum.[437]
- Strength of materials
- The field of strength of materials, also called mechanics of materials, typically refers to various methods of calculating the stresses and strains in structural members, such as beams, columns, and shafts. The methods employed to predict the response of a structure under loading and its susceptibility to various failure modes takes into account the properties of the materials such as its yield strength, ultimate strength, Young's modulus, and Poisson's ratio. In addition, the mechanical element's macroscopic properties (geometric properties) such as its length, width, thickness, boundary constraints and abrupt changes in geometry such as holes are considered.
- Stress
- In continuum mechanics, stress is a physical quantity that expresses the internal forces that neighbouring particles of a continuous material exert on each other, while strain is the measure of the deformation of the material. For example, when a solid vertical bar is supporting an overhead weight, each particle in the bar pushes on the particles immediately below it. When a liquid is in a closed container under pressure, each particle gets pushed against by all the surrounding particles. The container walls and the pressure-inducing surface (such as a piston) push against them in (Newtonian) reaction. These macroscopic forces are actually the net result of a very large number of intermolecular forces and collisions between the particles in those molecules. Stress is frequently represented by a lowercase Greek letter sigma (σ).
- Stress–strain analysis
- Stress–strain analysis (or stress analysis) is an engineering discipline that uses many methods to determine the stresses and strains in materials and structures subjected to forces. In continuum mechanics, stress is a physical quantity that expresses the internal forces that neighboring particles of a continuous material exert on each other, while strain is the measure of the deformation of the material. In simple terms we can define stress as the force of resistance per unit per unit area, offered by a body against deformation. Stress is the ratio of force over area (S =R/A, where S is the stress, R is the internal resisting force and A is the cross-sectional area). Strain is the ratio of change in length to the original length, when a given body is subjected to some external force (Strain= change in length÷the original length).
- Stress–strain curve
- In engineering and materials science, a stress–strain curve for a material gives the relationship between stress and strain. It is obtained by gradually applying load to a test coupon and measuring the deformation, from which the stress and strain can be determined (see tensile testing). These curves reveal many of the properties of a material, such as the Young's modulus, the yield strength and the ultimate tensile strength.
- Structural analysis
- Is the determination of the effects of loads on physical structures and their components. Structures subject to this type of analysis include all that must withstand loads, such as buildings, bridges, aircraft and ships. Structural analysis employs the fields of applied mechanics, materials science and applied mathematics to compute a structure's deformations, internal forces, stresses, support reactions, accelerations, and stability. The results of the analysis are used to verify a structure's fitness for use, often precluding physical tests. Structural analysis is thus a key part of the engineering design of structures.[438]
- Structural load
- A structural load or structural action is a force, deformation, or acceleration applied to structural elements.[439][440] A load causes stress, deformation, and displacement in a structure. Structural analysis, a discipline in engineering, analyzes the effects loads on structures and structural elements. Excess load may cause structural failure, so this should be considered and controlled during the design of a structure. Particular mechanical structures—such as aircraft, satellites, rockets, space stations, ships, and submarines—are subject to their own particular structural loads and actions.[441] Engineers often evaluate structural loads based upon published regulations, contracts, or specifications. Accepted technical standards are used for acceptance testing and inspection.
- Sublimation
- Is the transition of a substance directly from the solid to the gas state,[442] without passing through the liquid state.[443] Sublimation is an endothermic process that occurs at temperatures and pressures below a substance's triple point in its phase diagram, which corresponds to the lowest pressure at which the substance can exist as a liquid. The reverse process of sublimation is deposition or desublimation, in which a substance passes directly from a gas to a solid phase.[444] Sublimation has also been used as a generic term to describe a solid-to-gas transition (sublimation) followed by a gas-to-solid transition (deposition).[445] While vaporization from liquid to gas occurs as evaporation from the surface if it occurs below the boiling point of the liquid, and as boiling with formation of bubbles in the interior of the liquid if it occurs at the boiling point, there is no such distinction for the solid-to-gas transition which always occurs as sublimation from the surface.
- Subsumption architecture
- Is a reactive robotic architecture heavily associated with behavior-based robotics which was very popular in the 1980s and 90s. The term was introduced by Rodney Brooks and colleagues in 1986.[446][447][448] Subsumption has been widely influential in autonomous robotics and elsewhere in real-time AI.
- Surface tension
- Is the tendency of liquid surfaces at rest to shrink into the minimum surface area possible. Surface tension is what allows objects with a higher density than water to float on a water surface without becoming even partly submerged.
- Superconductivity
- Is a set of physical properties observed in certain materials where electrical resistance vanishes and magnetic flux fields are expelled from the material. Any material exhibiting these properties is a superconductor. Unlike an ordinary metallic conductor, whose resistance decreases gradually as its temperature is lowered even down to near absolute zero, a superconductor has a characteristic critical temperature below which the resistance drops abruptly to zero. An electric current through a loop of superconducting wire can persist indefinitely with no power source.[449][450][451][452]
- Superhard material
- Is a material with a hardness value exceeding 40 gigapascals (GPa) when measured by the Vickers hardness test.[453][454][455][456] They are virtually incompressible solids with high electron density and high bond covalency. As a result of their unique properties, these materials are of great interest in many industrial areas including, but not limited to, abrasives, polishing and cutting tools, disc brakes, and wear-resistant and protective coatings.
- Supersaturation
- Supersaturation occurs with a chemical solution when the concentration of a solute exceeds the concentration specified by the value equilibrium solubility. Most commonly the term is applied to a solution of a solid in a liquid. A supersaturated solution is in a metastable state; it may be brought to equilibrium by forcing the excess of solute to separate from the solution. The term can also be applied to a mixture of gases.
T[]
- Tangential acceleration
- The velocity of a particle moving on a curved path as a function of time can be written as:
- Technical standard
- A technical standard is an established norm or requirement for a repeatable technical task. It is usually a formal document that establishes uniform engineering or technical criteria, methods, processes, and practices. In contrast, a custom, convention, company product, corporate standard, and so forth that becomes generally accepted and dominant is often called a de facto standard.
- Temperature
- Is a physical quantity that expresses hot and cold. It is the manifestation of thermal energy, present in all matter, which is the source of the occurrence of heat, a flow of energy, when a body is in contact with another that is colder. Temperature is measured with a thermometer. Thermometers are calibrated in various temperature scales that historically have used various reference points and thermometric substances for definition. The most common scales are the Celsius scale (formerly called centigrade, denoted °C), the Fahrenheit scale (denoted °F), and the Kelvin scale (denoted K), the last of which is predominantly used for scientific purposes by conventions of the International System of Units (SI).
- Tempering (metallurgy)
- Heat treatment to alter the crystal structure of a metal such as steel.
- Tensile force
- Pulling force, tending to lengthen an object.
- Tensile modulus
- Young's modulus , the Young modulus, or the modulus of elasticity in tension, is a mechanical property that measures the tensile stiffness of a solid material. It quantifies the relationship between tensile stress (force per unit area) and axial strain (proportional deformation) in the linear elastic region of a material and is determined using the formula:[460]
Young's moduli are typically so large that they are expressed not in pascals but in gigapascals (GPa).
- Tensile strength
- Ultimate tensile strength (UTS), often shortened to tensile strength (TS), ultimate strength, or within equations,[461][462][463] is the maximum stress that a material can withstand while being stretched or pulled before breaking. In brittle materials the ultimate tensile strength is close to the yield point, whereas in ductile materials the ultimate tensile strength can be higher.
- Tensile testing
- Tensile testing, also known as tension testing,[464] is a fundamental materials science and engineering test in which a sample is subjected to a controlled tension until failure. Properties that are directly measured via a tensile test are ultimate tensile strength, breaking strength, maximum elongation and reduction in area.[465] From these measurements the following properties can also be determined: Young's modulus, Poisson's ratio, yield strength, and strain-hardening characteristics.[466] Uniaxial tensile testing is the most commonly used for obtaining the mechanical characteristics of isotropic materials. Some materials use biaxial tensile testing. The main difference between these testing machines being how load is applied on the materials.
- Tension member
- Tension members are structural elements that are subjected to axial tensile forces. Examples of tension members are bracing for buildings and bridges, truss members, and cables in suspended roof systems.
- Thermal conduction
- Is the transfer of internal energy by microscopic collisions of particles and movement of electrons within a body. The colliding particles, which include molecules, atoms and electrons, transfer disorganized microscopic kinetic and potential energy, jointly known as internal energy. Conduction takes place in all phases: solid, liquid, and gas.
- Thermal equilibrium
- Two physical systems are in thermal equilibrium if there is no net flow of thermal energy between them when they are connected by a path permeable to heat. Thermal equilibrium obeys the zeroth law of thermodynamics. A system is said to be in thermal equilibrium with itself if the temperature within the system is spatially uniform and temporally constant. Systems in thermodynamic equilibrium are always in thermal equilibrium, but the converse is not always true. If the connection between the systems allows transfer of energy as 'change in internal energy' but does not allow transfer of matter or transfer of energy as work, the two systems may reach thermal equilibrium without reaching thermodynamic equilibrium.
- Thermal radiation
- Is electromagnetic radiation generated by the thermal motion of particles in matter. All matter with a temperature greater than absolute zero emits thermal radiation. Particle motion results in charge-acceleration or dipole oscillation which produces electromagnetic radiation.
- Thermodynamics
- Is a branch of physics that deals with heat, work, and temperature, and their relation to energy, radiation, and physical properties of matter. The behavior of these quantities is governed by the four laws of thermodynamics which convey a quantitative description using measurable macroscopic physical quantities, but may be explained in terms of microscopic constituents by statistical mechanics. Thermodynamics applies to a wide variety of topics in science and engineering, especially physical chemistry, biochemistry, chemical engineering and mechanical engineering, but also in other complex fields such as meteorology.
- Theory of relativity
- Usually encompasses two interrelated theories by Albert Einstein: special relativity and general relativity, proposed and published in 1905 and 1915, respectively.[467] Special relativity applies to all physical phenomena in the absence of gravity. General relativity explains the law of gravitation and its relation to other forces of nature.[468] It applies to the cosmological and astrophysical realm, including astronomy.[469]
- Thévenin's theorem
- As originally stated in terms of direct-current resistive circuits only, Thévenin's theorem states that "For any linear electrical network containing only voltage sources, current sources and resistances can be replaced at terminals A–B by an equivalent combination of a voltage source Vth in a series connection with a resistance Rth."
- The equivalent voltage Vth is the voltage obtained at terminals A–B of the network with terminals A–B open circuited.
- The equivalent resistance Rth is the resistance that the circuit between terminals A and B would have if all ideal voltage sources in the circuit were replaced by a short circuit and all ideal current sources were replaced by an open circuit.
- If terminals A and B are connected to one another, the current flowing from A to B will be Vth/Rth. This means that Rth could alternatively be calculated as Vth divided by the short-circuit current between A and B when they are connected together.
- Three-phase electric power
- Is a common method of alternating current electric power generation, transmission, and distribution.[470] It is a type of polyphase system and is the most common method used by electrical grids worldwide to transfer power. It is also used to power large motors and other heavy loads.
- Torque
- In physics and mechanics, torque is the rotational equivalent of linear force.[471] It is also referred to as the moment, moment of force, rotational force or turning effect, depending on the field of study. The concept originated with the studies by Archimedes of the usage of levers. Just as a linear force is a push or a pull, a torque can be thought of as a twist to an object around a specific axis. Another definition of torque is the product of the magnitude of the force and the perpendicular distance of the line of action of a force from the axis of rotation. The symbol for torque is typically or τ, the lowercase Greek letter tau. When being referred to as moment of force, it is commonly denoted by M.
- Torsional vibration
- Is angular vibration of an object—commonly a shaft along its axis of rotation. Torsional vibration is often a concern in power transmission systems using rotating shafts or couplings where it can cause failures if not controlled. A second effect of torsional vibrations applies to passenger cars. Torsional vibrations can lead to seat vibrations or noise at certain speeds. Both reduce the comfort.
- Toughness
- In materials science and metallurgy, toughness is the ability of a material to absorb energy and plastically deform without fracturing.[472] One definition of material toughness is the amount of energy per unit volume that a material can absorb before rupturing. This measure of toughness is different from that used for fracture toughness, which describes load bearing capabilities of materials with flaws.[473] It is also defined as a material's resistance to fracture when stressed. Toughness requires a balance of strength and ductility.[472]
- Trajectory
- A trajectory or flight path is the path that an object with mass in motion follows through space as a function of time. In classical mechanics, a trajectory is defined by Hamiltonian mechanics via canonical coordinates; hence, a complete trajectory is defined by position and momentum, simultaneously. The mass might be a projectile or a satellite.[474] For example, it can be an orbit — the path of a planet, asteroid, or comet as it travels around a central mass. In control theory, a trajectory is a time-ordered set of states of a dynamical system (see e.g. Poincaré map). In discrete mathematics, a trajectory is a sequence of values calculated by the iterated application of a mapping to an element of its source.
- Transducer
- Is a device that converts energy from one form to another. Usually a transducer converts a signal in one form of energy to a signal in another.[475] Transducers are often employed at the boundaries of automation, measurement, and control systems, where electrical signals are converted to and from other physical quantities (energy, force, torque, light, motion, position, etc.). The process of converting one form of energy to another is known as transduction.[476]
- Transformer
- Is a passive component that transfers electrical energy from one electrical circuit to another circuit, or multiple circuits. A varying current in any one coil of the transformer produces a varying magnetic flux in the transformer's core, which induces a varying electromotive force across any other coils wound around the same core. Electrical energy can be transferred between separate coils without a metallic (conductive) connection between the two circuits. Faraday's law of induction, discovered in 1831, describes the induced voltage effect in any coil due to a changing magnetic flux encircled by the coil.
- Trigonometric functions
- In mathematics, the trigonometric functions (also called circular functions, angle functions or goniometric functions[477][478]) are real functions which relate an angle of a right-angled triangle to ratios of two side lengths. They are widely used in all sciences that are related to geometry, such as navigation, solid mechanics, celestial mechanics, geodesy, and many others. They are among the simplest periodic functions, and as such are also widely used for studying periodic phenomena through Fourier analysis. The trigonometric functions most widely used in modern mathematics are the sine, the cosine, and the tangent. Their reciprocals are respectively the cosecant, the secant, and the cotangent, which are less used. Each of these six trigonometric functions has a corresponding inverse function, and an analog among the hyperbolic functions.[479]
- Trigonometry
- Is a branch of mathematics that studies relationships between side lengths and angles of triangles. The field emerged in the Hellenistic world during the 3rd century BC from applications of geometry to astronomical studies.[480] The Greeks focused on the calculation of chords, while mathematicians in India created the earliest-known tables of values for trigonometric ratios (also called trigonometric functions) such as sine.[481]
- Trimean
- The trimean is a measure of a probability distribution's location defined as a weighted average of the distribution's median and its two quartiles
- Triple point
- In thermodynamics, the triple point of a substance is the temperature and pressure at which the three phases (gas, liquid, and solid) of that substance coexist in thermodynamic equilibrium.[482] It is that temperature and pressure at which the sublimation curve, fusion curve and the vaporisation curve meet. For example, the triple point of mercury occurs at a temperature of −38.83440 °C (−37.90192 °F) and a pressure of 0.165 mPa. In addition to the triple point for solid, liquid, and gas phases, a triple point may involve more than one solid phase, for substances with multiple polymorphs. Helium-4 is a special case that presents a triple point involving two different fluid phases (lambda point).[482]
- Trouton's rule
- Trouton's rule states that the entropy of vaporization is almost the same value, about 85–88 J/(K·mol), for various kinds of liquids at their boiling points.[483] The entropy of vaporization is defined as the ratio between the enthalpy of vaporization and the boiling temperature. It is named after Frederick Thomas Trouton.
It can be expressed as a function of the gas constant R:
U[]
- Ultimate tensile strength
- Ultimate tensile strength (UTS), often shortened to tensile strength (TS), ultimate strength, or Ftu within equations,[461][462][463] is the capacity of a material or structure to withstand loads tending to elongate, as opposed to compressive strength, which withstands loads tending to reduce size. In other words, tensile strength resists tension (being pulled apart), whereas compressive strength resists compression (being pushed together). Ultimate tensile strength is measured by the maximum stress that a material can withstand while being stretched or pulled before breaking. In the study of strength of materials, tensile strength, compressive strength, and shear strength can be analyzed independently.
- Uncertainty principle
- In quantum mechanics, the uncertainty principle (also known as Heisenberg's uncertainty principle) is any of a variety of mathematical inequalities[490] asserting a fundamental limit to the precision with which certain pairs of physical properties of a particle, known as complementary variables, such as position x and momentum p, can be known.
- Unicode
- A standard for the consistent encoding of textual characters.
- Unit vector
- In mathematics, a unit vector in a normed vector space is a vector (often a spatial vector) of length 1. A unit vector is often denoted by a lowercase letter with a circumflex, or "hat": (pronounced "i-hat"). The term direction vector is used to describe a unit vector being used to represent spatial direction, and such quantities are commonly denoted as d. .
- Unsaturated compound
- .
- Upthrust
- Buoyancy, or upthrust, is an upward force exerted by a fluid that opposes the weight of a partially or fully immersed object. In a column of fluid, pressure increases with depth as a result of the weight of the overlying fluid. Thus the pressure at the bottom of a column of fluid is greater than at the top of the column. Similarly, the pressure at the bottom of an object submerged in a fluid is greater than at the top of the object. The pressure difference results in a net upward force on the object. The magnitude of the force is proportional to the pressure difference, and (as explained by Archimedes' principle) is equivalent to the weight of the fluid that would otherwise occupy the submerged volume of the object, i.e. the displaced fluid.
- Utility frequency
- The utility frequency, (power) line frequency (American English) or mains frequency (British English) is the nominal frequency of the oscillations of alternating current (AC) in a wide area synchronous grid transmitted from a power station to the end-user. In large parts of the world this is 50 Hz, although in the Americas and parts of Asia it is typically 60 Hz. Current usage by country or region is given in the list of mains electricity by country.
V[]
- Vacuole
- Is a membrane-bound organelle which is present in plant and fungal cells and some protist, animal[491] and bacterial cells.[492] Vacuoles are essentially enclosed compartments which are filled with water containing inorganic and organic molecules including enzymes in solution, though in certain cases they may contain solids which have been engulfed. Vacuoles are formed by the fusion of multiple membrane vesicles and are effectively just larger forms of these.[493] The organelle has no basic shape or size; its structure varies according to the requirements of the cell.
- Vacuum
- An absence of mass in a volume.
- Valence
- In chemistry, the valence or valency of an element is a measure of its combining power with other atoms when it forms chemical compounds or molecules. The concept of valence developed in the second half of the 19th century and helped successfully explain the molecular structure of inorganic and organic compounds.[494] The quest for the underlying causes of valence led to the modern theories of chemical bonding, including the cubical atom (1902), Lewis structures (1916), valence bond theory (1927), molecular orbitals (1928), valence shell electron pair repulsion theory (1958), and all of the advanced methods of quantum chemistry.
- Valence band
- In solid-state physics, the valence band and conduction band are the bands closest to the Fermi level and thus determine the electrical conductivity of the solid. In non-metals, the valence band is the highest range of electron energies in which electrons are normally present at absolute zero temperature, while the conduction band is the lowest range of vacant electronic states. On a graph of the electronic band structure of a material, the valence band is located below the Fermi level, while the conduction band is located above it. The distinction between the valence and conduction bands is meaningless in metals, because conduction occurs in one or more partially filled bands that take on the properties of both the valence and conduction bands.
- Valence bond theory
- In chemistry, valence bond (VB) theory is one of the two basic theories, along with molecular orbital (MO) theory, that were developed to use the methods of quantum mechanics to explain chemical bonding. It focuses on how the atomic orbitals of the dissociated atoms combine to give individual chemical bonds when a molecule is formed. In contrast, molecular orbital theory has orbitals that cover the whole molecule.[495]
- Valence electron
- In chemistry and physics, a valence electron is an outer shell electron that is associated with an atom, and that can participate in the formation of a chemical bond if the outer shell is not closed; in a single covalent bond, both atoms in the bond contribute one valence electron in order to form a shared pair.
- Valence shell
- The valence shell is the set of orbitals which are energetically accessible for accepting electrons to form chemical bonds. For main group elements, the valence shell consists of the ns and np orbitals in the outermost electron shell. In the case of transition metals (the (n-1)d orbitals), and lanthanides and actinides (the (n-2)f and (n-1)d orbitals), the orbitals involved can also be in an inner electron shell. Thus, the shell terminology is a misnomer as there is no correspondence between the valence shell and any particular electron shell in a given element. A scientifically correct term would be valence orbital to refer to the energetically accessible orbitals of an element.
- Valve
- Is a device or natural object that regulates, directs or controls the flow of a fluid (gases, liquids, fluidized solids, or slurries) by opening, closing, or partially obstructing various passageways. Valves are technically fittings, but are usually discussed as a separate category. In an open valve, fluid flows in a direction from higher pressure to lower pressure. The word is derived from the Latin valva, the moving part of a door, in turn from volvere, to turn, roll.
- van der Waals equation
- In chemistry and thermodynamics, the Van der Waals equation (or Van der Waals equation of state; named after Dutch physicist Johannes Diderik van der Waals) is an equation of state that generalizes the ideal gas law based on plausible reasons that real gases do not act ideally. The ideal gas law treats gas molecules as point particles that interact with their containers but not each other, meaning they neither take up space nor change kinetic energy during collisions (i.e. all collisions are perfectly elastic).[496] The ideal gas law states that volume (V) occupied by n moles of any gas has a pressure (P) at temperature (T) in kelvins given by the following relationship, where R is the gas constant:
- van der Waals force
- In molecular physics, the Van der Waals force, named after Dutch physicist Johannes Diderik van der Waals, is a distance-dependent interaction between atoms or molecules. Unlike ionic or covalent bonds, these attractions do not result from a chemical electronic bond; they are comparatively weak and therefore more susceptible to disturbance. The Van der Waals force quickly vanishes at longer distances between interacting molecules.
- van 't Hoff equation
- Relates the change in the equilibrium constant, Keq, of a chemical reaction to the change in temperature, T, given the standard enthalpy change, ΔrH⊖, for the process. It was proposed by Dutch chemist Jacobus Henricus van 't Hoff in 1884 in his book Études de dynamique chimique (Studies in Dynamic Chemistry).[497] The Van 't Hoff equation has been widely utilized to explore the changes in state functions in a thermodynamic system. The Van 't Hoff plot, which is derived from this equation, is especially effective in estimating the change in enthalpy and entropy of a chemical reaction.
- van 't Hoff factor
- Is a measure of the effect of a solute on colligative properties such as osmotic pressure, relative lowering in vapor pressure, boiling-point elevation and freezing-point depression. The Van 't Hoff factor is the ratio between the actual concentration of particles produced when the substance is dissolved and the concentration of a substance as calculated from its mass. For most non-electrolytes dissolved in water, the Van 't Hoff factor is essentially 1. For most ionic compounds dissolved in water, the Van 't Hoff factor is equal to the number of discrete ions in a formula unit of the substance. This is true for ideal solutions only, as occasionally ion pairing occurs in solution. At a given instant a small percentage of the ions are paired and count as a single particle. Ion pairing occurs to some extent in all electrolyte solutions. This causes the measured Van 't Hoff factor to be less than that predicted in an ideal solution. The deviation for the Van 't Hoff factor tends to be greatest where the ions have multiple charges.
- Variable capacitor
- Is a capacitor whose capacitance may be intentionally and repeatedly changed mechanically or electronically. Variable capacitors are often used in L/C circuits to set the resonance frequency, e.g. to tune a radio (therefore it is sometimes called a tuning capacitor or tuning condenser), or as a variable reactance, e.g. for impedance matching in antenna tuners.
- Variable resistor
- .
- Vector space
- A vector space (also called a linear space) is a set of objects called vectors, which may be added together and multiplied ("scaled") by numbers, called scalars. Scalars are often taken to be real numbers, but there are also vector spaces with scalar multiplication by complex numbers, rational numbers, or generally any field. The operations of vector addition and scalar multiplication must satisfy certain requirements, called vector axioms . To specify that the scalars are real or complex numbers, the terms real vector space and complex vector space are often used.
- Venturi effect
- Is the reduction in fluid pressure that results when a fluid flows through a constricted section (or choke) of a pipe. The Venturi effect is named after its discoverer, the 18th century Italian physicist, Giovanni Battista Venturi.
- Vibration
- Is a mechanical phenomenon whereby oscillations occur about an equilibrium point. The word comes from Latin vibrationem ("shaking, brandishing"). The oscillations may be periodic, such as the motion of a pendulum—or random, such as the movement of a tire on a gravel road. Vibration can be desirable: for example, the motion of a tuning fork, the reed in a woodwind instrument or harmonica, a mobile phone, or the cone of a loudspeaker. In many cases, however, vibration is undesirable, wasting energy and creating unwanted sound. For example, the vibrational motions of engines, electric motors, or any mechanical device in operation are typically unwanted. Such vibrations could be caused by imbalances in the rotating parts, uneven friction, or the meshing of gear teeth. Careful designs usually minimize unwanted vibrations.
- Virtual leak
- Traces of gas trapped in cavities within a vacuum chamber, slowly dissipating out in the main chamber, thus appearing like a leak from the outside.
- Viscoelasticity
- In materials science and continuum mechanics, viscoelasticity is the property of materials that exhibit both viscous and elastic characteristics when undergoing deformation. Viscous materials, like water, resist shear flow and strain linearly with time when a stress is applied. Elastic materials strain when stretched and immediately return to their original state once the stress is removed. Viscoelastic materials have elements of both of these properties and, as such, exhibit time-dependent strain. Whereas elasticity is usually the result of bond stretching along crystallographic planes in an ordered solid, viscosity is the result of the diffusion of atoms or molecules inside an amorphous material.[498]
- Viscosity
- The viscosity of a fluid is the measure of its resistance to gradual deformation by shear stress or tensile stress.[499] For liquids, it corresponds to the informal concept of "thickness": for example, honey has a higher viscosity than water.[500]
- Volt-ampere
- (VA), is the unit used for the apparent power in an electrical circuit. The apparent power equals the product of root-mean-square (RMS) voltage and RMS current.[501] In direct current (DC) circuits, this product is equal to the real power (active power)[502] in watts. Volt-amperes are useful only in the context of alternating current (AC) circuits. The volt-ampere is dimensionally equivalent to the watt (in SI units, 1 VA = 1 N m A−1 s −1 A = 1 N m s −1 = 1 J s −1 = 1 W). VA rating is most useful in rating wires and switches (and other power handling equipment) for inductive loads.
- Volt-ampere reactive
- In electric power transmission and distribution, volt-ampere reactive (var) is a unit of measurement of reactive power. Reactive power exists in an AC circuit when the current and voltage are not in phase. The term var was proposed by the Romanian electrical engineer Constantin Budeanu and introduced in 1930 by the IEC in Stockholm, which has adopted it as the unit for reactive power. Special instruments called varmeters are available to measure the reactive power in a circuit.[418] The unit "var" is allowed by the International System of Units (SI) even though the unit var is representative of a form of power.[503] SI allows one to specify units to indicate common sense physical considerations. Per EU directive 80/181/EEC (the "metric directive"), the correct symbol is lower-case "var",[504] although the spellings "Var" and "VAr" are commonly seen, and "VAR" is widely used throughout the power industry.
- Volta potential
- The Volta potential (also called Volta potential difference, contact potential difference, outer potential difference, Δψ, or "delta psi") in electrochemistry, is the electrostatic potential difference between two metals (or one metal and one electrolyte) that are in contact and are in thermodynamic equilibrium. Specifically, it is the potential difference between a point close to the surface of the first metal, and a point close to the surface of the second metal (or electrolyte).[505]
- Voltage
- Voltage, electric potential difference, electric pressure or electric tension is the difference in electric potential between two points. The difference in electric potential between two points (i.e., voltage) is defined as the work needed per unit of charge against a static electric field to move a test charge between the two points. In the International System of Units, the derived unit for voltage is named volt.[506] In SI units, work per unit charge is expressed as joules per coulomb, where 1 volt = 1 joule (of work) per 1 coulomb (of charge). The official SI definition for volt uses power and current, where 1 volt = 1 watt (of power) per 1 ampere (of current).[506]
- Volumetric flow rate
- Also known as volume flow rate, rate of fluid flow or volume velocity, is the volume of fluid which passes per unit time; usually represented by the symbol Q (sometimes V̇). The SI unit is m3/s (cubic metres per second).
- von Mises yield criterion
- The von Mises yield criterion (also known as the maximum distortion energy criterion[507]) suggests that yielding of a ductile material begins when the second deviatoric stress invariant reaches a critical value.[508] It is part of plasticity theory that applies best to ductile materials, such as some metals. Prior to yield, material response can be assumed to be of a nonlinear elastic, viscoelastic, or linear elastic behavior. In materials science and engineering the von Mises yield criterion can also be formulated in terms of the von Mises stress or equivalent tensile stress, . This is a scalar value of stress that can be computed from the Cauchy stress tensor. In this case, a material is said to start yielding when the von Mises stress reaches a value known as yield strength, . The von Mises stress is used to predict yielding of materials under complex loading from the results of uniaxial tensile tests. The von Mises stress satisfies the property where two stress states with equal distortion energy have an equal von Mises stress.
W[]
- Watt
- The SI unit of power, rate of doing work.
- Wave
- Is a disturbance that transfers energy through matter or space, with little or no associated mass transport. Waves consist of oscillations or vibrations of a physical medium or a field, around relatively fixed locations. From the perspective of mathematics, waves, as functions of time and space, are a class of signals.[509]
- Wavelength
- Is the spatial period of a periodic wave—the distance over which the wave's shape repeats.[510][511] It is thus the inverse of the spatial frequency. Wavelength is usually determined by considering the distance between consecutive corresponding points of the same phase, such as crests, troughs, or zero crossings and is a characteristic of both traveling waves and standing waves, as well as other spatial wave patterns.[512][513] Wavelength is commonly designated by the Greek letter lambda (λ). The term wavelength is also sometimes applied to modulated waves, and to the sinusoidal envelopes of modulated waves or waves formed by interference of several sinusoids.[514]' .
- Wedge
- Is a triangular shaped tool, and is a portable inclined plane, and one of the six classical simple machines. It can be used to separate two objects or portions of an object, lift up an object, or hold an object in place. It functions by converting a force applied to its blunt end into forces perpendicular (normal) to its inclined surfaces. The mechanical advantage of a wedge is given by the ratio of the length of its slope to its width.[515][516] Although a short wedge with a wide angle may do a job faster, it requires more force than a long wedge with a narrow angle.
- Weighted arithmetic mean
- The weighted arithmetic mean is similar to an ordinary arithmetic mean (the most common type of average), except that instead of each of the data points contributing equally to the final average, some data points contribute more than others. The notion of weighted mean plays a role in descriptive statistics and also occurs in a more general form in several other areas of mathematics. If all the weights are equal, then the weighted mean is the same as the arithmetic mean. While weighted means generally behave in a similar fashion to arithmetic means, they do have a few counterintuitive properties, as captured for instance in Simpson's paradox.
- Wet-bulb temperature
- The temperature of a wetted thermometer with an air current across it. Used in psychrometry.
- Wheel and axle
- Are one of six simple machines identified by Renaissance scientists drawing from Greek texts on technology.[517] The wheel and axle consists of a wheel attached to a smaller axle so that these two parts rotate together in which a force is transferred from one to the other. A hinge or bearing supports the axle, allowing rotation. It can amplify force; a small force applied to the periphery of the large wheel can move a larger load attached to the axle.
- Winsorized mean
- Is a winsorized statistical measure of central tendency, much like the mean and median, and even more similar to the truncated mean. It involves the calculation of the mean after replacing given parts of a probability distribution or sample at the high and low end with the most extreme remaining values,[518] typically doing so for an equal amount of both extremes; often 10 to 25 percent of the ends are replaced. The winsorized mean can equivalently be expressed as a weighted average of the truncated mean and the quantiles at which it is limited, which corresponds to replacing parts with the corresponding quantiles.
- Work hardening
- Also known as strain hardening, is the strengthening of a metal or polymer by plastic deformation. This strengthening occurs because of dislocation movements and dislocation generation within the crystal structure of the material.[519]
X-Z[]
- X-axis
- In algebraic geometry, the axis on a graph that is usually drawn left to right and usually shows the range of values of an independent variable.[520]
- Y-axis
- In algebraic geometry, the axis on a graph that is usually drawn from bottom to top and usually shows the range of values of variable dependent on one other variable, or the second of two independent variables.[521]
- Yield
- The point of maximum elastic deformation of a material; above yield the material is permanently deformed.
- Young's modulus
- A measure of the stiffness of a material; the amount of force per unit area require to produce a unit strain.
- Z-axis
- In algebraic geometry, the axis on a graph of at least three dimensions that is usually drawn vertically and usually shows the range of values of a variable dependent on two other variables or the third independent variable.[522]
- Zero defects
- A quality assurance philosophy that aims to reduce the need for inspection of components by improving their quality.
- Zero force member
- In the field of engineering mechanics, a zero force member is a member (a single truss segment) in a truss which, given a specific load, is at rest: neither in tension, nor in compression. In a truss a zero force member is often found at pins (any connections within the truss) where no external load is applied and three or fewer truss members meet. Recognizing basic zero force members can be accomplished by analyzing the forces acting on an individual pin in a physical system.
NOTE: If the pin has an external force or moment applied to it, then all of the members attached to that pin are not zero force members UNLESS the external force acts in a manner that fulfills one of the rules below:
- If two non-collinear members meet in an unloaded joint, both are zero-force members.
- If three members meet in an unloaded joint of which two are collinear, then the third member is a zero-force member.
- These members contribute to the stability of the structure, by providing buckling prevention for long slender members under compressive forces
- These members can carry loads in the event that variations are introduced in the normal external loading configuration.
- Zeroth law of thermodynamics
- The equivalence principle applied to temperature; two systems in thermal equiplbirum with a third are also in thermal equilibrium with each other.
See also[]
- Engineering
- National Council of Examiners for Engineering and Surveying
- Fundamentals of Engineering Examination
- Principles and Practice of Engineering Examination
- Graduate Aptitude Test in Engineering
- Glossary of aerospace engineering
- Glossary of civil engineering
- Glossary of electrical and electronics engineering
- Glossary of mechanical engineering
- Glossary of structural engineering
- Glossary of architecture
- Glossary of areas of mathematics
- Glossary of artificial intelligence
- Glossary of astronomy
- Glossary of biology
- Glossary of calculus
- Glossary of chemistry
- Glossary of ecology
- Glossary of economics
- Glossary of physics
- Glossary of probability and statistics
- List of established military terms § Engineering
Notes[]
- ^ The second law of thermodynamics imposes limitations on the capacity of a system to transfer energy by performing work, since some of the system's energy might necessarily be consumed in the form of heat instead. See e.g. Lehrman, Robert L. (1973). "Energy Is Not The Ability To Do Work". The Physics Teacher. 11 (1): 15–18. Bibcode:1973PhTea..11...15L. doi:10.1119/1.2349846. ISSN 0031-921X.
- ^ The words map, mapping, transformation, correspondence, and operator are often used synonymously. Halmos 1970, p. 30 .
- ^ Strictly speaking, a probability of 0 indicates that an event almost never takes place, whereas a probability of 1 indicates than an event almost certainly takes place. This is an important distinction when the sample space is infinite. For example, for the continuous uniform distribution on the real interval [5, 10], there are an infinite number of possible outcomes, and the probability of any given outcome being observed — for instance, exactly 7 — is 0. This means that when we make an observation, it will almost surely not be exactly 7. However, it does not mean that exactly 7 is impossible. Ultimately some specific outcome (with probability 0) will be observed, and one possibility for that specific outcome is exactly 7.
- ^ "Newtonian constant of gravitation" is the name introduced for G by Boys (1894). Use of the term by T.E. Stern (1928) was misquoted as "Newton's constant of gravitation" in Pure Science Reviewed for Profound and Unsophisticated Students (1930), in what is apparently the first use of that term. Use of "Newton's constant" (without specifying "gravitation" or "gravity") is more recent, as "Newton's constant" was also used for the heat transfer coefficient in Newton's law of cooling, but has by now become quite common, e.g. Calmet et al, Quantum Black Holes (2013), p. 93; P. de Aquino, Beyond Standard Model Phenomenology at the LHC (2013), p. 3. The name "Cavendish gravitational constant", sometimes "Newton–Cavendish gravitational constant", appears to have been common in the 1970s to 1980s, especially in (translations from) Soviet-era Russian literature, e.g. Sagitov (1970 [1969]), Soviet Physics: Uspekhi 30 (1987), Issues 1–6, p. 342 [etc.]. "Cavendish constant" and "Cavendish gravitational constant" is also used in Charles W. Misner, Kip S. Thorne, John Archibald Wheeler, "Gravitation", (1973), 1126f. Colloquial use of "Big G", as opposed to "little g" for gravitational acceleration dates to the 1960s (R.W. Fairbridge, The encyclopedia of atmospheric sciences and astrogeology, 1967, p. 436; note use of "Big G's" vs. "little g's" as early as the 1940s of the Einstein tensor Gμν vs. the metric tensor gμν, Scientific, medical, and technical books published in the United States of America: a selected list of titles in print with annotations: supplement of books published 1945–1948, Committee on American Scientific and Technical Bibliography National Research Council, 1950, p. 26).
- ^ Integral calculus is a very well established mathematical discipline for which there are many sources. See Apostol 1967 and Anton, Bivens & Davis 2016 , for example.
- ^ The photon's invariant mass (also called "rest mass" for massive particles) is believed to be exactly zero. This is the notion of particle mass generally used by modern physicists. The photon does have a nonzero relativistic mass, depending on its energy, but this varies according to the frame of reference.
- ^ At the start of The Feynman Lectures on Physics, Richard Feynman offers the atomic hypothesis as the single most prolific scientific concept.[352]
- ^ The term "universe" is defined as everything that physically exists: the entirety of space and time, all forms of matter, energy and momentum, and the physical laws and constants that govern them. However, the term "universe" may also be used in slightly different contextual senses, denoting concepts such as the cosmos or the philosophical world.
- ^ The preferred spelling varies by country and even by industry. Further, both spellings are often used within a particular industry or country. Industries in British English-speaking countries typically use the "gauge" spelling.
- ^ For example, the SI unit of velocity is the metre per second, m⋅s−1; of acceleration is the metre per second squared, m⋅s−2; etc.
- ^ For example the newton (N), the unit of force, equivalent to kg⋅m⋅s−2; the joule (J), the unit of energy, equivalent to kg⋅m2⋅s−2, etc. The most recently named derived unit, the katal, was defined in 1999.
- ^ For example, the recommended unit for the electric field strength is the volt per metre, V/m, where the volt is the derived unit for electric potential difference. The volt per metre is equal to kg⋅m⋅s−3⋅A−1 when expressed in terms of base units.
- ^ For example, the SI unit of velocity is the metre per second, m⋅s−1; of acceleration is the metre per second squared, m⋅s−2; etc.
- ^ For example the newton (N), the unit of force, equivalent to kg⋅m⋅s−2; the joule (J), the unit of energy, equivalent to kg⋅m2⋅s−2, etc. The most recently named derived unit, the katal, was defined in 1999.
- ^ For example, the recommended unit for the electric field strength is the volt per metre, V/m, where the volt is the derived unit for electric potential difference. The volt per metre is equal to kg⋅m⋅s−3⋅A−1 when expressed in terms of base units.
References[]
- ^ IUPAC Gold Book - absolute electrode potential
- ^ "Unit of thermodynamic temperature (kelvin)". SI Brochure, 8th edition. Bureau International des Poids et Mesures. 13 March 2010 [1967]. Section 2.1.1.5. Archived from the original on 7 October 2014. Retrieved 20 June 2017. Note: The triple point of water is 0.01 °C, not 0 °C; thus 0 K is −273.15 °C, not −273.16 °C.
- ^ Arora, C. P. (2001). Thermodynamics. Tata McGraw-Hill. Table 2.4 page 43. ISBN 978-0-07-462014-4.
- ^ Zielinski, Sarah (1 January 2008). "Absolute Zero". Smithsonian Institution. Retrieved 2012-01-26.
- ^ IUPAC, Compendium of Chemical Terminology, 2nd ed. (the "Gold Book") (1997). Online corrected version: (2006–) "Absorbance". doi:10.1351/goldbook.A00028
- ^ IUPAC Gold Book - acid
- ^ Knowles, J. R. (1980). "Enzyme-catalyzed phosphoryl transfer reactions". Annu. Rev. Biochem. 49: 877–919. doi:10.1146/annurev.bi.49.070180.004305. PMID 6250450.
- ^ "Aerobic Diestion" (PDF). Water Environment Federation. Archived from the original (PDF) on 27 March 2016. Retrieved 19 March 2016.
- ^ "Handbook Biological Wastewater Treatment - Design of Activated Sludge Systems". Retrieved 19 March 2016.
- ^ Encyclopedia of Aerospace Engineering. John Wiley & Sons, 2010. ISBN 978-0-470-75440-5.
- ^ Daniel Malacara, Zacarias Malacara, Handbook of optical design. Page 379
- ^ "Alkanes". IUPAC Gold Book - alkanes. IUPAC. March 27, 2017. doi:10.1351/goldbook.A00222. ISBN 978-0-9678550-9-7. Retrieved 2018-08-23.
- ^ Wade, L.G. (2006). Organic Chemistry (6th ed.). Pearson Prentice Hall. p. 279. ISBN 978-1-4058-5345-3.
- ^ Alkyne. Encyclopædia Britannica
- ^ Callister, W. D. "Materials Science and Engineering: An Introduction" 2007, 7th edition, John Wiley and Sons, Inc. New York, Section 4.3 and Chapter 9.
- ^ "Amino". Dictionary.com. 2015. Retrieved 3 July 2015.
- ^ "amino acid". Cambridge Dictionaries Online. Cambridge University Press. 2015. Retrieved 3 July 2015.
- ^ "amino". FreeDictionary.com. Farlex. 2015. Retrieved 3 July 2015.
- ^ Wagner I, Musso H (November 1983). "New Naturally Occurring Amino Acids". Angewandte Chemie International Edition in English. 22 (11): 816–28. doi:10.1002/anie.198308161.
- ^ IUPAC, Compendium of Chemical Terminology, 2nd ed. (the "Gold Book") (1997). Online corrected version: (2006–) "amphoteric". doi:10.1351/goldbook.A00306
- ^ Knopp, Konrad; Bagemihl, Frederick (1996). Theory of Functions Parts I and II. Dover Publications. p. 3. ISBN 978-0-486-69219-7.
- ^ National Non-Food Crops Centre. "NNFCC Renewable Fuels and Energy Factsheet: Anaerobic Digestion", Retrieved on 2011-11-22
- ^ "Angular Velocity and Acceleration". Theory.uwinnipeg.ca. Archived from the original on 2012-02-22. Retrieved 2015-04-13.
- ^ University of Colorado Boulder (November 21, 2013). "Atoms and Elements, Isotopes and Ions". colorado.edu.
- ^ "Antimatter". Lawrence Berkeley National Laboratory. Archived from the original on 23 August 2008. Retrieved 3 September 2008.
- ^ "The Standard Model – Particle decays and annihilations". The Particle Adventure: The Fundamentals of Matter and Force. Lawrence Berkeley National Laboratory. Retrieved 17 October 2011.
- ^ RFC 4949
- ^ "ATMAE Venn Diagram". Archived from the original on 2017-06-30. Retrieved 2018-11-15.
- ^ "What is buoyant force?".
- ^ Jump up to: a b Acott, Chris (1999). "The diving "Law-ers": A brief resume of their lives". South Pacific Underwater Medicine Society Journal. 29 (1). ISSN 0813-1988. OCLC 16986801. Archived from the original on 2011-04-02. Retrieved 2011-06-14..
- ^ Jacobs, Harold R. (1994). Mathematics: A Human Endeavor (Third ed.). W. H. Freeman. p. 547. ISBN 978-0-7167-2426-1.
- ^ IUPAC, Compendium of Chemical Terminology, 2nd ed. (the "Gold Book") (1997). Online corrected version: (2006–) "arenes". doi:10.1351/goldbook.A00435
- ^ Mechanisms of Activation of the Aryl Hydrocarbon Receptor by Maria Backlund, Institute of Environmental Medicine, Karolinska Institutet.
- ^ Arrhenius, S.A. (1889). "Über die Dissociationswärme und den Einfluß der Temperatur auf den Dissociationsgrad der Elektrolyte". Z. Phys. Chem. 4: 96–116. doi:10.1515/zpch-1889-0408. S2CID 202553486.
- ^ Arrhenius, S.A. (1889). "Über die Reaktionsgeschwindigkeit bei der Inversion von Rohrzucker durch Säuren". ibid. 4: 226–248.
- ^ Laidler, K. J. (1987) Chemical Kinetics, Third Edition, Harper & Row, p.42
- ^ Kenneth Connors, Chemical Kinetics, 1990, VCH Publishers Chemical Kinetics: The Study of Reaction Rates in Solution at Google Books
- ^ Poole, Mackworth & Goebel 1998, p. 1.
- ^ Russell & Norvig 2003, p. 55.
- ^ Definition of AI as the study of intelligent agents:
- Poole, Mackworth & Goebel (1998) , which provides the version that is used in this article. These authors use the term "computational intelligence" as a synonym for artificial intelligence.[38]
- Russell & Norvig (2003) (who prefer the term "rational agent") and write "The whole-agent view is now widely accepted in the field".[39]
- Nilsson 1998
- Legg & Hutter 2007
- ^ Russell & Norvig 2009, p. 2.
- ^ Orchin, Milton; Macomber, Roger S.; Pinhas, Allan; Wilson, R. Marshall (2005). Atomic Orbital Theory (PDF).
- ^ Daintith, J. (2004). Oxford Dictionary of Chemistry. New York: Oxford University Press. ISBN 978-0-19-860918-6.
- ^ Pilhofer, Michael (2007). Music Theory for Dummies. For Dummies. p. 97. ISBN 9780470167946.
- ^ Nichols R (Jul 2001). "Quenching and tempering of welded carbon steel tubulars".
- ^ Lambers HG, Tschumak S, Maier HJ, Canadinc D (Apr 2009). "Role of Austenitization and Pre-Deformation on the Kinetics of the Isothermal Bainitic Transformation". Metall. Mater. Trans. A. 40 (6): 1355–1366. Bibcode:2009MMTA..tmp...74L. doi:10.1007/s11661-009-9827-z. S2CID 136882327.
- ^ "Austenitization".
- ^ Groover, Mikell (2014). Fundamentals of Modern Manufacturing: Materials, Processes, and Systems.
- ^ Rifkin, Jeremy (1995). The End of Work: The Decline of the Global Labor Force and the Dawn of the Post-Market Era. Putnam Publishing Group. pp. 66, 75. ISBN 978-0-87477-779-6.
- ^ Johll, Matthew E. (2009). Investigating chemistry: a forensic science perspective (2nd ed.). New York: W. H. Freeman and Co. ISBN 978-1429209892. OCLC 392223218.
- ^ Attaway, Stephen W. (1999). The Mechanics of Friction in Rope Rescue (PDF). International Technical Rescue Symposium. Retrieved February 1, 2010.
- ^ Boresi, A. P. and Schmidt, R. J. and Sidebottom, O. M., 1993, Advanced mechanics of materials, John Wiley and Sons, New York.
- ^ Gere, J.M.; Timoshenko, S.P. (1996), Mechanics of Materials:Forth edition, Nelson Engineering, ISBN 0534934293
- ^ Beer, F.; Johnston, E.R. (1984), Vector mechanics for engineers: statics, McGraw Hill, pp. 62–76
- ^ David, Rodreck; Ngulube, Patrick; Dube, Adock (16 July 2013). "A cost-benefit analysis of document management strategies used at a financial institution in Zimbabwe: A case study". SA Journal of Information Management. 15 (2). doi:10.4102/sajim.v15i2.540.
- ^ Weisstein, Eric W. "Bernoulli Differential Equation." From MathWorld--A Wolfram Web Resource. http://mathworld.wolfram.com/BernoulliDifferentialEquation.html
- ^ Clancy, L. J. (1975). Aerodynamics. Wiley. ISBN 978-0-470-15837-1.
- ^ Batchelor, G. K. (2000). An Introduction to Fluid Dynamics. Cambridge: University Press. ISBN 978-0-521-66396-0.
- ^ "Hydrodynamica". Britannica Online Encyclopedia. Retrieved 2008-10-30.
- ^ Anderson, J.D. (2016), "Some reflections on the history of fluid dynamics", in Johnson, R.W. (ed.), Handbook of fluid dynamics (2nd ed.), CRC Press, ISBN 9781439849576
- ^ Darrigol, O.; Frisch, U. (2008), "From Newton's mechanics to Euler's equations", Physica D: Nonlinear Phenomena, 237 (14–17): 1855–1869, Bibcode:2008PhyD..237.1855D, doi:10.1016/j.physd.2007.08.003
- ^ Lawrence Berkeley National Laboratory (9 August 2000). "Beta Decay". Nuclear Wall Chart. United States Department of Energy. Retrieved 17 January 2016.
- ^ Anthonsen, Thorlief (2000). "Reactions Catalyzed by Enzymes". In Adlercreutz, Patrick; Straathof, Adrie J. J. (eds.). Applied Biocatalysis (2nd ed.). Taylor & Francis. pp. 18–59. ISBN 978-9058230249. Retrieved 9 February 2013.
- ^ Faber, Kurt (2011). Biotransformations in Organic Chemistry (6th ed.). Springer. ISBN 9783642173936.[page needed]
- ^ Jayasinghe, Leonard Y.; Smallridge, Andrew J.; Trewhella, Maurie A. (1993). "The yeast mediated reduction of ethyl acetoacetate in petroleum ether". Tetrahedron Letters. 34 (24): 3949–3950. doi:10.1016/S0040-4039(00)79272-0.
- ^ John Denis Enderle; Joseph D. Bronzino (2012). Introduction to Biomedical Engineering. Academic Press. pp. 16–. ISBN 978-0-12-374979-6.
- ^ Vincent, Julian F. V.; et al. (22 August 2006). "Biomimetics: its practice and theory". Journal of the Royal Society Interface. 3 (9): 471–482. doi:10.1098/rsif.2006.0127. PMC 1664643. PMID 16849244.
- ^ "Biophysics | science". Encyclopædia Britannica. Retrieved 2018-07-26.
- ^ Zhou HX (March 2011). "Q&A: What is biophysics?". BMC Biology. 9: 13. doi:10.1186/1741-7007-9-13. PMC 3055214. PMID 21371342.
- ^ "the definition of biophysics". www.dictionary.com. Retrieved 2018-07-26.
- ^ Frederick M. Steingress (2001). Low Pressure Boilers (4th ed.). American Technical Publishers. ISBN 0-8269-4417-5.
- ^ Frederick M. Steingress, Harold J. Frost and Darryl R. Walker (2003). High Pressure Boilers (3rd ed.). American Technical Publishers. ISBN 0-8269-4300-4.
- ^ Goldberg, David E. (1988). 3,000 Solved Problems in Chemistry (1st ed.). McGraw-Hill. section 17.43, p. 321. ISBN 0-07-023684-4.
- ^ Theodore, Louis; Dupont, R. Ryan; Ganesan, Kumar, eds. (1999). Pollution Prevention: The Waste Management Approach to the 21st Century. CRC Press. section 27, p. 15. ISBN 1-56670-495-2.
- ^ Richard Feynman (1970). The Feynman Lectures on Physics Vol I. Addison Wesley Longman. ISBN 978-0-201-02115-8.
- ^ Wells, John C. (1990). Longman pronunciation dictionary. Harlow, England: Longman. ISBN 978-0582053830. entry "Boson"
- ^ "boson". Collins Dictionary.
- ^ Carroll, Sean (2007). Guidebook. Dark Matter, Dark Energy: The dark side of the universe. The Teaching Company. Part 2, p. 43. ISBN 978-1598033502.
... boson: A force-carrying particle, as opposed to a matter particle (fermion). Bosons can be piled on top of each other without limit. Examples include photons, gluons, gravitons, weak bosons, and the Higgs boson. The spin of a boson is always an integer, such as 0, 1, 2, and so on ...
- ^ Notes on Dirac's lecture Developments in Atomic Theory at Le Palais de la Découverte, 6 December 1945. UKNATARCHI Dirac Papers. BW83/2/257889.
- ^ Farmelo, Graham (2009-08-25). The Strangest Man: The Hidden Life of Paul Dirac, Mystic of the Atom. Basic Books. p. 331. ISBN 9780465019922.
- ^ Daigle, Katy (10 July 2012). "India: Enough about Higgs, let's discuss the boson". AP News. Retrieved 10 July 2012.
- ^ Bal, Hartosh Singh (19 September 2012). "The Bose in the Boson". The New York Times blog. Retrieved 21 September 2012.
- ^ "Higgs boson: The poetry of subatomic particles". BBC News. 4 July 2012. Retrieved 6 July 2012.
- ^ Draper, John William (1861). A Textbook on chemistry. Harper & Bros. p. 46.
draper, john william.
- ^ Levine, Ira. N (1978). "Physical Chemistry" University of Brooklyn: McGraw-Hill
- ^ Levine, Ira. N. (1978), p. 12 gives the original definition.
- ^ Aroyo, Mois I.; Müller, Ulrich; Wondratschek, Hans (2006). "Historical Introduction". International Tables for Crystallography. A1 (1.1): 2–5. CiteSeerX 10.1.1.471.4170. doi:10.1107/97809553602060000537. Archived from the original on 2013-07-04. Retrieved 2008-04-21.
- ^ Levine, David; Michele Boldrin (2008-09-07). Against Intellectual Monopoly. Cambridge University Press. p. 312. ISBN 978-0-521-87928-6.
- ^ Tapang, Bienvenido, and Lorelei Mendoza. Introductory Economics. University of the Philippines, Baguio.
- ^ David Brewster (1815) "On the laws which regulate the polarisation of light by reflection from transparent bodies," Philosophical Transactions of the Royal Society of London, 105: 125-159.
- ^ Lakhtakia, Akhlesh (June 1989). "Would Brewster recognize today's Brewster angle?" (PDF). Optics News. OSA. 15 (6): 14–18. doi:10.1364/ON.15.6.000014.
- ^ Brönsted, J. N. (1923). "Einige Bemerkungen über den Begriff der Säuren und Basen" [Some observations about the concept of acids and bases]. Recueil des Travaux Chimiques des Pays-Bas. 42 (8): 718–728. doi:10.1002/recl.19230420815.
- ^ Lowry, T. M. (1923). "The uniqueness of hydrogen". Journal of the Society of Chemical Industry. 42 (3): 43–47. doi:10.1002/jctb.5000420302.
- ^ Feynman, R. (1964). "The Brownian Movement". The Feynman Lectures of Physics, Volume I. pp. 41–1.
- ^ "Bulk Elastic Properties". hyperphysics. Georgia State University.
- ^ "Capillary Action – Liquid, Water, Force, and Surface – JRank Articles". Science.jrank.org. Archived from the original on 2013-05-27. Retrieved 2013-06-18.
- ^ Kimball's Biology pages Archived 2009-01-25 at the Wayback Machine, Cell Membranes
- ^ Singleton P (1999). Bacteria in Biology, Biotechnology and Medicine (5th ed.). New York: Wiley. ISBN 978-0-471-98880-9.
- ^ Weik, Martin H. (1961). "A Third Survey of Domestic Electronic Digital Computing Systems". Ballistic Research Laboratory.
- ^ Kuck, David (1978). Computers and Computations, Vol 1. John Wiley & Sons, Inc. p. 12. ISBN 978-0471027164.
- ^ Bornens, M.; Azimzadeh, J. (2008). "Origin and Evolution of the Centrosome". Eukaryotic Membranes and Cytoskeleton. Advances in Experimental Medicine and Biology. 607. pp. 119–129. doi:10.1007/978-0-387-74021-8_10. ISBN 978-0-387-74020-1. PMID 17977464.
- ^ Schmit (2002). Acentrosomal microtubule nucleation in higher plants. International Review of Cytology. 220. pp. 257–289. doi:10.1016/S0074-7696(02)20008-X. ISBN 9780123646248. PMID 12224551.
- ^ Jaspersen, S. L.; Winey, M. (2004). "THE BUDDING YEAST SPINDLE POLE BODY: Structure, Duplication, and Function". Annual Review of Cell and Developmental Biology. 20 (1): 1–28. doi:10.1146/annurev.cellbio.20.022003.114106. PMID 15473833.
- ^ Fullick, P. (1994), Physics, Heinemann, pp. 141–142, ISBN 0-435-57078-1
- ^ Jump up to: a b Atkins, Peter; De Paula, Julio (2006). Atkins' Physical Chemistry (8th ed.). W. H. Freeman. pp. 200–202. ISBN 978-0-7167-8759-4.
- ^ Atkins, Peter W.; Jones, Loretta (2008). Chemical Principles: The Quest for Insight (2nd ed.). ISBN 978-0-7167-9903-0.
- ^ IUPAC, Compendium of Chemical Terminology, 2nd ed. (the "Gold Book") (1997). Online corrected version: (2006–) "chemical equilibrium". doi:10.1351/goldbook.C01023
- ^ IUPAC, Compendium of Chemical Terminology, 2nd ed. (the "Gold Book") (1997). Online corrected version: (2006–) "chemical reaction". doi:10.1351/goldbook.C01033
- ^ "What is Chemistry?". Chemweb.ucc.ie. Retrieved 12 June 2011.
- ^ "Definition of CHEMISTRY". www.merriam-webster.com. Retrieved 24 August 2020.
- ^ "Definition of chemistry | Dictionary.com". www.dictionary.com. Retrieved 24 August 2020.
- ^ "Chemistry Is Everywhere". American Chemical Society.
- ^ Clausius, R. (1850). "Ueber die bewegende Kraft der Wärme und die Gesetze, welche sich daraus für die Wärmelehre selbst ableiten lassen" [On the motive power of heat and the laws which can be deduced therefrom regarding the theory of heat]. Annalen der Physik (in German). 155 (4): 500–524. Bibcode:1850AnP...155..500C. doi:10.1002/andp.18501550403. hdl:2027/uc1.$b242250.
- ^ Clapeyron, M. C. (1834). "Mémoire sur la puissance motrice de la chaleur". Journal de l'École Polytechnique (in French). 23: 153–190. ark:/12148/bpt6k4336791/f157.
- ^ Clausius theorem at Wolfram Research
- ^ Finn, Colin B. P. Thermal Physics. 2nd ed., CRC Press, 1993.
- ^ Giancoli, Douglas C. Physics: Principles with Applications. 6th ed., Pearson/Prentice Hall, 2005.
- ^ Mortimer, R. G. Physical Chemistry. 3rd ed., p. 120, Academic Press, 2008.
- ^ "Archived copy" (PDF). Archived from the original (PDF) on 2013-01-24. Retrieved 2013-10-16.CS1 maint: archived copy as title (link)
- ^ "COP (Coefficient of performance)".
- ^ "Archived copy" (PDF). Archived from the original (PDF) on 2009-01-07. Retrieved 2013-10-16.CS1 maint: archived copy as title (link)
- ^ colloquial meaning of burning is combustion accompanied by flames
- ^ Narayan, K. Lalit (2008). Computer Aided Design and Manufacturing. New Delhi: Prentice Hall of India. p. 3. ISBN 978-8120333420.
- ^ Narayan, K. Lalit (2008). Computer Aided Design and Manufacturing. New Delhi: Prentice Hall of India. p. 4. ISBN 978-8120333420.
- ^ Duggal, Vijay (2000). Cadd Primer: A General Guide to Computer Aided Design and Drafting-Cadd, CAD. Mailmax Pub. ISBN 978-0962916595.
- ^ Jump up to: a b U.S. Congress, Office of Technology Assessment (1984). Computerized manufacturing automation. DIANE Publishing. p. 48. ISBN 978-1-4289-2364-5.
- ^ Hosking, Dian Marie; Anderson, Neil (1992), Organizational change and innovation, Taylor & Francis, p. 240, ISBN 978-0-415-06314-2
- ^ Daintith, John (2004). A dictionary of computing (5 ed.). Oxford University Press. p. 102. ISBN 978-0-19-860877-6.
- ^ Kreith, Frank (1998). The CRC handbook of mechanical engineering. CRC Press. p. 15-1. ISBN 978-0-8493-9418-8.
- ^ Matthews, Clifford (2005). Aeronautical engineer's data book (2nd ed.). Butterworth-Heinemann. p. 229. ISBN 978-0-7506-5125-7.
- ^ Pichler, Franz; Moreno-Díaz, Roberto (1992). Computer aided systems theory. Springer. p. 602. ISBN 978-3-540-55354-0.
- ^ Boothroyd, Geoffrey; Knight, Winston Anthony (2006). Fundamentals of machining and machine tools (3rd ed.). CRC Press. p. 401. ISBN 978-1-57444-659-3.
- ^ IEEE Computer Society; ACM (December 12, 2004). Computer Engineering 2004: Curriculum Guidelines for Undergraduate Degree Programs in Computer Engineering (PDF). p. iii. Retrieved December 17, 2012.
Computer System engineering has traditionally been viewed as a combination of both electronic engineering (EE) and computer science (CS).
- ^ "WordNet Search—3.1". Wordnetweb.princeton.edu. Retrieved 14 May 2012.
- ^ Cox D.R., Hinkley D.V. (1974) Theoretical Statistics, Chapman & Hall, p49, p209
- ^ Kendall, M.G. and Stuart, D.G. (1973) The Advanced Theory of Statistics. Vol 2: Inference and Relationship, Griffin, London. Section 20.4
- ^ Neyman, J. (1937). "Outline of a Theory of Statistical Estimation Based on the Classical Theory of Probability". Philosophical Transactions of the Royal Society A. 236 (767): 333–380. Bibcode:1937RSPTA.236..333N. doi:10.1098/rsta.1937.0005. JSTOR 91337.
- ^ Jump up to: a b Zumdahl, Stephen S., & Zumdahl, Susan A. Chemistry. Houghton Mifflin, 2007, ISBN 0618713700
- ^ Richard Feynman (1970). The Feynman Lectures on Physics Vol I. Addison Wesley. ISBN 978-0-201-02115-8.
- ^ Jump up to: a b "Systems & Control Engineering FAQ | Electrical Engineering and Computer Science". engineering.case.edu. Case Western Reserve University. 20 November 2015. Retrieved 27 June 2017.
- ^ Sharma (2008). Atomic And Nuclear Physics. Pearson Education India. p. 478. ISBN 978-81-317-1924-4.
- ^ Draft Resolution A "On the revision of the International System of units (SI)" to be submitted to the CGPM at its 26th meeting in November 2018. (PDF)
- ^ "How is electrostatic force explained?". Reference*. IAC Publishing, LLC. 2019. Retrieved January 5, 2019.
- ^ "Ernest Lawrence's Cyclotron". www2.lbl.gov. Retrieved 2018-04-06.
- ^ "Ernest Lawrence - Biographical". nobelprize.org. Retrieved 2018-04-06.
- ^ U.S. Patent 1,948,384 Lawrence, Ernest O. Method and apparatus for the acceleration of ions, filed: January 26, 1932, granted: February 20, 1934
- ^ Lawrence, Earnest O.; Livingston, M. Stanley (April 1, 1932). "The Production of High Speed Light Ions Without the Use of High Voltages". Physical Review. American Physical Society. 40 (1): 19–35. Bibcode:1932PhRv...40...19L. doi:10.1103/PhysRev.40.19.
- ^ Jump up to: a b Close, F. E.; Close, Frank; Marten, Michael; et al. (2004). The Particle Odyssey: A Journey to the Heart of Matter. Oxford University Press. pp. 84–87. ISBN 978-0-19-860943-8.
- ^ "Ernest Lawrence - Facts". nobelprize.org. Retrieved 2018-04-06.
- ^ Silberberg, Martin S. (2009). Chemistry: the molecular nature of matter and change (5th ed.). Boston: McGraw-Hill. p. 206. ISBN 9780073048598.
- ^ Wiktionary
- ^ Davidge, R.W. (1979) Mechanical Behavior of Ceramics, Cambridge Solid State Science Series, Eds. Clarke, D.R., et al.
- ^ Zarzycki, J. (1991) Glasses and the Vitreous State, Cambridge Solid State Science Series, Eds. Clarke, D.R., et al.
- ^ Truesdell, C.; Noll, W. (2004). The non-linear field theories of mechanics (3rd ed.). Springer. p. 48.
- ^ Wu, H.-C. (2005). Continuum Mechanics and Plasticity. CRC Press. ISBN 978-1-58488-363-0.
- ^ The National Aeronautic and Atmospheric Administration's Glenn Research Center. "Gas Density Glenn research Center". grc.nasa.gov. Archived from the original on April 14, 2013. Retrieved March 31, 2019.
- ^ "Density definition in Oil Gas Glossary". Oilgasglossary.com. Archived from the original on August 5, 2010. Retrieved September 14, 2010.
- ^ Macauley, David; Ardley, Neil (1998). The New Way Things Work. Boston, USA: Houghton Mifflin Company. p. 56. ISBN 978-0-395-93847-8.
- ^ Goldberg, David (2006). Fundamentals of Chemistry (5th ed.). McGraw-Hill. ISBN 978-0-07-322104-5.
- ^ Ogden, James (1999). The Handbook of Chemical Engineering. Research & Education Association. ISBN 978-0-87891-982-6.
- ^ "Dimensional Analysis or the Factor Label Method". Mr Kent's Chemistry Page.
- ^ Born, Max; Wolf, Emil (October 1999). Principles of Optics. Cambridge: Cambridge University Press. pp. 14–24. ISBN 978-0-521-64222-4.
- ^ Tom Henderson. "Describing Motion with Words". The Physics Classroom. Retrieved 2 January 2012.
- ^ Giordano, Nicholas (2009). College Physics: Reasoning and Relationships. Cengage Learning. pp. 421–424. ISBN 978-0534424718.
- ^ Crump, K. S.; Hoel, D. G.; Langley, C. H.; Peto, R. (1 September 1976). "Fundamental Carcinogenic Processes and Their Implications for Low Dose Risk Assessment". Cancer Research. 36 (9 Part 1): 2973–2979. PMID 975067.
- ^ "Definition of DRAG". www.merriam-webster.com.
- ^ French (1970), p. 211, Eq. 7-20
- ^ "What is Drag?". Archived from the original on 2010-05-24. Retrieved 2019-02-23.
- ^ G. Falkovich (2011). Fluid Mechanics (A short course for physicists). Cambridge University Press. ISBN 978-1-107-00575-4.
- ^ K.J. Laidler and J.H. Meiser, Physical Chemistry, Benjamin/Cummings 1982, p.18. ISBN 0-8053-5682-7
- ^ Horowitz, Paul; Hill, Winfield (2015). The art of electronics (3rd ed.). Cambridge University Press. ISBN 978-0-521-80926-9.
- ^ Anthony C. Fischer-Cripps (2004). The electronics companion. CRC Press. p. 13. ISBN 978-0-7503-1012-3.
- ^ Lakatos, John; Oenoki, Keiji; Judez, Hector; Oenoki, Kazushi; Hyun Kyu Cho (March 1998). "Learn Physics Today!". Lima, Peru: Colegio Dr. Franklin D. Roosevelt. Archived from the original on 2009-02-27. Retrieved 2009-03-10.
- ^ Purcell, Edward M.; Morin, David J. (2013). Electricity and Magnetism (3rd ed.). New York: Cambridge University Press. pp. 14–20. ISBN 978-1-107-01402-2.
- ^ Browne, p 225: "... around every charge there is an aura that fills all space. This aura is the electric field due to the charge. The electric field is a vector field... and has a magnitude and direction."
- ^ Wiktionary
- ^ Richard Feynman (1970). The Feynman Lectures on Physics Vol II. Addison Wesley Longman. ISBN 978-0-201-02115-8.
A "field" is any physical quantity which takes on different values at different points in space.
- ^ *Purcell and Morin, Harvard University. (2013). Electricity and Magnetism, 820p (3rd ed.). Cambridge University Press, New York. ISBN 978-1-107-01402-2. p 430: "These waves... require no medium to support their propagation. Traveling electromagnetic waves carry energy, and... the Poynting vector describes the energy flow...;" p 440: ... the electromagnetic wave must have the following properties: 1) The field pattern travels with speed c (speed of light); 2) At every point within the wave... the electric field strength E equals "c" times the magnetic field strength B; 3) The electric field and the magnetic field are perpendicular to one another and to the direction of travel, or propagation."
- ^ * Browne, Michael (2013). Physics for Engineering and Science, p427 (2nd ed.). McGraw Hill/Schaum, New York. ISBN 978-0-07-161399-6.; p319: "For historical reasons, different portions of the EM spectrum are given different names, although they are all the same kind of thing. Visible light constitutes a narrow range of the spectrum, from wavelengths of about 400-800 nm.... ;p 320 "An electromagnetic wave carries forward momentum... If the radiation is absorbed by a surface, the momentum drops to zero and a force is exerted on the surface... Thus the radiation pressure of an electromagnetic wave is (formula)."
- ^ Course in Electro-mechanics, for Students in Electrical Engineering, 1st Term of 3d Year, Columbia University, Adapted from Prof. F.E. Nipher's "Electricity and Magnetism". By . 1901.
- ^ Szolc T.; ; Michajłow M.; Pregowska A. (2014). "An investigation of the dynamic electromechanical coupling effects in machine drive systems driven by asynchronous motors". Mechanical Systems and Signal Processing. Mechanical Systems and Signal Processing. 49 (1–2): 118–134. Bibcode:2014MSSP...49..118S. doi:10.1016/j.ymssp.2014.04.004.
- ^ The Elements of Electricity, "Part V. Electro-Mechanics." By . John Wiley & sons, Incorporated, 1922.
- ^ ; Szolc T.; Pochanke A.; Pregowska A. (2016). "An influence of the stepping motor control and friction models on precise positioning of the complex mechanical system". Mechanical Systems and Signal Processing. Mechanical Systems and Signal Processing, Vol.70-71, pp.397-413. 70–71: 397–413. Bibcode:2016MSSP...70..397K. doi:10.1016/j.ymssp.2015.09.030. ISSN 0888-3270.
- ^ Coff, Jerry (10 September 2010). "What Is An Electron". Retrieved 10 September 2010.
- ^ Jump up to: a b Curtis, L.J. (2003). Atomic Structure and Lifetimes: A Conceptual Approach. Cambridge University Press. p. 74. ISBN 978-0-521-53635-6.
- ^ Eichten, Estia J.; Lane, Kenneth D.; Peskin, Michael E. (1983-03-14). "New Tests for Quark and Lepton Substructure". Physical Review Letters. American Physical Society (APS). 50 (11): 811–814. Bibcode:1983PhRvL..50..811E. doi:10.1103/physrevlett.50.811. ISSN 0031-9007. OSTI 1446807.
- ^ "CODATA value: proton-electron mass ratio". 2006 CODATA recommended values. National Institute of Standards and Technology. Retrieved 18 July 2009.
- ^ "CODATA Value: Planck constant in eV s".https://physics.nist.gov/cgi-bin/cuu/Value?hev Archived https://web.archive.org/web/20150122120538/http://physics.nist.gov/cgi-bin/cuu/Value?hev from the original on 22 January 2015. Retrieved 30 March 2015.
- ^ Jean Maruani (1989). Molecules in Physics, Chemistry and Biology: v. 3: Electronic Structure and Chemical Reactivity. Springer. p. 73. ISBN 978-90-277-2598-1. Retrieved 14 March 2013.
- ^ IUPAC, Compendium of Chemical Terminology, 2nd ed. (the "Gold Book") (1997). Online corrected version: (2006–) "Electronegativity". doi:10.1351/goldbook.E01990
- ^ "electronics | Devices, Facts, & History". Encyclopædia Britannica. Retrieved 2018-09-19.
- ^ Oxtoby, D. W; Gillis, H.P., Butler, L. J. (2015).Principles of Modern Chemistry, Brooks Cole. p. 617. ISBN 978-1305079113
- ^ "Motor". Dictionary.reference.com. Retrieved 2011-05-09.
a person or thing that imparts motion, esp. a contrivance, as a steam engine, that receives and modifies energy from some source in order to utilize it in driving machinery.
- ^ Dictionary.com: (World heritage) "3. any device that converts another form of energy into mechanical energy so as to produce motion"
- ^ "definition of "engineering"". Cambridge Academic Content Dictionary. Cambridge University.
- ^ "About IAENG". iaeng.org. International Association of Engineers. Retrieved December 17, 2016.
- ^ Jump up to: a b c d e f Dharmaraj, E.. Engineering Economics. Mumbai, IN: Himalaya Publishing House, 2009. ProQuest ebrary. Web. 9 November 2016.
- ^ Morris, W. Thomas. (1960). Engineering economy: the analysis of management decisions. Homewood, Ill.: R. D. Irwin.
- ^ "Careers in Environmental Engineering and Environmental Science". American Academy of Environmental Engineers & Scientists. Retrieved 2019-03-23.
- ^ "Bureau of Labor Statistics, U.S. Department of Labor.U.S. Department of Labor, Occupational Outlook Handbook, 2010-11 Edition"
- ^ "Major: Engineering Physics". The Princeton Review. 2017. p. 01. Retrieved June 4, 2017.
- ^ "Introduction" (online). Princeton University. Retrieved June 26, 2011.
- ^ Khare, P.; A. Swarup (2009-01-26). Engineering Physics: Fundamentals & Modern Applications (13th ed.). Jones & Bartlett Learning. pp. xiii–Preface. ISBN 978-0-7637-7374-8.
- ^ Physics (online). Retrieved June 26, 2011.
- ^ Stryer L, Berg JM, Tymoczko JL (2002). Biochemistry (5th ed.). San Francisco: W.H. Freeman. ISBN 0-7167-4955-6.
- ^ Mosteller, F.; Tukey, J. W. (1987) [1968]. "Data Analysis, including Statistics". The Collected Works of John W. Tukey: Philosophy and Principles of Data Analysis 1965–1986. 4. CRC Press. pp. 601–720 [p. 633]. ISBN 0-534-05101-4 – via Google Books.
- ^ Timoshenko, S., (1953), History of strength of materials, McGraw-Hill New York
- ^ Truesdell, C., (1960), The rational mechanics of flexible or elastic bodies 1638–1788, Venditioni Exponunt Orell Fussli Turici.
- ^ "Gate for the Greek language" on-line dictionary Archived 2017-12-05 at the Wayback Machine. greek-language.gr
- ^ The International System of Units (SI) (8th ed.). Bureau International des Poids et Mesures (International Committee for Weights and Measures). 2006. p. 144.
- ^ The term "magnitude" is used in the sense of "absolute value": The charge of an electron is negative, but F is always defined to be positive.
- ^ "2018 CODATA Value: Faraday constant". The NIST Reference on Constants, Units, and Uncertainty. NIST. 20 May 2019. Retrieved 2019-05-20.
- ^ "2018 CODATA Value: elementary charge". The NIST Reference on Constants, Units, and Uncertainty. NIST. 20 May 2019. Retrieved 2019-05-20.
- ^ "2018 CODATA Value: Avogadro constant". The NIST Reference on Constants, Units, and Uncertainty. NIST. 20 May 2019. Retrieved 2019-05-20.
- ^ Arthur Schuster, An Introduction to the Theory of Optics, London: Edward Arnold, 1904 online.
- ^ Ghatak, Ajoy (2009), Optics (4th ed.), ISBN 978-0-07-338048-3
- ^ Daryl L. Logan (2011). A first course in the finite element method. Cengage Learning. ISBN 978-0495668251.
- ^ Duderstadt, James J.; Martin, William R. (1979). "Chapter 4:The derivation of continuum description from transport equations". In Wiley-Interscience Publications (ed.). Transport theory. New York. p. 218. ISBN 978-0471044925.
- ^ Freidberg, Jeffrey P. (2008). "Chapter 10:A self-consistent two-fluid model". In Cambridge University Press (ed.). Plasma Physics and Fusion Energy (1 ed.). Cambridge. p. 225. ISBN 978-0521733175.
- ^ White, Frank M. (2011). Fluid Mechanics (7th ed.). McGraw-Hill. ISBN 978-0-07-352934-9.
- ^ "Hydrostatics". Merriam-Webster. Retrieved 11 September 2018.
- ^ "Standard Microscopy Terminology". University of Minnesota Characterization Facility website. Archived from the original on 2008-03-02. Retrieved 2006-04-21.
- ^ IEEE Std 260.1-2004, IEEE Standard Letter Symbols for Units of Measurement (SI Units, Customary Inch-Pound Units, and Certain Other Units)
- ^ Fletcher, Leroy S.; Shoup, Terry E. (1978), Introduction to Engineering, Prentice-Hall, ISBN 978-0135018583, LCCN 77024142.: 257
- ^ Budynas, Richard G.; Nisbett, J. Keith (2014-01-27). Mechanical Engineering Design. McGraw Hill Education. ISBN 978-0073529288.
- ^ Suresh, S. (2004). Fatigue of Materials. Cambridge University Press. ISBN 978-0-521-57046-6.
- ^ Ramsay, J. A. (1 May 1949). "A New Method of Freezing-Point Determination for Small Quantities". Journal of Experimental Biology. 26 (1): 57–64. doi:10.1242/jeb.26.1.57. PMID 15406812.
- ^ "friction". Merriam-Webster Dictionary.
- ^ Beer, Ferdinand P.; Johnston, E. Russel, Jr. (1996). Vector Mechanics for Engineers (Sixth ed.). McGraw-Hill. p. 397. ISBN 978-0-07-297688-5.
- ^ Jump up to: a b Meriam, J. L.; Kraige, L. G. (2002). Engineering Mechanics (fifth ed.). John Wiley & Sons. p. 328. ISBN 978-0-471-60293-4.
- ^ Ruina, Andy; Pratap, Rudra (2002). Introduction to Statics and Dynamics (PDF). Oxford University Press. p. 713.
- ^ Hibbeler, R. C. (2007). Engineering Mechanics (Eleventh ed.). Pearson, Prentice Hall. p. 393. ISBN 978-0-13-127146-3.
- ^ Soutas-Little, Robert W.; Inman, Balint (2008). Engineering Mechanics. Thomson. p. 329. ISBN 978-0-495-29610-2.
- ^ "sidfn". Phon.UCL.ac.uk. Archived from the original on 2013-01-06. Retrieved 2012-11-27.
- ^ Lemmetty, Sami (1999). "Phonetics and Theory of Speech Production". Acoustics.hut.fi. Retrieved 2012-11-27.
- ^ "Fundamental Frequency of Continuous Signals" (PDF). Fourier.eng.hmc.edu. 2011. Retrieved 2012-11-27.
- ^ "Standing Wave in a Tube II – Finding the Fundamental Frequency" (PDF). Nchsdduncanapphysics.wikispaces.com. Archived from the original (PDF) on 2014-03-13. Retrieved 2012-11-27.
- ^ "Physics: Standing Waves". Physics.Kennesaw.edu. Archived from the original (PDF) on 2019-12-15. Retrieved 2012-11-27.
- ^ Pollock, Steven (2005). "Phys 1240: Sound and Music" (PDF). Colorado.edu. Archived from the original (PDF) on 2014-05-15. Retrieved 2012-11-27.
- ^ "Standing Waves on a String". Hyperphysics.phy-astr.gsu.edu. Retrieved 2012-11-27.
- ^ "Creating musical sounds". OpenLearn. Open University. Retrieved 2014-06-04.
- ^ Fackler, Orrin; Tran, J. Thanh Van (1988). 5th Force Neutrino Physics. Atlantica Séguier Frontières. ISBN 978-2863320549.
- ^ Weisstein, Eric W. (2007). "Fifth Force". World of Science. Wolfram Research. Retrieved September 14, 2017.
- ^ Franklin, Allan; Fischbach, Ephraim (2016). The Rise and Fall of the Fifth Force: Discovery, Pursuit, and Justification in Modern Physics, 2nd Ed. Springer. ISBN 978-3319284125.
- ^ "Professional Engineers Examination".
- ^ "battery" (def. 4b), Merriam-Webster Online Dictionary (2008). Retrieved 6 August 2008.
- ^ Vincenzo De Risi (31 January 2015). Mathematizing Space: The Objects of Geometry from Antiquity to the Early Modern Age. Birkhäuser. pp. 1–. ISBN 978-3-319-12102-4.
- ^ Jump up to: a b Sheriff 1991
- ^ IUGG 2011
- ^ AGU 2011
- ^ Gutenberg, B., 1929, Lehrbuch der Geophysik. Leipzig. Berlin (Gebruder Borntraeger).
- ^ Runcorn, S.K, (editor-in-chief), 1967, International dictionary of geophysics:. Pergamon, Oxford, 2 volumes, 1,728 pp., 730 fig
- ^ C.R. Nave. "The Color Force". HyperPhysics. Georgia State University, Department of Physics. Retrieved 2012-04-02.
- ^ Jump up to: a b Keith J. Laidler and John M. Meiser, Physical Chemistry (Benjamin/Cummings 1982), pp. 18–19
- ^ Jump up to: a b "Gravitational Potential Energy". hyperphysics.phy-astr.gsu.edu. Retrieved 10 January 2017.
- ^ Feynman, Richard (1970). The Feynman Lectures on Physics. I. Addison Wesley Longman. ISBN 978-0-201-02115-8.
- ^ Geroch, Robert (1981). General Relativity from A to B. University of Chicago Press. p. 181. ISBN 978-0-226-28864-2.
- ^ Grøn, Øyvind; Hervik, Sigbjørn (2007). Einstein's General Theory of Relativity: with Modern Applications in Cosmology. Springer Japan. p. 256. ISBN 978-0-387-69199-2.
- ^ Foster, J.; Nightingale, J. D. (2006). A Short Course in General Relativity (3 ed.). Springer Science & Business. p. 55. ISBN 978-0-387-26078-5.
- ^ Solivérez, C.E. (2016). Electrostatics and magnetostatics of polarized ellipsoidal bodies: the depolarization tensor method (1st English ed.). Free Scientific Information. ISBN 978-987-28304-0-3.
- ^ http://www.academie-sciences.fr/pdf/dossiers/Poincare/Poincare_pdf/Poincare_CR1905.pdf
- ^ Einstein, A (June 1916). "Näherungsweise Integration der Feldgleichungen der Gravitation". Sitzungsberichte der Königlich Preussischen Akademie der Wissenschaften Berlin. part 1: 688–696. Bibcode:1916SPAW.......688E. Archived from the original on 2016-01-15. Retrieved 2014-11-15.
- ^ Einstein, A (1918). "Über Gravitationswellen". Sitzungsberichte der Königlich Preussischen Akademie der Wissenschaften Berlin. part 1: 154–167. Bibcode:1918SPAW.......154E. Archived from the original on 2016-01-15. Retrieved 2014-11-15.
- ^ Finley, Dave. "Einstein's gravity theory passes toughest test yet: Bizarre binary star system pushes study of relativity to new limits". Phys.Org.
- ^ The Detection of Gravitational Waves using LIGO, B. Barish Archived 2016-03-03 at the Wayback Machine
- ^ Einstein, Albert; Rosen, Nathan (January 1937). "On gravitational waves". Journal of the Franklin Institute. 223 (1): 43–54. Bibcode:1937FrInJ.223...43E. doi:10.1016/S0016-0032(37)90583-0.
- ^ Comins, Neil F.; Kaufmann, William J. (2008). Discovering the Universe: From the Stars to the Planets. MacMillan. p. 347. Bibcode:2009dufs.book.....C. ISBN 978-1429230421.
- ^ Reif (1965): "[in the special case of purely thermal interaction between two system:] The mean energy transferred from one system to the other as a result of purely thermal interaction is called 'heat'" (p. 67). the quantity Q [...] is simply a measure of the mean energy change not due to the change of external parameters. [...] splits the total mean energy change into a part W due to mechanical interaction and a part Q due to thermal interaction [...] by virtue of [the definition ΔU = Q − W, present notation, physics sign convention], both heat and work have the dimensions of energy" (p. 73). C.f.: "heat is thermal energy in transfer" Stephen J. Blundell, Katherine M. Blundell, Concepts in Thermal Physics (2009), p. 13 Archived 24 June 2018 at the Wayback Machine.
- ^ Thermodynamics and an Introduction to Thermostatics, 2nd Edition, by Herbert B. Callen, 1985, http://cvika.grimoar.cz/callen/ Archived 17 October 2018 at the Wayback Machine or http://keszei.chem.elte.hu/1alapFizkem/H.B.Callen-Thermodynamics.pdf Archived 30 December 2016 at the Wayback Machine , p. 8: Energy may be transferred via ... work. "But it is equally possible to transfer energy via the hidden atomic modes of motion as well as via those that happen to be macroscopically observable. An energy transfer via the hidden atomic modes is called heat."
- ^ Born, M. (1949), p. 31.
- ^ Pippard, A.B. (1957/1966), p. 16.
- ^ Landau, L., Lifshitz, E.M. (1958/1969), p. 43
- ^ Callen, H.B. (1960/1985), pp. 18–19.
- ^ Bailyn, M. (1994), p. 82.
- ^ "Huygens' Principle". MathPages. Retrieved 2017-10-03.
- ^ Wiktionary
- ^ Clapeyron, E. (1834). "Mémoire sur la puissance motrice de la chaleur". (in French). XIV: 153–90. Facsimile at the Bibliothèque nationale de France (pp. 153–90).
- ^ Krönig, A. (1856). "Grundzüge einer Theorie der Gase". Annalen der Physik und Chemie (in German). 99 (10): 315–22. Bibcode:1856AnP...175..315K. doi:10.1002/andp.18561751008. Facsimile at the Bibliothèque nationale de France (pp. 315–22).
- ^ Clausius, R. (1857). "Ueber die Art der Bewegung, welche wir Wärme nennen". Annalen der Physik und Chemie (in German). 176 (3): 353–79. Bibcode:1857AnP...176..353C. doi:10.1002/andp.18571760302. Facsimile at the Bibliothèque nationale de France (pp. 353–79).
- ^ "The Definitive Glossary of Higher Mathematical Jargon — Identity". Math Vault. 2019-08-01. Retrieved 2019-12-01.
- ^ Jump up to: a b "Mathwords: Identity". www.mathwords.com. Retrieved 2019-12-01.
- ^ "Identity - math word definition - Math Open Reference". www.mathopenref.com. Retrieved 2019-12-01.
- ^ Cole, Matthew (2005). Explore science, 2nd Ed. Pearson Education. p. 178. ISBN 978-981-06-2002-8.
- ^ Merriam-Webster's collegiate dictionary, 11th Ed. Merriam-Webster. 2003. p. 629. ISBN 978-0-87779-809-5.
inclined plane definition dictionary.
- ^ Jump up to: a b "The Inclined Plane". Math and science activity center. Edinformatics. 1999. Retrieved March 11, 2012.
- ^ https://en.wiktionary.org/wiki/indefinite_integral Wiktionary
- ^ Serway, A. Raymond; Jewett, John W.; Wilson, Jane; Wilson, Anna; Rowlands, Wayne (1 October 2016). "32". Physics for global scientists and engineers (2ndition ed.). p. 901. ISBN 9780170355520.
- ^ Alexander, Charles; Sadiku, Matthew. Fundamentals of Electric Circuits (3 ed.). McGraw-Hill. p. 211.
- ^ Salvendy, Gabriel. Handbook of Industrial Engineering. John Wiley & Sons, Inc; 3rd edition p. 5
- ^ "What IEs Do". www.iienet2.org. Retrieved September 24, 2015.
- ^ "Careers in Chemistry: Inorganic Chemistry". American Chemical Society. Archived from the original on 2012-10-29.
- ^ "Ionic bond". IUPAC Compendium of Chemical Terminology. 2009. doi:10.1351/goldbook.IT07058. ISBN 978-0-9678550-9-7.
- ^ Herzog, Gregory F. (2 June 2020). "Isotope". Encyclopedia Britannica.
- ^ Kapusta, J.; Müller, B.; Rafelski, J. (9 December 2003). [no title cited]. ISBN 9780444511102. Retrieved 25 September 2014 – via Google Books.[full citation needed][dead link]
- ^ "Shared Physics prize for elementary particle" (Press release). The Royal Swedish Academy of Sciences. 18 October 1976. Retrieved 23 April 2012.
- ^ International Bureau of Weights and Measures (2006), The International System of Units (SI) (PDF) (8th ed.), p. 120, ISBN 92-822-2213-6, archived from the original (PDF) on 2017-08-14
- ^ American Heritage Dictionary of the English Language, Online Edition (2009). Houghton Mifflin Co., hosted by Yahoo! Education.
- ^ The American Heritage Dictionary, Second College Edition (1985). Boston: Houghton Mifflin Co., p. 691.
- ^ McGraw-Hill Dictionary of Physics, Fifth Edition (1997). McGraw-Hill, Inc., p. 224.
- ^ Rao, Y. V. C. (1997). Chemical Engineering Thermodynamics. Universities Press. p. 158. ISBN 978-81-7371-048-3.
- ^ Young, Hugh D.; Freedman, Roger A. (2008). University Physics. 1 (12 ed.). Pearson Education. ISBN 978-0-321-50125-7.
- ^ Edmund Taylor Whittaker (1904). A Treatise on the Analytical Dynamics of Particles and Rigid Bodies. Cambridge University Press. Chapter 1. ISBN 0-521-35883-3.
- ^ Joseph Stiles Beggs (1983). Kinematics. Taylor & Francis. p. 1. ISBN 0-89116-355-7.
- ^ Thomas Wallace Wright (1896). Elements of Mechanics Including Kinematics, Kinetics and Statics. E and FN Spon. Chapter 1.
- ^ Streeter, V.L. (1951-1966) Fluid Mechanics, Section 3.3 (4th edition). McGraw-Hill
- ^ Geankoplis, Christie John (2003). Transport Processes and Separation Process Principles. Prentice Hall Professional Technical Reference. ISBN 978-0-13-101367-4. Archived from the original on 2015-05-01.
- ^ Noakes, Cath; Sleigh, Andrew (January 2009). "Real Fluids". An Introduction to Fluid Mechanics. University of Leeds. Archived from the original on 21 October 2010. Retrieved 23 November 2010.
- ^ "Laplace Transform: A First Introduction". Math Vault. Retrieved 2020-08-08.
- ^ "Differential Equations - Laplace Transforms". tutorial.math.lamar.edu. Retrieved 2020-08-08.
- ^ Weisstein, Eric W. "Laplace Transform". mathworld.wolfram.com. Retrieved 2020-08-08.
- ^ Jump up to: a b Gall, John (2002). The Systems Bible (3rd ed.). General Systemantics Press.
The System always kicks back
- ^ Lenz, E. (1834), "Ueber die Bestimmung der Richtung der durch elektodynamische Vertheilung erregten galvanischen Ströme", Annalen der Physik und Chemie, 107 (31), pp. 483–494. A partial translation of the paper is available in Magie, W. M. (1963), A Source Book in Physics, Harvard: Cambridge MA, pp. 511–513.
- ^ Schmitt, Ron. Electromagnetics explained. 2002. Retrieved 16 July 2010.
- ^ "Lepton (physics)". Encyclopædia Britannica. Retrieved 2010-09-29.
- ^ CIE (1987). International Lighting Vocabulary Archived 27 February 2010 at the Wayback Machine. Number 17.4. CIE, 4th edition. ISBN 978-3-900734-07-7.
By the International Lighting Vocabulary, the definition of light is: "Any radiation capable of causing a visual sensation directly." - ^ Pal, G.K.; Pal, Pravati (2001). "chapter 52". Textbook of Practical Physiology (1st ed.). Chennai: Orient Blackswan. p. 387. ISBN 978-81-250-2021-9. Retrieved 11 October 2013.
The human eye has the ability to respond to all the wavelengths of light from 400–700 nm. This is called the visible part of the spectrum.
- ^ Buser, Pierre A.; Imbert, Michel (1992). Vision. MIT Press. p. 50. ISBN 978-0-262-02336-8. Retrieved 11 October 2013.
Light is a special class of radiant energy embracing wavelengths between 400 and 700 nm (or mμ), or 4000 to 7000 Å.
- ^ "The Ultimate Guide to Logarithm — Theory & Applications", Math Vault, 8 May 2016, retrieved 24 July 2019
- ^ All statements in this section can be found in Shirali 2002, Section 4 , Downing 2003, p. 275 , or Kate & Bhapkar 2009, p. 1-1 , for example.
- ^ Incropera; DeWitt; Bergman; Lavine (2007). Fundamentals of Heat and Mass Transfer (6th ed.). John Wiley & Sons. pp. 260–261. ISBN 978-0-471-45728-2.
- ^ Close, Frank (2010). Neutrinos (softcover ed.). Oxford University Press. ISBN 978-0-199-69599-7.
- ^ Jump up to: a b Jayawardhana, Ray (2015). The Neutrino Hunters: The chase for the ghost particle and the secrets of the universe (softcover ed.). Oneworld Publications. ISBN 978-1-780-74647-0.
- ^ Mertens, Susanne (2016). "Direct neutrino mass experiments". Journal of Physics: Conference Series. 718 (2): 022013. arXiv:1605.01579. Bibcode:2016JPhCS.718b2013M. doi:10.1088/1742-6596/718/2/022013. S2CID 56355240.
- ^ Overbye, Dennis (15 April 2020). "Why The Big Bang Produced Something Rather Than Nothing - How did matter gain the edge over antimatter in the early universe? Maybe, just maybe, neutrinos". The New York Times. Retrieved 16 April 2020.
- ^ Close, Frank (2010). Neutrinos (softcover ed.). Oxford University Press. ISBN 978-0-199-69599-7.
- ^ Panton, Ronald L. (2013). Incompressible Flow (Fourth ed.). Hoboken: John Wiley & Sons. p. 114. ISBN 978-1-118-01343-4.
- ^ Batchelor, G. K. (2000) [1967]. An Introduction to Fluid Dynamics. Cambridge Mathematical Library series, Cambridge University Press. ISBN 978-0-521-66396-0.
- ^ Kundu, P.; Cohen, I. Fluid Mechanics. p. (page needed).
- ^ Kirby, B. J. (2010). Micro- and Nanoscale Fluid Mechanics: Transport in Microfluidic Devices. Cambridge University Press. ISBN 978-0-521-11903-0.
- ^ Vijaya, A.V.; Rodriguez, Dora, Figuring Out Mathematics, Pearson Education India, pp. 20–21, ISBN 9788131703571.
- ^ Miessler, G. L. and Tarr, D. A. (2010) Inorganic Chemistry 3rd ed., Pearson/Prentice Hall publisher, ISBN 0-13-035471-6.
- ^ britannica.com
- ^ Livingston, M. S.; Blewett, J. (1969). Particle Accelerators. New York: McGraw-Hill. ISBN 978-1-114-44384-6.
- ^ Gardner, Julian W.; Varadan, Vijay K.; Awadelkarim, Osama O. (2001). Microsensors, MEMS, and Smart Devices John 2. pp. 23–322. ISBN 978-0-471-86109-6.
- ^ Arthur Schuster (1904). An Introduction to the Theory of Optics. London: Edward Arnold.
An Introduction to the Theory of Optics By Arthur Schuster.
- ^ "The Higgs Boson". CERN.
- ^ "The BEH-Mechanism, Interactions with Short Range Forces and Scalar Particles" (PDF). 8 October 2013.
- ^ "Pascal's principle - Definition, Example, & Facts". britannica.com. Archived from the original on 2 June 2015. Retrieved 9 May 2018.
- ^ "Pascal's Principle and Hydraulics". www.grc.nasa.gov. Archived from the original on 5 April 2018. Retrieved 9 May 2018.
- ^ "Pressure". hyperphysics.phy-astr.gsu.edu. Archived from the original on 28 October 2017. Retrieved 9 May 2018.
- ^ Bloomfield, Louis (2006). How Things Work: The Physics of Everyday Life (Third ed.). John Wiley & Sons. p. 153. ISBN 978-0-471-46886-8.
- ^ O'Connor, J.J.; Robertson, E.F. (August 2006). "Étienne Pascal". University of St. Andrews, Scotland. Archived from the original on 19 April 2010. Retrieved 5 February 2010.
- ^ "Pendulum". Miriam Webster's Collegiate Encyclopedia. Miriam Webster. 2000. p. 1241. ISBN 978-0-87779-017-4.
- ^ "Petroleum Engineers: Occupational Outlook Handbook: U.S. Bureau of Labor Statistics". www.bls.gov. Retrieved 2018-02-06.
- ^ Modell, Michael; Robert C. Reid (1974). Thermodynamics and Its Applications. Englewood Cliffs, NJ: Prentice-Hall. ISBN 978-0-13-914861-3.
- ^ Enrico Fermi (25 April 2012). Thermodynamics. Courier Corporation. ISBN 978-0-486-13485-7.
- ^ Clement John Adkins (14 July 1983). Equilibrium Thermodynamics. Cambridge University Press. ISBN 978-0-521-27456-2.
- ^ Ballou, Glen (2005). Handbook for sound engineers (3 ed.). Focal Press, Gulf Professional Publishing. p. 1499. ISBN 978-0-240-80758-4.
- ^ Smith, Joe Mauk (2018). Introduction to chemical engineering thermodynamics. United States of America: McGraw-Hill Education. p. 422. ISBN 978-1-259-69652-7.
- ^ Gibbs, J. W. (1961), Scientific Papers, Dover, New York
- ^ Feynman, Leighton & Sands 1963, p. I-2 "If, in some cataclysm, all [] scientific knowledge were to be destroyed [save] one sentence [...] what statement would contain the most information in the fewest words? I believe it is [...] that all things are made up of atoms – little particles that move around in perpetual motion, attracting each other when they are a little distance apart, but repelling upon being squeezed into one another ..."
- ^ Maxwell 1878, p. 9 "Physical science is that department of knowledge which relates to the order of nature, or, in other words, to the regular succession of events."
- ^ Young & Freedman 2014, p. 1 "Physics is one of the most fundamental of the sciences. Scientists of all disciplines use the ideas of physics, including chemists who study the structure of molecules, paleontologists who try to reconstruct how dinosaurs walked, and climatologists who study how human activities affect the atmosphere and oceans. Physics is also the foundation of all engineering and technology. No engineer could design a flat-screen TV, an interplanetary spacecraft, or even a better mousetrap without first understanding the basic laws of physics. (...) You will come to see physics as a towering achievement of the human intellect in its quest to understand our world and ourselves."
- ^ Young & Freedman 2014, p. 2 "Physics is an experimental science. Physicists observe the phenomena of nature and try to find patterns that relate these phenomena."
- ^ Holzner 2006, p. 7 "Physics is the study of your world and the world and universe around you."
- ^ International Bureau of Weights and Measures (2019-05-20), SI Brochure: The International System of Units (SI) (PDF) (9th ed.), p. 131, ISBN 978-92-822-2272-0
- ^ "2018 CODATA Value: Planck constant". The NIST Reference on Constants, Units, and Uncertainty. NIST. 20 May 2019. Retrieved 2021-04-28.
- ^ "Resolutions of the 26th CGPM" (PDF). BIPM. 2018-11-16. Archived from the original (PDF) on 2018-11-19. Retrieved 2018-11-20.
- ^ Goldston, R.J.; Rutherford, P.H. (1995). Introduction to Plasma Physics. Taylor & Francis. p. 1−2. ISBN 978-0-7503-0183-1.
- ^ Morozov, A.I. (2012). Introduction to Plasma Dynamics. CRC Press. p. 17. ISBN 978-1-4398-8132-3.
- ^ Lubliner, J. (2008). Plasticity theory. Dover. ISBN 978-0-486-46290-5.
- ^ Bigoni, D. (2012). Nonlinear Solid Mechanics: Bifurcation Theory and Material Instability. Cambridge University Press. ISBN 978-1-107-02541-7.
- ^ Smith, Clare (2001). Environmental Physics. London: Routledge. ISBN 0-415-20191-8.
- ^ Fowle, Frederick E., ed. (1921). Smithsonian Physical Tables (7th revised ed.). Washington, D.C.: Smithsonian Institution. OCLC 1142734534. Archived from the original on 23 April 2020.
Power or Activity is the time rate of doing work, or if W represents work and P power, P = dw/dt. (p. xxviii) ... ACTIVITY. Power or rate of doing work; unit, the watt. (p. 435)
- ^ Heron, C. A. (1906). "Electrical Calculations for Rallway Motors". Purdue Eng. Rev. (2): 77–93. Archived from the original on 23 April 2020. Retrieved 23 April 2020.
The activity of a motor is the work done per second, ... Where the joule is employed as the unit of work, the international unit of activity is the joule-per-second, or, as it is commonly called, the watt. (p. 78)
- ^ "Societies and Academies". Nature. 66 (1700): 118–120. 1902. doi:10.1038/066118b0.
If the watt is assumed as unit of activity...
- ^ Knight, PhD, Randall D. (2007). "Fluid Mechanics". Physics for Scientists and Engineers: A Strategic Approach (google books) (2nd ed.). San Francisco: Pearson Addison Wesley. p. 1183. ISBN 978-0-321-51671-8. Retrieved 6 April 2020.
Pressure itself is not a Force, even though we sometimes talk "informally" about the "force exerted by the pressure. The correct statement is that the Fluid exerts a force on a surface. In addition, Pressure is a scalar, not a vector.
- ^ "Kendall's Advanced Theory of Statistics, Volume 1: Distribution Theory", Alan Stuart and Keith Ord, 6th Ed, (2009), ISBN 978-0-534-24312-8.
- ^ William Feller, An Introduction to Probability Theory and Its Applications, (Vol 1), 3rd Ed, (1968), Wiley, ISBN 0-471-25708-7.
- ^ Everitt, Brian. (2006). The Cambridge dictionary of statistics (3rd ed.). Cambridge, UK: Cambridge University Press. ISBN 978-0-511-24688-3. OCLC 161828328.
- ^ Ash, Robert B. (2008). Basic probability theory (Dover ed.). Mineola, N.Y.: Dover Publications. pp. 66–69. ISBN 978-0-486-46628-6. OCLC 190785258.
- ^ Renn, J., Damerow, P., and McLaughlin, P. Aristotle, Archimedes, Euclid, and the Origin of Mechanics: The Perspective of Historical Epistemology. Berlin: Max Planck Institute for the History of Science, 2010, pg 1-2.
- ^ Ross, Sheldon M. (2010). A first course in probability. Pearson.
- ^ Inferring From Data
- ^ "Why is quantum mechanics based on probability theory?". StackExchange. July 1, 2014.[unreliable source?]
- ^ Pump classifications. Fao.org. Retrieved on 2011-05-25.
- ^ Peskin, M.; Schroeder, D. (1995). An Introduction to Quantum Field Theory. Westview Press. ISBN 978-0-201-50397-5.
- ^ Feynman, Richard; Leighton, Robert; Sands, Matthew (1964). The Feynman Lectures on Physics, Vol. 3. California Institute of Technology. ISBN 978-0201500646. Retrieved 2020-12-19.
- ^ Dana, Edward Salisbury (1922). A text-book of mineralogy: with an extended treatise on crystallography... New York, London(Chapman Hall): John Wiley and Sons. pp. 195–200, 316.
- ^ Schetz, Joseph A.; Allen E. Fuhs (1999-02-05). Fundamentals of fluid mechanics. Wiley, John & Sons, Incorporated. pp. 111, 142, 144, 147, 109, 155, 157, 160, 175. ISBN 0-471-34856-2.
- ^ Institute of Electrical and Electronics Engineers (1990) IEEE Standard Computer Dictionary: A Compilation of IEEE Standard Computer Glossaries. New York, NY ISBN 1-55937-079-3
- ^ Lowrie, William (2007). Fundamentals of Geophysics. Cambridge University Press. pp. 254–55. ISBN 978-05-2185-902-8. Retrieved March 24, 2019.
- ^ Kumar, Narinder (2003). Comprehensive Physics for Class XII. New Delhi: Laxmi Publications. pp. 280–84. ISBN 978-81-7008-592-8. Retrieved March 24, 2019.
- ^ Bogatin, Eric (2004). Signal Integrity: Simplified. Prentice Hall Professional. p. 114. ISBN 978-0-13-066946-9. Retrieved March 24, 2019.
- ^ W. R. Schowalter (1978) Mechanics of Non-Newtonian Fluids Pergamon ISBN 0-08-021778-8
- ^ Andy Ruina and Rudra Pratap (2015). Introduction to Statics and Dynamics. Oxford University Press. (link: [1])
- ^ "German National Library". International classification system of the German National Library (GND).
- ^ Jump up to: a b A Dictionary of Physics (6 ed.). Oxford University Press. 2009. ISBN 9780199233991.
- ^ Thompson, Sylvanus P. (1965). Calculus Made Easy. Macmillan International Higher Education. p. 185. ISBN 9781349004874. Retrieved 5 July 2020.
- ^ Jones, Alan R. (2018). Probability, Statistics and Other Frightening Stuff. Routledge. p. 48. ISBN 9781351661386. Retrieved 5 July 2020.
- ^ Atkins, Tony; Escudier, Marcel (2013). A Dictionary of Mechanical Engineering. Oxford University Press. ISBN 9780199587438.
- ^ http://hyperphysics.phy-astr.gsu.edu/hbase/rotq.html
- ^ "Safe Failure Fraction". ScienceDirect. Retrieved 21 September 2020.
- ^ "Transport - Transport - UNECE". Unece.org. Retrieved 22 December 2017.
- ^ Mosby's Medical, Nursing & Allied Health Dictionary, Fourth Edition, Mosby-Year Book Inc., 1994, p. 1394
- ^ Lay, David C. (2006). Linear Algebra and Its Applications (3rd ed.). Addison–Wesley. ISBN 0-321-28713-4.
- ^ Strang, Gilbert (2006). Linear Algebra and Its Applications (4th ed.). Brooks Cole. ISBN 0-03-010567-6.
- ^ Axler, Sheldon (2002). Linear Algebra Done Right (2nd ed.). Springer. ISBN 0-387-98258-2.
- ^ Dummit, David S.; Foote, Richard M. (2004). Abstract Algebra (3rd ed.). John Wiley & Sons. ISBN 0-471-43334-9.
- ^ Lang, Serge (2002). Algebra. Graduate Texts in Mathematics. Springer. ISBN 0-387-95385-X.
- ^ Jump up to: a b Young, James F. (2000). "Basic Mechanics". ELEC 201:Introduction to Engineering Design. Electrical and Computer Engineering Dept., Rice Univ. Retrieved 2011-03-29.
- ^ Morris, William, Ed. (1979). The American Heritage Dictionary, New College Edition. USA: Houghton Mifflin. pp. 1167. ISBN 0-395-20360-0.
- ^ "Screw". How Stuff Works website. Discovery Communications. 2011. Retrieved 2011-03-29.
- ^ Collins, Jack A.; Henry R. Busby; George H. Staab (2009). Mechanical Design of Machine Elements and Machines, 2nd Ed. USA: John Wiley and Sons. pp. 462–463. ISBN 978-0-470-41303-6.
- ^ Bhandari, V. B. (2007). Design of machine elements. New Delhi: Tata McGraw-Hill. pp. 202–206. ISBN 978-0-07-061141-2.
- ^ "Signs of dark matter may point to mirror matter candidate".
- ^ Higdon, Ohlsen, Stiles and Weese (1960), Mechanics of Materials, article 4-9 (2nd edition), John Wiley & Sons, Inc., New York. Library of Congress CCN 66-25222
- ^ However, the definition of thermal infrared may start at wavelengths as short as 1.1μm (longer than which optical instruments have difficulty measuring) or anywhere between 2.0μm and 4.0μm, depending on the method of measurement and its purpose.
- ^ L. Chen, G. Yan, T. Wang, H. Ren, J. Calbó, J. Zhao, R. McKenzie (2012), Estimation of surface shortwave radiation components under all sky conditions: Modeling and sensitivity analysis, Remote Sensing of Environment, 123: 457–469.
- ^ Sengupta, Nandini; Sahidullah, Md; Saha, Goutam (August 2016). "Lung sound classification using cepstral-based statistical features". Computers in Biology and Medicine. 75 (1): 118–129. doi:10.1016/j.compbiomed.2016.05.013. PMID 27286184.
- ^ Alan V. Oppenheim and Ronald W. Schafer (1989). Discrete-Time Signal Processing. Prentice Hall. p. 1. ISBN 0-13-216771-9.
- ^ Paul, Akshoy; Roy, Pijush; Mukherjee, Sanchayan (2005), Mechanical sciences: engineering mechanics and strength of materials, Prentice Hall of India, p. 215, ISBN 978-81-203-2611-8.
- ^ Asimov, Isaac (1988), Understanding Physics, New York: Barnes & Noble, p. 88, ISBN 978-0-88029-251-1.
- ^ Anderson, William Ballantyne (1914). Physics for Technical Students: Mechanics and Heat. New York: McGraw Hill. p. 112. Retrieved 2008-05-11.
- ^ "Mechanics". Encyclopædia Britannica. 3. John Donaldson. 1773. p. 44. Retrieved 5 April 2020.
- ^ Morris, Christopher G. (1992). Academic Press Dictionary of Science and Technology. Gulf Professional Publishing. p. 1993. ISBN 9780122004001.
- ^ Jump up to: a b Wildi, Theodore (2002). Electrical Machines, Drives and Power Systems. Pearson. p. 137. ISBN 978-0-13-093083-5.
- ^ Albert Einstein (1905) "Zur Elektrodynamik bewegter Körper", Annalen der Physik 17: 891; English translation On the Electrodynamics of Moving Bodies by George Barker Jeffery and Wilfrid Perrett (1923); Another English translation On the Electrodynamics of Moving Bodies by Megh Nad Saha (1920).
- ^ Griffiths, David J. (2013). "Electrodynamics and Relativity". Introduction to Electrodynamics (4th ed.). Pearson. Chapter 12. ISBN 978-0-321-85656-2.
- ^ Jackson, John D. (1999). "Special Theory of Relativity". Classical Electrodynamics (3rd ed.). John Wiley & Sons, Inc. Chapter 11. ISBN 0-471-30932-X.
- ^ Babrauskas, Vytenis (2003). Ignition Handbook. Society of Fire Protection Engineerslocation=Boston p.369. ISBN 978-0-9728111-3-2.
- ^ Clancy, L.J., Aerodynamics, Section 3.5
- ^ Stagnation Pressure at Eric Weisstein's World of Physics (Wolfram Research)
- ^ "Oxford Reference".
- ^ Romijn, Jan-Willem (2014). "Philosophy of statistics". Stanford Encyclopedia of Philosophy.
- ^ "Cambridge Dictionary".
- ^ Dodge, Y. (2006) The Oxford Dictionary of Statistical Terms, Oxford University Press. ISBN 0-19-920613-9
- ^ Chegg Study chegg.com Retrieved August 2021
- ^ Bohren, Craig F.; Huffman, Donald R. (1998). Absorption and scattering of light by small particles. Wiley. pp. 123–126. ISBN 978-0-471-29340-8.
- ^ Narimanov, Evgenii E.; Smolyaninov, Igor I. (2012). "Beyond Stefan–Boltzmann Law: Thermal Hyper-Conductivity". Conference on Lasers and Electro-Optics 2012. OSA Technical Digest. Optical Society of America. pp. QM2E.1. CiteSeerX 10.1.1.764.846. doi:10.1364/QELS.2012.QM2E.1. ISBN 978-1-55752-943-5. S2CID 36550833.
- ^ Baumgart F. (2000). "Stiffness--an unknown world of mechanical science?". Injury. Elsevier. 31: 14–84. doi:10.1016/S0020-1383(00)80040-6.
Stiffness" = "Load" divided by "Deformation
- ^ Martin Wenham (2001), "Stiffness and flexibility", 200 science investigations for young students, p. 126, ISBN 978-0-7619-6349-3
- ^ Degarmo, Black & Kohser 2003, p. 60 .
- ^ Van Melick, H. G. H.; Govaert, L. E.; Meijer, H. E. H. (2003), "On the origin of strain hardening in glassy polymers", Polymer, 44 (8): 2493–2502, doi:10.1016/s0032-3861(03)00112-5
- ^ Swenson, C. A. (1955), "Properties of Indium and Thallium at low temperatures", Physical Review, 100 (6): 1607–1614, doi:10.1103/physrev.100.1607
- ^ Smith & Hashemi 2006, p. 246 .
- ^ "Science Direct: Structural Analysis" Archived 2021-05-16 at the Wayback Machine
- ^ ASCE/SEI 7-05 Minimum Design Loads for Buildings and Other Structures. American Society of Civil Engineers. 2006. p. 1. ISBN 0-7844-0809-2.
- ^ "1.5.3.1". Eurocode 0: Basis of structural design EN 1990. Bruxelles: European Committee for Standardization. 2002.
- ^ Avallone, E.A.; Baumeister, T. (eds.). Mark's Standard Handbook for Mechanical Engineers (10th ed.). McGraw-Hill. pp. 11–42. ISBN 0-07-004997-1.
- ^ "Sublimate". Merriam-Webster Dictionary.
- ^ Whitten, Kenneth W.; Gailey, Kenneth D.; Davis, Raymond E. (1992). General chemistry (4th ed.). Saunders College Publishing. p. 475. ISBN 0-03-072373-6.
- ^ Boreyko, Jonathan B.; Hansen, Ryan R.; Murphy, Kevin R.; Nath, Saurabh; Retterer, Scott T.; Collier, C. Patrick (2016). "Controlling condensation and frost growth with chemical micropatterns". Scientific Reports. 6: 19131. Bibcode:2016NatSR...619131B. doi:10.1038/srep19131. PMC 4726256. PMID 26796663.
- ^ "Sublime". Dictionary.com Unabridged. Random House.
- ^ Brooks, R. (1986). "A robust layered control system for a mobile robot". IEEE Journal of Robotics and Automation. 2 (1): 14–23. doi:10.1109/JRA.1986.1087032. hdl:1721.1/6432.
- ^ Brooks, R. (1986). "Asynchronous distributed control system for a mobile robot.". SPIE Conference on Mobile Robots. pp. 77–84.
- ^ Brooks, R. A., "A Robust Programming Scheme for a Mobile Robot", Proceedings of NATO Advanced Research Workshop on Languages for Sensor-Based Control in Robotics, Castelvecchio Pascoli, Italy, September 1986.
- ^ John Bardeen; Leon Cooper; J. R. Schriffer (December 1, 1957). Theory of Superconductivity. Physical Review. 108. p. 1175. Bibcode:1957PhRv..108.1175B. doi:10.1103/physrev.108.1175. ISBN 978-0-677-00080-0. Retrieved June 6, 2014. reprinted in Nikolaĭ Nikolaevich Bogoliubov (1963) The Theory of Superconductivity, Vol. 4, CRC Press, ISBN 0677000804, p. 73
- ^ John Daintith (2009). The Facts on File Dictionary of Physics (4th ed.). Infobase Publishing. p. 238. ISBN 978-1-4381-0949-7.
- ^ John C. Gallop (1990). SQUIDS, the Josephson Effects and Superconducting Electronics. CRC Press. pp. 1, 20. ISBN 978-0-7503-0051-3.
- ^ Durrant, Alan (2000). Quantum Physics of Matter. CRC Press. pp. 102–103. ISBN 978-0-7503-0721-5.
- ^ Wentorf, R. H.; Devries, R. C.; Bundy, F. P. (1980). "Sintered Superhard Materials". Science. 208 (4446): 873–80. doi:10.1126/science.208.4446.873. PMID 17772811. S2CID 34588568.
- ^ Fischer-Cripps, Anthony C. (2004) Nanoindentation. Springer. ISBN 0-387-22045-3. p. 198
- ^ Veprek, S.; Zeer, A. and Riedel, R. (2000) in Handbook of Ceramic Hard Materials, R. Riedel (ed.). Wiley, Weinheim. ISBN 3-527-29972-6
- ^ Dubrovinskaia, N.; Dubrovinsky, L.; Solozhenko, V. L. (2007). "Comment on "Synthesis of Ultra-Incompressible Superhard Rhenium Diboride at Ambient Pressure"". Science. 318 (5856): 1550c. Bibcode:2007Sci...318.1550D. doi:10.1126/science.1147650. PMID 18063772.
- ^ Weisstein, Eric W. "Chain Rule". Wolfram MathWorld. Wolfram Research. Retrieved 2 August 2016.
- ^ Larry C. Andrews; Ronald L. Phillips (2003). Mathematical Techniques for Engineers and Scientists. SPIE Press. p. 164. ISBN 978-0-8194-4506-3.
- ^ Ch V Ramana Murthy; NC Srinivas (2001). Applied Mathematics. New Delhi: S. Chand & Co. p. 337. ISBN 978-81-219-2082-7.
- ^ Jastrzebski, D. (1959). Nature and Properties of Engineering Materials (Wiley International ed.). John Wiley & Sons, Inc.
- ^ Jump up to: a b "Generic MMPDS Mechanical Properties Table". stressebook.com. 6 December 2014. Archived from the original on 1 December 2017. Retrieved 27 April 2018.
- ^ Jump up to: a b Degarmo, Black & Kohser 2003, p. 31
- ^ Jump up to: a b Smith & Hashemi 2006, p. 223
- ^ Czichos, Horst (2006). Springer Handbook of Materials Measurement Methods. Berlin: Springer. pp. 303–304. ISBN 978-3-540-20785-6.
- ^ Davis, Joseph R. (2004). Tensile testing (2nd ed.). ASM International. ISBN 978-0-87170-806-9.
- ^ Davis 2004, p. 33.
- ^ Einstein A. (1916), (Translation 1920), New York: H. Holt and Company
- ^ Einstein, Albert (November 28, 1919). "Time, Space, and Gravitation" . The Times.
- ^ Will, Clifford M (2010). "Relativity". Grolier Multimedia Encyclopedia. Retrieved 2010-08-01.
- ^ William D. Stevenson, Jr. Elements of Power System Analysis Third Edition, McGraw-Hill, New York (1975). ISBN 0-07-061285-4, p. 2
- ^ Serway, R. A. and Jewett, Jr. J.W. (2003). Physics for Scientists and Engineers. 6th Ed. Brooks Cole. ISBN 0-534-40842-7.
- ^ Jump up to: a b "Toughness", NDT Education Resource Center, Brian Larson, editor, 2001–2011, The Collaboration for NDT Education, Iowa State University
- ^ Askeland, Donald R. The science and engineering of materials. Wright, Wendelin J. (Seventh ed.). Boston, MA. p. 208. ISBN 978-1-305-07676-1. OCLC 903959750.
- ^ Metha, Rohit. "11". The Principles of Physics. p. 378.
- ^ Agarwal, Anant. Foundations of Analog and Digital Electronic Circuits.Department of Electrical Engineering and Computer Science, Massachusetts Institute of Technology, 2005, p. 43
- ^ Winer, Ethan (2013). "Part 3". The Audio Expert. New York and London: Focal Press. ISBN 978-0-240-82100-9.
- ^ Klein, Christian Felix (1924) [1902]. Elementarmathematik vom höheren Standpunkt aus: Arithmetik, Algebra, Analysis (in German). 1 (3rd ed.). Berlin: J. Springer.
- ^ Klein, Christian Felix (2004) [1932]. Elementary Mathematics from an Advanced Standpoint: Arithmetic, Algebra, Analysis. Translated by Hedrick, E. R.; Noble, C. A. (Translation of 3rd German ed.). Dover Publications, Inc. / The Macmillan Company. ISBN 978-0-48643480-3. Archived from the original on 2018-02-15. Retrieved 2017-08-13.
- ^ "Comprehensive List of Algebra Symbols". Math Vault. 2020-03-25. Retrieved 2020-08-29.
- ^ R. Nagel (ed.), Encyclopedia of Science, 2nd Ed., The Gale Group (2002)
- ^ Boyer (1991), p. [page needed].
- ^ Jump up to: a b IUPAC, Compendium of Chemical Terminology, 2nd ed. (the "Gold Book") (1997). Online corrected version: (1994) "Triple point". doi:10.1351/goldbook.T06502.
- ^ Compare 85 J/(K·mol) in David Warren Ball (20 August 2002). Physical Chemistry. ISBN 9780534266585. and 88 J/(K·mol) in Daniel L. Reger; Scott R. Goode; David W. Ball (27 January 2009). Chemistry: Principles and Practice. ISBN 9780534420123.
- ^ "Definition of TRUSS".
- ^ Plesha, Michael E.; Gray, Gary L.; Costanzo, Francesco (2013). Engineering Mechanics: Statics (2nd ed.). New York: McGraw-Hill Companies Inc. pp. 364–407. ISBN 978-0-07-338029-2.
- ^ Munson, Bruce Roy, T. H. Okiishi, and Wade W. Huebsch. "Turbomachines." Fundamentals of Fluid Mechanics. 6th ed. Hoboken, NJ: J. Wiley & Sons, 2009. Print.
- ^ Logan, Earl. "Handbook of turbomachinery". 1995. Marcel Deckker.
- ^ Vandad Talimi (Original author unknown). "Mechanical Equipment and Systems". 2013. Memorial University of Newfoundland. http://www.engr.mun.ca/~yuri/Courses/MechanicalSystems/Turbomachinery.pdf
- ^ Batchelor, G. (2000). Introduction to Fluid Mechanics.
- ^ Sen, D. (2014). "The Uncertainty relations in quantum mechanics" (PDF). Current Science. 107 (2): 203–218.
- ^ Venes D (2001). Taber's Cyclopedic Medical Dictionary (Twentieth ed.). Philadelphia: F.A. Davis Company. p. 2287. ISBN 0-9762548-3-2.
- ^ Schulz-Vogt HN (2006). "Vacuoles". Inclusions in Prokaryotes. Microbiology Monographs. 1. pp. 295–298. doi:10.1007/3-540-33774-1_10. ISBN 978-3-540-26205-3.
- ^ Brooker RJ, Widmaier EP, Graham LE, Stiling PD (2007). Biology (First ed.). New York: McGraw-Hill. p. 79. ISBN 978-0-07-326807-1.
- ^ Partington, James Riddick (1921). A text-book of inorganic chemistry for university students (1st ed.). OL 7221486M.
- ^ Murrell, J. N.; Kettle, S. F. A.; Tedder, J. M. (1985). The Chemical Bond (2nd ed.). John Wiley & Sons. ISBN 0-471-90759-6.
- ^ Jump up to: a b c d Silbey, Robert J.; Alberty, Robert A.; Bawendi, Moungi G. (2004). Physical Chemistry (4th ed.). Wiley. ISBN 978-0471215042.
- ^ Biography on Nobel prize website. Nobelprize.org (1 March 1911). Retrieved on 2013-11-08.
- ^ Meyers and Chawla (1999): "Mechanical Behavior of Materials", 98-103.
- ^ "viscosity". Merriam-Webster Dictionary.
- ^ Symon, Keith (1971). Mechanics (3rd ed.). Addison-Wesley. ISBN 978-0-201-07392-8.
- ^ Ciletti, M. D., Irwin, J. D., Kraus, A. D., Balabanian, N., Bickard, T. A., and Chan, S. P. (1993). Linear circuit analysis. In Electrical Engineering Handbook, edited by R. C. Dorf. Boca Raton: CRC Press. (pp.82–87)
- ^ IEEE 100 : the authoritative dictionary of IEEE standards terms.-7th ed. ISBN 0-7381-2601-2, page 23
- ^ SI Brochure, 8th ed.
- ^ Council Directive on units of measurements 80/181/EEC Chapter 1.2.3., p. 6: "Special names for the unit of power: the name volt–ampere (symbol ‘VA’) when it is used to express the apparent power of alternating electric current, and var (symbol ‘var’) when it is used to express reactive electric power."
- ^ IUPAC Gold Book, definition of contact (Volta) potential difference.
- ^ Jump up to: a b International Bureau of Weights and Measures (2006), The International System of Units (SI) (PDF) (8th ed.), ISBN 92-822-2213-6, archived from the original (PDF) on 2017-08-14, p. 144
- ^ "Von Mises Criterion (Maximum Distortion Energy Criterion)". Engineer's edge. Retrieved 8 February 2018.
- ^ von Mises, R. (1913). Mechanik der festen Körper im plastisch deformablen Zustand. Göttin. Nachr. Math. Phys., vol. 1, pp. 582–592.
- ^ Pragnan Chakravorty, "What Is a Signal? [Lecture Notes]," IEEE Signal Processing Magazine, vol. 35, no. 5, pp. 175-177, Sept. 2018. https://doi.org/10.1109/MSP.2018.2832195
- ^ Hecht, Eugene (1987). Optics (2nd ed.). Addison Wesley. pp. 15–16. ISBN 978-0-201-11609-0.
- ^ Brian Hilton Flowers (2000). "§21.2 Periodic functions". An introduction to numerical methods in C++ (2nd ed.). Cambridge University Press. p. 473. ISBN 978-0-19-850693-5.
- ^ Raymond A. Serway; John W. Jewett (2006). Principles of physics (4th ed.). Cengage Learning. pp. 404, 440. ISBN 978-0-534-49143-7.
- ^ A. A. Sonin (1995). The surface physics of liquid crystals. Taylor & Francis. p. 17. ISBN 978-2-88124-995-2.
- ^ Keqian Zhang & Dejie Li (2007). Electromagnetic Theory for Microwaves and Optoelectronics. Springer. p. 533. ISBN 978-3-540-74295-1.
- ^ Bowser, Edward Albert (1920), An elementary treatise on analytic mechanics: with numerous examples (25th ed.), D. Van Nostrand Company, pp. 202–203.
- ^ McGraw-Hill Concise Encyclopedia of Science & Technology, Third Ed., Sybil P. Parker, ed., McGraw-Hill, Inc., 1992, p. 2041.
- ^ Wheel and Axle, The World Book Encyclopedia, World Book Inc., 1998, pp. 280-281
- ^ Dodge, Y (2003) The Oxford Dictionary of Statistical Terms, OUP. ISBN 0-19-920613-9 (entry for "winsorized estimation")
- ^ Degarmo, Black & Kohser 2003, p. 60 .
- ^ Wiktionary
- ^ Wiktionary
- ^ Wiktionary
Categories:
- Engineering
- Engineering disciplines
- Glossaries of science
- Safety
- Glossaries of technology