Molten salt reactor
![]() | This article needs additional citations for verification. (September 2018) |
![]() | This article may be in need of reorganization to comply with Wikipedia's layout guidelines. (August 2018) |
![](http://upload.wikimedia.org/wikipedia/commons/thumb/0/08/Molten_Salt_Reactor.svg/330px-Molten_Salt_Reactor.svg.png)
A molten salt reactor (MSR) is a class of nuclear fission reactor in which the primary nuclear reactor coolant and/or the fuel is a molten salt mixture. A key characteristic of MSRs is their operation at or close to atmospheric pressure, rather than the 75-150 times atmospheric pressure of a typical light-water reactor (LWR), hence reducing the large, expensive containment structures used for LWRs and eliminating hydrogen as a source of explosion risk. Another important benefit of MSRs is that they do not produce dangerous and radioactive fission gases that are under pressure, as they are naturally absorbed into the molten salt. A further key characteristic of MSRs is higher operating temperatures than a traditional LWR, providing higher electricity-generation efficiency, the possibility of grid-storage facilities, economical hydrogen production and, in some cases, process-heat opportunities. Relevant design challenges include the corrosivity of hot salts and the changing chemical composition of the salt as it is transmuted by reactor radiation. MSR cost estimations are uncertain but comparable to or cheaper than LWRs.[1] In the specific case of the stable salt reactor (SSR) where the radioactive fuel is contained as a molten salt within fuel pins and the primary circuit is not radioactive, operating costs are likely to be lower and corrosion issues easier to eliminate.[2][3]
While many design variants have been proposed, there are three main categories regarding the role of molten salt:
Category | hideExamples |
---|---|
Molten salt fuel - circulating | ARE • AWB • CMSR • DMSR • EVOL • LFTR • IMSR • MSFR • MSRE • DFR • TMSR-500 • TMSR-LF |
Molten salt fuel - static | SSR |
Molten salt coolant only | FHR • TMSR-SF |
(The use of molten salt as fuel and as coolant are independent design choices - the original circulating-fuel-salt MSRE and the more recent static-fuel-salt SSR use salt as fuel and salt as coolant; the DFR uses salt as fuel but metal as coolant; and the FHR has solid fuel but salt as coolant).
MSRs offer multiple advantages over conventional nuclear power plants, although for historical reasons[4] they have not been deployed.
The concept was first established in the 1950s. The early Aircraft Reactor Experiment was primarily motivated by the compact size that the technique offers, while the Molten-Salt Reactor Experiment aimed to prove the concept of a nuclear power plant which implements a thorium fuel cycle in a breeder reactor. Increased research into Generation IV reactor designs began to renew interest in the technology.[5]
History[]
![]() | The examples and perspective in this article may not represent a worldwide view of the subject. (August 2018) |
Aircraft reactor experiment[]
MSR research started with the U.S. Aircraft Reactor Experiment (ARE) in support of the U.S. Aircraft Nuclear Propulsion program. ARE was a 2.5 MWth nuclear reactor experiment designed to attain a high energy density for use as an engine in a nuclear-powered bomber.
The project included experiments, including high temperature and engine tests collectively called the Heat Transfer Reactor Experiments: HTRE-1, HTRE-2 and HTRE-3 at the National Reactor Test Station (now Idaho National Laboratory) as well as an experimental high-temperature molten salt reactor at Oak Ridge National Laboratory – the ARE.
ARE used molten fluoride salt NaF-ZrF4-UF4 (53-41-6 mol%) as fuel, moderated by beryllium oxide (BeO). Liquid sodium was a secondary coolant.
The experiment had a peak temperature of 860 °C. It produced 100 MWh over nine days in 1954. This experiment used Inconel 600 alloy for the metal structure and piping.[6]
An MSR was operated at the Critical Experiments Facility of the Oak Ridge National Laboratory in 1957. It was part of the circulating-fuel reactor program of the Pratt & Whitney Aircraft Company (PWAC). This was called Pratt and Whitney Aircraft Reactor-1 (PWAR-1). The experiment was run for a few weeks and at essentially zero power, although it reached criticality. The operating temperature was held constant at approximately 675 °C (1,250 °F). The PWAR-1 used NaF-ZrF4-UF4 as the primary fuel and coolant. It was one of three critical MSRs ever built.[7]
Molten-Salt Reactor Experiment[]
![](http://upload.wikimedia.org/wikipedia/commons/thumb/9/91/MSRE_Diagram.png/220px-MSRE_Diagram.png)
Oak Ridge National Laboratory (ORNL) took the lead in researching MSRs through the 1960s. Much of their work culminated with the Molten-Salt Reactor Experiment (MSRE). MSRE was a 7.4 MWth test reactor simulating the neutronic "kernel" of a type of epithermal thorium molten salt breeder reactor called the liquid fluoride thorium reactor (LFTR). The large (expensive) breeding blanket of thorium salt was omitted in favor of neutron measurements.
MSRE's piping, core vat and structural components were made from Hastelloy-N, moderated by pyrolytic graphite. It went critical in 1965 and ran for four years. Its fuel was LiF-BeF2-ZrF4-UF4 (65-29-5-1). The graphite core moderated it. Its secondary coolant was FLiBe (2LiF-BeF2). It reached temperatures as high as 650 °C and achieved the equivalent of about 1.5 years of full power operation.
Oak Ridge National Laboratory molten salt breeder reactor[]
The culmination of the ORNL research during the 1970–1976 timeframe resulted in a molten salt breeder reactor (MSBR) design. Fuel was to be LiF-BeF2-ThF4-UF4 (72-16-12-0.4) with graphite moderator. The secondary coolant was to be NaF-NaBF4. Its peak operating temperature was to be 705 °C.[9] It would follow a 4-year replacement schedule. The MSR program closed down in the early 1970s in favor of the liquid metal fast-breeder reactor (LMFBR),[10] after which research stagnated in the United States.[3][11][12] As of 2011, ARE and MSRE remained the only molten-salt reactors ever operated.
The MSBR project received funding from 1968 to 1976 of (in 2019 dollars[13]) $66.4 million.[14]
Officially, the program was cancelled because:
- The political and technical support for the program in the United States was too thin geographically. Within the United States the technology was well understood only in Oak Ridge.[10]
- The MSR program was in competition with the fast breeder program at the time, which got an early start and had copious government development funds with contracts that benefited many parts of the country. When the MSR development program had progressed far enough to justify an expanded program leading to commercial development, the United States Atomic Energy Commission (AEC) could not justify the diversion of substantial funds from the LMFBR to a competing program.[10]
Oak Ridge National Laboratory denatured molten salt reactor (DMSR)[]
Engel et al 1980 "examine the conceptual feasibility of a molten-salt power reactor fueled with denatured uranium-235 (i.e. with low-enriched uranium) and operated with a minimum of chemical processing." The main priority behind the design characteristics was proliferation resistance.[15] Although the DMSR can theoretically be fueled partially by thorium or plutonium, fueling solely with low enriched uranium (LEU) helps maximize proliferation resistance.
Other important goals of the DMSR were to minimize research and development and to maximize feasibility. The Generation IV international Forum (GIF) includes "salt processing" as a technology gap for molten salt reactors.[16] The DMSR requires minimal chemical processing because it is a burner rather than a breeder. Both reactors built at ORNL were burner designs. In addition, the choices to use graphite for neutron moderation and enhanced Hastelloy-N for piping simplified the design and reduced R&D.[citation needed]
Development in the United Kingdom[]
The UK's Atomic Energy Research Establishment (AERE) was developing an alternative MSR design across its National Laboratories at Harwell, Culham, Risley and Winfrith. AERE opted to focus on a lead-cooled 2.5 GWe Molten Salt Fast Reactor (MSFR) concept using a chloride.[17] They also researched helium gas as a coolant.[18][19]
The UK MSFR would be fuelled by plutonium, a fuel considered to be 'free' by the program's research scientists, because of the UK's plutonium stockpile.
Despite their different designs, ORNL and AERE maintained contact during this period with information exchange and expert visits. Theoretical work on the concept was conducted between 1964 and 1966, while experimental work was ongoing between 1968 and 1973. The program received annual government funding of around £100,000–£200,000 (equivalent to £2m–£3m in 2005). This funding came to an end in 1974, partly due to the success of the Prototype Fast Reactor at Dounreay which was considered a priority for funding as it went critical in the same year.[17]
Development in the Soviet Union[]
In the USSR, a molten-salt reactor research program was started in the second half of the 1970s at the Kurchatov Institute. It included theoretical and experimental studies, particularly the investigation of mechanical, corrosion and radiation properties of the molten salt container materials. The main findings supported the conclusion that no physical nor technological obstacles prevented the practical implementation of MSRs.[20][21][22]
Twenty-first century[]
MSR interest resumed in the new millennium due to continuing delays in fusion power and other nuclear power programs and increasing demand for energy sources that would incur minimal greenhouse gas (GHG) emissions.[3][23]
The LFTR design was strongly supported by Alvin Weinberg, who patented the light-water reactor and was a director of the U.S.'s Oak Ridge National Laboratory. In 2016 Nobel prize winning physicist Carlo Rubbia, former Director General of CERN, claimed that one of the main reasons why research was cut is that thorium is difficult to turn into a nuclear weapon.[4]
Thorium is not for tomorrow but unless you do any development, it will not get there.
— Dr Carlo Rubbia, Nobel Laureate and former Director General of CERN, January 2016[4]
Commercial/national/international projects[]
Canada[]
Terrestrial Energy, a Canadian-based company, is developing a DMSR design called the Integral Molten Salt Reactor (IMSR). The IMSR is designed to be deployable as a small modular reactor (SMR). Their design currently undergoing licensing is 400MW thermal (190MW electrical). With high operating temperatures, the IMSR has applications in industrial heat markets as well as traditional power markets. The main design features include neutron moderation from graphite, fueling with low-enriched uranium and a compact and replaceable Core-unit. Decay heat is removed passively using nitrogen (with air as an emergency alternative). The latter feature permits the operational simplicity necessary for industrial deployment.[24]
Terrestrial completed the first phase of a prelicensing review by the Canadian Nuclear Safety Commission in 2017, which provided a regulatory opinion that the design features are generally safe enough to eventually obtain a license to construct the reactor.[25]
China[]
China initiated a thorium research project in January 2011.[26] A 100 MW demonstrator of the solid fuel version (TMSR-SF), based on pebble bed technology, was planned to be ready by 2024. A 10 MW pilot and a larger demonstrator of the liquid fuel (TMSR-LF) variant were targeted for 2024 and 2035, respectively.[27][28] China then accelerated its program to build two 12 MW reactors underground at Wuwei research facilities by 2020,[29] beginning with the 2 megawatt TMSR-LF1 prototype.[30] The project sought to test new corrosion-resistant materials.[29] In 2017, ANSTO/Shanghai Institute Of Applied Physics announced the creation of a NiMo-SiC alloy for use in MSRs.[31][32] In 2021 China stated that Wuwei prototype operation could start power generation from thorium in September.[33] The 100 MW successor was expected to 3 meters tall and 2.5 meters wide.[34]
Denmark[]
Copenhagen Atomics is a Danish molten salt technology company developing mass manufacturable molten salt reactors. The Copenhagen Atomics Waste Burner is a single-fluid, heavy water moderated, fluoride-based, thermal spectrum and autonomously controlled molten salt reactor. This is designed to fit inside of a leak-tight, 40-foot, stainless steel shipping container. The heavy water moderator is thermally insulated from the salt and continuously drained and cooled to below 50 °C. A molten lithium-7 deuteroxide (7LiOD) moderator version is also being researched. The reactor utilizes the thorium fuel cycle using separated plutonium from spent nuclear fuel as the initial fissile load for the first generation of reactors, eventually transitioning to a thorium breeder.[35] Copenhagen Atomics is actively developing and testing valves, pumps, heat exchangers, measurement systems, salt chemistry and purification systems, and control systems and software for molten salt applications.[36]
Seaborg Technologies is developing the core for a compact molten salt reactor (CMSR). The CMSR is a high temperature, single salt, thermal MSR designed to go critical on commercially available low enriched uranium. The CMSR design is modular, and uses proprietary NaOH moderator.[3][37] The reactor core is estimated to be replaced every 12 years. During operation, the fuel will not be replaced and will burn for the entire 12-year reactor lifetime. The first version of the Seaborg core is planned to produce 250 MWth power and 100 MWe power. As a power plant, the CMSR will be able to deliver electricity, clean water and heating/cooling to around 200,000 households.[38]
France[]
The CNRS project EVOL (Evaluation and viability of liquid fuel fast reactor system) project, with the objective of proposing a design of the molten salt fast reactor (MSFR),[39] released its final report in 2014.[40] Various MSR projects like FHR, MOSART, MSFR, and TMSR have common research and development themes.[41]
The EVOL project will be continued by the EU-funded Safety Assessment of the Molten Salt Fast Reactor (SAMOFAR) project, in which several European research institutes and universities collaborate.[42]
Germany[]
The German Institute for Solid State Nuclear Physics in Berlin has proposed the dual fluid reactor as a concept for a fast breeder lead-cooled MSR. The original MSR concept used the fluid salt to provide the fission materials and also to remove the heat. Thus it had problems with the needed flow speed. Using 2 different fluids in separate circles solves the problem.[citation needed]
India[]
In 2015, Indian researchers published a MSR design,[43] as an alternative path to thorium-based reactors, according to India's three-stage nuclear power programme.[44]
Indonesia[]
is developing the TMSR-500 molten salt reactor for the Indonesian market.
Japan[]
The Fuji Molten Salt Reactor is a 100 to 200 MWe LFTR, using technology similar to the Oak Ridge project. A consortium including members from Japan, the U.S. and Russia are developing the project. The project would likely take 20 years to develop a full size reactor,[45] but the project seems to lack funding.[46]
Russia[]
In 2020, Rosatom announced plans to build a 10 MWth FLiBe burner MSR. It would be fueled by plutonium from reprocessed VVER spent nuclear fuel and fluorides of minor actinides. It is expected to launch in 2031 at Mining and Chemical Combine.[47][48]
United Kingdom[]
The Alvin Weinberg Foundation is a British non-profit organization founded in 2011, dedicated to raising awareness about the potential of thorium energy and LFTR. It was formally launched at the House of Lords on 8 September 2011.[49][50][51] It is named after American nuclear physicist Alvin M. Weinberg, who pioneered thorium MSR research.
The stable salt reactor, designed by Moltex Energy, was selected as the most suitable of six MSR designs for UK implementation in a 2015 study commissioned by the UK's innovation agency, Innovate UK.[52] UK government support has been weak,[53] but Moltex has obtained support from New Brunswick Power for the development of a pilot plant in Point Lepreau, Canada,[54] and financial backing from IDOM (an international engineering firm)[55] and is currently engaged in the Canadian Vendor Design Review process.[56]
United States[]
Idaho National Laboratory designed a molten-salt-cooled, molten-salt-fuelled reactor with a prospective output of 1000 MWe.[57]
Kirk Sorensen, former NASA scientist and chief nuclear technologist at Teledyne Brown Engineering, is a long-time promoter of the thorium fuel cycle, coining the term liquid fluoride thorium reactor. In 2011, Sorensen founded Flibe Energy,[3] a company aimed at developing 20–50 MW LFTR reactor designs to power military bases. (It is easier to approve novel military designs than civilian power station designs in the US nuclear regulatory environment).[58][59][60][61]
Transatomic Power pursued what it termed a waste-annihilating molten salt reactor (WAMSR), intended to consume existing spent nuclear fuel,[62] from 2011 until ceasing operation in 2018.[63]
In January 2016, the United States Department of Energy announced a $80m award fund to develop Generation IV reactor designs.[64] One of the two beneficiaries, Southern Company will use the funding to develop a molten chloride fast reactor (MCFR), a type of MSR developed earlier by British scientists.[17][3]
In 2021, Tennessee Valley Authority (TVA) and Kairos Power announced a TRISO-fed, fluoride salt-cooled 50MWt test reactor would be deployed at Oak Ridge, Tennessee.[65]
Design[]
Nuclear reactors can be categorized in various ways. MSR designs participate in many of those categories. MSRs can be burners or breeders. They can be fast or thermal or epithermal.[66] Thermal reactors typically employ a moderator (usually graphite) to slow the neutrons down and moderate temperature. They can accept a variety of fuels (low-enriched uranium, thorium, depleted uranium, waste products)[67] and coolants (fluoride, chloride, lithium, beryllium, mixed). Fuel cycle can be either closed or once-through.[66] They can be monolithic or modular, large or small. The reactor can adopt a loop, modular or integral configuration. Variations include:
Liquid-salt very-high-temperature reactor[]
(Also referred to as "fluoride salt-cooled high-temperature reactor" (FHR).[68])
This approach involves using a fluoride-salt as the coolant. Both the traditional MSR and the very-high-temperature reactor (VHTR) were selected as potential designs for study under the Generation Four Initiative (GEN-IV). One version of the VHTR under study was the liquid-salt very-high-temperature reactor (LS-VHTR), also commonly called the advanced high-temperature reactor (AHTR).[citation needed]
It uses liquid salt as a coolant in the primary loop, rather than a single helium loop. It relies on "TRISO" fuel dispersed in graphite. Early AHTR research focused on graphite in the form of graphite rods that would be inserted in hexagonal moderating graphite blocks, but current studies focus primarily on pebble-type fuel.[citation needed] The LS-VHTR can work at very high temperatures (the boiling point of most molten salt candidates is >1400 °C); low-pressure cooling that can be used to match hydrogen production facility conditions (most thermochemical cycles require temperatures in excess of 750 °C); better electric conversion efficiency than a helium-cooled VHTR operating in similar conditions; passive safety systems and better retention of fission products in the event of an accident.[citation needed]
Liquid fluoride thorium reactor[]
Reactors containing molten thorium salt, called liquid fluoride thorium reactors (LFTR), would tap the thorium fuel cycle. Private companies from Japan, Russia, Australia and the United States, and the Chinese government, have expressed interest in developing this technology.[26][46][58]
Advocates estimate that five hundred metric tons of thorium could supply U.S. energy needs for one year.[69] The U.S. Geological Survey estimates that the largest-known U.S. thorium deposit, the Lemhi Pass district on the Montana-Idaho border, contains thorium reserves of 64,000 metric tons.[70]
Traditionally, these reactors were known as molten salt breeder reactors (MSBRs) or thorium molten salt reactors (TMSRs), but the name LFTR was promoted as a rebrand in the early 2000s by Kirk Sorensen.
Stable salt reactor[]
The stable salt reactor is a relatively recent concept which holds the molten salt fuel statically in traditional LWR fuel pins. Pumping of the fuel salt, and all the corrosion/deposition/maintenance/containment issues arising from circulating a highly radioactive, hot and chemically complex fluid, are no longer required. The fuel pins are immersed in a separate, non-fissionable fluoride salt which acts as primary coolant.
Coolant[]
MSRs can be cooled in various ways, including using molten salts.
Molten-salt-cooled solid-fuel reactors are variously called "molten salt reactor system" in the Generation IV proposal, molten salt converter reactors (MSCR), advanced high-temperature reactors (AHTRs), or fluoride high-temperature reactors (FHR, preferred DOE designation).[71]
FHRs cannot reprocess fuel easily and have fuel rods that need to be fabricated and validated, requiring up to twenty years[citation needed] from project inception. FHR retains the safety and cost advantages of a low-pressure, high-temperature coolant, also shared by liquid metal cooled reactors. Notably, steam is not created in the core (as is present in BWRs), and no large, expensive steel pressure vessel (as required for PWRs). Since it can operate at high temperatures, the conversion of the heat to electricity can use an efficient, lightweight Brayton cycle gas turbine.
Much of the current research on FHRs is focused on small, compact heat exchangers that reduce molten salt volumes and associated costs.[72]
Molten salts can be highly corrosive and corrosivity increases with temperature. For the primary cooling loop, a material is needed that can withstand corrosion at high temperatures and intense radiation. Experiments show that Hastelloy-N and similar alloys are suited to these tasks at operating temperatures up to about 700 °C. However, operating experience is limited. Still higher operating temperatures are desirable—at 850 °C thermochemical production of hydrogen becomes possible. Materials for this temperature range have not been validated, though carbon composites, molybdenum alloys (e.g. TZM), carbides, and refractory metal based or ODS alloys might be feasible.
A workaround suggested by a private researcher is to use the new beta-titanium Au alloys as this would also allow extreme temperature operation as well as increasing the safety margin.[citation needed]
Dual-fluid molten salt reactors[]
A prototypical example of a dual fluid reactor is the lead-cooled, salt-fueled reactor.
Fused salt selection[]
![](http://upload.wikimedia.org/wikipedia/commons/thumb/d/d4/FLiBe.png/220px-FLiBe.png)
The salt mixtures are chosen to make the reactor safer and more practical.
Fluorine[]
Fluorine has only one stable isotope (F-19), and does not easily become radioactive under neutron bombardment. Compared to chlorine and other halides, fluorine also absorbs fewer neutrons and slows ("moderates") neutrons better. Low-valence fluorides boil at high temperatures, though many pentafluorides and hexafluorides boil at low temperatures. They must be very hot before they break down into their constituent elements. Such molten salts are "chemically stable" when maintained well below their boiling points. Fluoride salts dissolve poorly in water, and do not form burnable hydrogen.
Chlorine[]
Chlorine has two stable isotopes (35
Cl and 37
Cl), as well as a slow-decaying isotope between them which facilitates neutron absorption by 35
Cl.
Chlorides permit fast breeder reactors to be constructed. Much less research has been done on reactor designs using chloride salts. Chlorine, unlike fluorine, must be purified to isolate the heavier stable isotope, chlorine-37, thus reducing production of sulfur tetrachloride that occurs when chlorine-35 absorbs a neutron to become chlorine-36, then degrades by beta decay to sulfur-36.
Lithium[]
Lithium must be in the form of purified 7
Li, because 6
Li effectively captures neutrons and produces tritium. Even if pure 7Li is used, salts containing lithium cause significant tritium production, comparable with heavy water reactors.
Mixtures[]
Reactor salts are usually close to eutectic mixtures to reduce their melting point. A low melting point simplifies melting the salt at startup and reduces the risk of the salt freezing as it is cooled in the heat exchanger.
Due to the high "redox window" of fused fluoride salts, the redox potential of the fused salt system can be changed. Fluorine-lithium-beryllium ("FLiBe") can be used with beryllium additions to lower the redox potential and almost eliminate corrosion. However, since beryllium is extremely toxic, special precautions must be engineered into the design to prevent its release into the environment. Many other salts can cause plumbing corrosion, especially if the reactor is hot enough to make highly reactive hydrogen.
To date, most research has focused on FLiBe, because lithium and beryllium are reasonably effective moderators and form a eutectic salt mixture with a lower melting point than each of the constituent salts. Beryllium also performs neutron doubling, improving the neutron economy. This process occurs when the beryllium nucleus emits two neutrons after absorbing a single neutron. For the fuel carrying salts, generally 1% or 2% (by mole) of UF4 is added. Thorium and plutonium fluorides have also been used.
Material | Total neutron capture relative to graphite (per unit volume) |
Moderating ratio (Avg. 0.1 to 10 eV) |
---|---|---|
Heavy water | 0.2 | 11449 |
ZrH[74][75][76] | ~0.2 | ~0 if <0.14 eV, ~11449 if >0.14 eV |
Light water | 75 | 246 |
Graphite | 1 | 863 |
Sodium | 47 | 2 |
UCO | 285 | 2 |
UO2 | 3583 | 0.1 |
2LiF–BeF2 | 8 | 60 |
LiF–BeF2–ZrF4 (64.5–30.5–5) | 8 | 54 |
NaF–BeF2 (57–43) | 28 | 15 |
LiF–NaF–BeF2 (31–31–38) | 20 | 22 |
LiF–ZrF4 (51–49) | 9 | 29 |
NaF–ZrF4 (59.5–40.5) | 24 | 10 |
LiF-NaF–ZrF4 (26–37–37) | 20 | 13 |
KF–ZrF4 (58–42) | 67 | 3 |
RbF–ZrF4 (58–42) | 14 | 13 |
LiF–KF (50–50) | 97 | 2 |
LiF–RbF (44–56) | 19 | 9 |
LiF–NaF–KF (46.5–11.5–42) | 90 | 2 |
LiF–NaF–RbF (42–6–52) | 20 | 8 |
Fused salt purification[]
Techniques for preparing and handling molten salt were first developed at ORNL.[77] The purpose of salt purification is to eliminate oxides, sulfur and metal impurities. Oxides could result in the deposition of solid particles in reactor operation. Sulfur must be removed because of its corrosive attack on nickel-based alloys at operational temperature. Structural metal such as chromium, nickel, and iron must be removed for corrosion control.
A water content reduction purification stage using HF and helium sweep gas was specified to run at 400 °C. Oxide and sulfur contamination in the salt mixtures were removed using gas sparging of HF – H2 mixture, with the salt heated to 600 °C.[77](p8) Structural metal contamination in the salt mixtures were removed using hydrogen gas sparging, at 700 °C.[77](p26) Solid ammonium hydrofluoride was proposed as a safer alternative for oxide removal.[78]
Fused salt processing[]
The possibility of online processing can be an MSR advantage. Continuous processing would reduce the inventory of fission products, control corrosion and improve neutron economy by removing fission products with high neutron absorption cross-section, especially xenon. This makes the MSR particularly suited to the neutron-poor thorium fuel cycle. Online fuel processing can introduce risks of fuel processing accidents,[79](p15) which can trigger release of radio isotopes.
In some thorium breeding scenarios, the intermediate product protactinium 233
Pa would be removed from the reactor and allowed to decay into highly pure 233
U, an attractive bomb-making material. More modern designs propose to use a lower specific power or a separate thorium breeding blanket. This dilutes the protactinium to such an extent that few protactinium atoms absorb a second neutron or, via a (n, 2n) reaction (in which an incident neutron is not absorbed but instead knocks a neutron out of the nucleus), generate 232
U. Because 232
U has a short half-life and its decay chain contains hard gamma emitters, it makes the isotopic mix of uranium less attractive for bomb-making. This benefit would come with the added expense of a larger fissile inventory or a 2-fluid design with a large quantity of blanket salt.
The necessary fuel salt reprocessing technology has been demonstrated, but only at laboratory scale. A prerequisite to full-scale commercial reactor design is the R&D to engineer an economically competitive fuel salt cleaning system.
Fuel reprocessing[]
![](http://upload.wikimedia.org/wikipedia/commons/thumb/0/02/Changing_composition_molten_salt_reactor-en.svg/330px-Changing_composition_molten_salt_reactor-en.svg.png)
Reprocessing refers to the chemical separation of fissionable uranium and plutonium from spent fuel.[80] Such recovery could increase the risk of nuclear proliferation. In the United States the regulatory regime has varied dramatically across administrations.[80]
In the 1971 molten salt breeder reactor proposal, uranium reprocessing was scheduled every ten days as part of reactor operation.[81](p181) Subsequently, a once-through fueling design was proposed that limited uranium reprocessing to every thirty years at the end of useful salt life.[15](p98) A mixture with 238
U was called for to make sure recovered uranium would not be weapons-grade. This design is referred to as denatured molten salt reactor.[82] With no reprocessing, the uranium would be disposed with other fission products.
Comparison to light water reactors[]
MSRs, especially those with the fuel dissolved in the salt, differ considerably from conventional reactors. Reactor core pressure can be low and the temperature much higher. In this respect an MSR is more similar to a liquid metal cooled reactor than to a conventional light water cooled reactor. MSRs are often planned as breeding reactors with a closed fuel cycle—as opposed to the once-through fuel currently used in U.S. nuclear reactors.
Safety concepts rely on a negative temperature coefficient of reactivity and a large possible temperature rise to limit reactivity excursions. As an additional method for shutdown, a separate, passively cooled container below the reactor can be included. In case of problems and for regular maintenance the fuel is drained from the reactor. This stops the nuclear reaction and acts as a second cooling system. Neutron-producing accelerators have been proposed for some super-safe subcritical experimental designs.[83]
Cost estimates from the 1970s were slightly lower than for conventional light-water reactors.[84]
The temperatures of some proposed designs are high enough to produce process heat for hydrogen production or other chemical reactions. Because of this, they are included in the GEN-IV roadmap for further study.[16]
Advantages[]
MSRs offer many potential advantages over current light water reactors:[9]
- As in all low-pressure reactor designs, passive decay heat removal is achieved in MSRs. In some designs, the fuel and the coolant are the same fluid, so a loss of coolant removes the reactor's fuel, similar to how loss of coolant also removes the moderator in LWRs. Unlike steam, fluoride salts dissolve poorly in water, and do not form burnable hydrogen. Unlike steel and solid uranium oxide, molten salts are not damaged by the core's neutron bombardment, though the reactor vessel still is.
- A low-pressure MSR lacks a BWR's high-pressure radioactive steam and therefore do not experience leaks of radioactive steam and cooling water, and the expensive containment, steel core vessel, piping and safety equipment needed to contain radioactive steam. However, most MSR designs require radioactive fission product-containing fluid in direct contact with pumps and heat exchangers.
- MSRs may make closed nuclear fuel cycles cheaper because they can operate with slow neutrons. If fully implemented, any reactor that closes the nuclear fuel cycle reduces environmental impacts: Chemical separation turns long-lived actinides back into reactor fuel. The discharged wastes are mostly fission products (nuclear ashes) with shorter half-lives. This reduces the needed geologic containment to 300 years rather than the tens of thousands of years needed by a light-water reactor's spent nuclear fuel. It also permits the use of alternate nuclear fuels, such as thorium.
- The fuel's liquid phase might be pyroprocessed to separate fission products (nuclear ashes) from actinide fuels. This may have advantages over conventional reprocessing, though much development is still needed.
- Fuel rod fabrication is not required (replaced with fuel salt synthesis).
- Some designs are compatible with the fast neutron spectrum, which can "burn" problematic transuranic elements like Pu240, Pu241 and up (reactor grade plutonium) from traditional light-water nuclear reactors.
- An MSR can react to load changes in less than 60 seconds (unlike "traditional" solid-fuel nuclear power plants that suffer from xenon poisoning).
- Molten salt reactors can run at high temperatures, yielding high thermal efficiency. This reduces size, expense, and environmental impacts.
- MSRs can offer a high "specific power," that is high power at a low mass as demonstrated by ARE.[6]
- A possibly good neutron economy makes the MSR attractive for the neutron poor thorium fuel cycle
Disadvantages[]
- Little development compared to most Gen IV designs
- In circulating-fuel-salt designs, radionuclides dissolved in fuel come in contact with major equipment such as pumps and heat exchangers, likely requiring fully remote and possibly expensive maintenance.
- Required onsite chemical plant to manage core mixture and remove fission products
- Required regulatory changes to deal with radically different design features
- MSR designs rely on nickel-based alloys to hold the molten salt. Alloys based on nickel and iron are prone to embrittlement under high neutron flux.[15](p83)
- Corrosion risk.[85] Molten salts require careful management of their redox state to handle corrosion risks. This is particularly challenging for circulating-fuel-salt designs, in which a complex mix of fissile/fertile isotopes and their transmutation/fission/decay products is being circulated through the reactor. Static fuel salt designs profit from modularising the problem: the fuel salt is contained within fuel pins whose regular replacement, primarily due to neutron irradiation damage, is part of the operating concept; while the coolant salt has a simpler chemical composition and, under appropriate redox state management, does not pose a corrosion risk either to the fuel pins or to the reactor vessel. (Regarding redox state management, see the descriptions for the stable salt reactor's fuel and coolant salts). The MSRs developed at ORNL in the 60's were only safe to operate for a few years, and operated at only about 650°C. Potential corrosion risks include dissolution of chromium by liquid fluoride thorium salts at >700°C, hence endangering stainless steel components. Neutron radiation can also transmute other common alloying agents such as Co and Ni, shortening lifespan. If using lithium salts (e.g. FLiBe), it is preferable, if expensive, to use 7Li to reduce tritium generation (tritium can permeate stainless steels, cause embrittlement, and escape into the environment). ORNL developed Hastelloy N to help address these issues, and there is an effort to certify other structural steels to for use in reactors (316H, 800H, inco 617).
- As a breeder reactor, a modified MSR might be able to produce weapons-grade nuclear material[86]
- The MSRE and aircraft nuclear reactors used enrichment levels so high that they approach the levels of nuclear weapons. These levels would be illegal in most modern regulatory regimes for power plants. Some modern designs avoid this issue.[87]
- Neutron damage to solid moderator materials can limit the core lifetime of an MSR that uses moderated thermal neutrons. For example, the MSRE was designed so that its graphite moderator sticks had very loose tolerances, so neutron damage could change their size without damage. "Two fluid" MSR designs are unable to use graphite piping because graphite changes size when it is bombarded with neutrons, and graphite pipes would crack and leak.[9] MSR using fast neutrons cannot use graphite anyway to avoid moderation.
- Thermal MSRs have lower breeding ratios than fast-neutron breeders, though their doubling time may be shorter.
See also[]
References[]
- ^ Mignacca, Benito; Locatelli, Giorgio (November 2020). "Economics and finance of Molten Salt Reactors". Progress in Nuclear Energy. 129: 103503. doi:10.1016/j.pnucene.2020.103503.
- ^ "Ian Scott discusses the development of the waste-burning stable salt reactor". The Chemical Engineer.
- ^ Jump up to: a b c d e f Waldrop, M. Mitchell (22 February 2019). "Nuclear goes retro — with a much greener outlook". Knowable Magazine. doi:10.1146/knowable-022219-2.CS1 maint: date and year (link)
- ^ Jump up to: a b c Arkin, Fatima (25 January 2016). "An alternative fuel for nuclear energy looms". Retrieved 15 July 2016.
- ^ "Molten Salt Reactors". World Nuclear Association.
- ^ Jump up to: a b Rosenthal, Murry. An Account of Oak Ridge National Laboratory's Thirteen Nuclear Reactors, ORNL/TM-2009/181.
- ^ Scott, D; Alwang, G W; Demski, E F; Fader, W J; Sandin, E V; Malenfant, R E (14 August 1958). "A Zero Power Reflector-Moderated Reactor Experiment at Elevated Temperature": ORNL–2536, 4673343. doi:10.2172/4673343. OSTI 4673343. Cite journal requires
|journal=
(help) - ^ MSRE Legend: 1) Reactor vessel; 2) Heat exchanger; 3) Molten salt fuel pump; 4) Freeze flange; 5) Thermal shield; 6) Coolant salt pump; 7) Radiator; 8) Coolant salt drain tank; 9) Fans; 10) Fuel salt drain tanks; 11) Flush tank; 12) Vessel; 13) Fuel salt freeze valve. —ORNL-LR-DWG 63-1209R
- ^ Jump up to: a b c Section 5.3, WASH 1097. Energy From Thorium's Document Repository "The Use of Thorium in Nuclear Power Reactors". ORNL.gov
- ^ Jump up to: a b c MacPherson, H. G. (1985). "The Molten Salt Reactor Adventure" (PDF). Nuclear Science and Engineering. 90 (4): 374–380. doi:10.13182/NSE90-374.
- ^ Weinberg, Alvin (1997). The First Nuclear Era: The Life and Times of a Technological Fixer. Springer. ISBN 978-1-56396-358-2.
- ^ "Chapter 6: Responding To Social Needs". ORNL: The First 50 Years. Retrieved 12 November 2011.
- ^ Thomas, Ryland; Williamson, Samuel H. (2020). "What Was the U.S. GDP Then?". MeasuringWorth. Retrieved 22 September 2020. United States Gross Domestic Product deflator figures follow the Measuring Worth series.
- ^ Cohen, Linda R.; Noll, Roger G. (1991). The Technology pork barrel. Brookings Institution. p. 234. ISBN 978-0-8157-1508-5. Retrieved 28 February 2012.
- ^ Jump up to: a b c Engel, J.R.; Bauman, H.F.; Dearing, J.F.; Grimes, W.R.; McCoy, H.E.; Rhoades, W.A. (1 July 1980). "Conceptual design characteristics of a denatured molten-salt reactor with once-through fueling": ORNL/TM–7207, 5352526. doi:10.2172/5352526. OSTI 5352526. Cite journal requires
|journal=
(help) - ^ Jump up to: a b "A Technology Roadmap for Generation IV Nuclear Energy Systems" (PDF). 1 March 2003: GIF–001–00, 859105. doi:10.2172/859105. OSTI 859105. S2CID 46766688. Archived from the original (PDF) on 28 February 2019. Cite journal requires
|journal=
(help) - ^ Jump up to: a b c "The UK's Forgotten Molten Salt Reactor Programme". The Alvin Weinberg Foundation. Archived from the original on 5 March 2016.
- ^ Smith, J; Simmons, W E (eds.). "An Assessment of a 2500 MEe Molten Chloride Salt Fast Reactor" (PDF). United Kingdom Atomic Energy Authority Reactor Group. Retrieved 13 June 2015.
- ^ May, W C; Simmons, W E (eds.). "Conceptual Design and Assessment of a Helium-cooled 2500 MEe Molten Salt Reactor With Integrated Gas Turbine Plant" (PDF). United Kingdom Atomic Energy Authority Reactor Group. Retrieved 13 June 2015.
- ^ Novikov, Vladimir M. (15 September 1995). "The results of the investigations of Russian Research Center—'Kurchatov Institute' on molten salt applications to problems of nuclear energy systems". AIP Conference Proceedings. 346 (1): 138–147. Bibcode:1995AIPC..346..138N. doi:10.1063/1.49148.
- ^ A reduction in activity occurred after 1986 due to the Chernobyl accident, along with a general stagnation of nuclear power and the nuclear industry.
- ^ Agency, Nuclear Energy; OECD (1999). Advanced Reactors with Innovative Fuels. p. 381. ISBN 978-9264171176.
- ^ Greenblatt, Jeffery B.; Brown, Nicholas R.; Slaybaugh, Rachel; Wilks, Theresa; Stewart, Emma; McCoy, Sean T. (17 October 2017). "The Future of Low-Carbon Electricity". Annual Review of Environment and Resources. 42 (1): 289–316. doi:10.1146/annurev-environ-102016-061138. Retrieved 25 June 2021.
- ^ Integral Molten Salt Reactor. terrestrialenergy.com
- ^ "Pre-Licensing Vendor Design Review". Canadian Nuclear Safety Commission. 3 February 2014. Retrieved 10 November 2017.
- ^ Jump up to: a b Evans-Pritchard, Ambrose (6 January 2013) China blazes trail for 'clean' nuclear power from thorium The Daily Telegraph, UK. Accessed 18 March 2013
- ^ Clark, Duncan (16 February 2011). "China enters race to develop nuclear energy from thorium". The Guardian.
- ^ Halper, Mark. "China eyes thorium MSRs for industrial heat, hydrogen; revises timeline". Weinberg Next Nuclear. The Alvin Weinberg Foundation. Retrieved 9 June 2016.
- ^ Jump up to: a b Chen, Stephen (5 December 2017). "China Hopes Cold War Nuclear Energy Tech Will Power Warships, Drones". South China Morning Post. Retrieved 4 May 2018.
- ^ Tennenbaum, Jonathan (4 February 2020). "Molten salt and traveling wave nuclear reactors". Asia Times. Retrieved 30 September 2020.
- ^ "Research clarifies origin of superior properties of new materials for next-generation molten salt reactors - ANSTO". ansto.gov.au.
- ^ "Molten salt reactor research develops class of alloys". world-nuclear-news.org. World Nuclear News.
- ^ Lavars, Nick (20 July 2021). "China adding finishing touches to world-first thorium nuclear reactor". New Atlas.
- ^ Wang, Brian. "China's Molten Salt Nuclear Reactors | NextBigFuture.com". Retrieved 24 August 2021.
- ^ "Advances in Small Modular Reactor Technology Developments" (PDF). International Atomic Energy Agency (IAEA). Retrieved 22 December 2019.
- ^ Copenhagen Atomics - Thomas Jam Pedersen @ TEAC10. YouTube. 17 November 2019. Retrieved 22 December 2019.
- ^ "Seaborg Making nuclear sustainable" (PDF). Dual Ports. 2019.
- ^ "Seaborg: Rethinking Nuclear". Seaborg. Retrieved 28 June 2021.
- ^ "European Commission : CORDIS : Projects & Results Service : Periodic Report Summary – EVOL (Evaluation and viability of liquid fuel fast reactor system)". Archived from the original on 13 April 2016.
- ^ "EVOL (Project n°249696) Final Report" (PDF).
- ^ Serp, Jérôme; Allibert, Michel; Beneš, Ondřej; Delpech, Sylvie; Feynberg, Olga; Ghetta, Véronique; Heuer, Daniel; Holcomb, David; Ignatiev, Victor; Kloosterman, Jan Leen; Luzzi, Lelio; Merle-Lucotte, Elsa; Uhlíř, Jan; Yoshioka, Ritsuo; Zhimin, Dai (1 November 2014). "The molten salt reactor (MSR) in generation IV: Overview and perspectives". Progress in Nuclear Energy. 77: 308–319. doi:10.1016/j.pnucene.2014.02.014.
- ^ "SAMOFAR home". SAMOFAR. Retrieved 31 August 2018.
- ^ Vijayan, P. K.; Basak, A.; Dulera, I. V.; Vaze, K. K.; Basu, S.; Sinha, R. K. (1 September 2015). "Conceptual design of Indian molten salt breeder reactor". Pramana. 85 (3): 539–554. Bibcode:2015Prama..85..539V. doi:10.1007/s12043-015-1070-0. S2CID 117404500.
- ^ "Indian Molten Salt Breeder Reactor (IMSBR) Initiated". Thorium Energy World. Retrieved 31 August 2018.
- ^ Fuji Molten salt reactor Archived 5 February 2010 at the Wayback Machine. nextbigfuture.com. 19 December 2007
- ^ Jump up to: a b Barton, Charles (March 2008) Interview with Ralph Moir at Energy From Thorium blog
- ^ "Росатом запустил проект ядерного реактора-"сжигателя" опасных веществ" [Rosatom launches project of burner reactor], РИА Новости (in Russian), Moscow, 11 June 2020, retrieved 11 February 2021
- ^ Ганжур, Ольга (12 April 2020). "Жидкосолевой реактор на ГХК планируют запустить к 2031 году" [Molten salt reactor at MCC is planned to be launched in 2031]. Страна РОСАТОМ (in Russian). Retrieved 11 February 2021.
- ^ Clark, Duncan (9 September 2011). "Thorium advocates launch pressure group". The Guardian.
- ^ "London: Weinberg Foundation to heat up campaign for safe, green,... – The Weinberg Foundation" Archived 30 October 2011 at the Wayback Machine. Mynewsdesk.
- ^ "New NGO to fuel interest in safe thorium nuclear reactors". businessgreen.com.
- ^ Griffiths, Trevor; Tomlinson, Jasper; O’Sullivan, Rory. "MSR Review – Feasibility of Developing a Pilot Scale Molten Salt Reactor in the UK" (PDF). Energy Process Developments. Retrieved 14 January 2016.
- ^ Ian Scott (20 June 2017), "Molten Salt Reactors", The Nuclear Institute UK, retrieved 18 March 2018 – via YouTube[dead link]
- ^ "Moltex partners in New Brunswick SMR project", World Nuclear News, 16 July 2018
- ^ "Karios, Moltex, See Progress in Funding; First Canadian SMR, an HTGR, Submits License Application to CNSC", Neutron Bytes, 6 April 2019
- ^ "Current pre-licensing vendor design reviews", Canadian Nuclear Safety Commission, 3 February 2014, retrieved 8 June 2020
- ^ Ehresman, Teri (ed.). Molten Salt Reactor (MSR) (PDF) (Fact Sheet). 08-GA50044-17-R1 R6-11. Idaho National Laboratory.
- ^ Jump up to: a b Kirk Sorensen has Started a Thorium Power Company Archived 26 October 2011 at the Wayback Machine at NextBigFuture blog, 23 May 2011
- ^ "Flibe Energy". flibe-energy.com.
- ^ "Live chat: nuclear thorium technologist Kirk Sorensen". The Guardian. 7 September 2011.
- ^ "New Huntsville company to build thorium-based nuclear reactors" Archived 6 April 2012 at the Wayback Machine. huntsvillenewswire.com.
- ^ "New nuke could power world until 2083". The Register. 14 March 2013.
- ^ Transatomic (25 September 2018). "Transatomic Power". Twitter. Retrieved 13 October 2019.
- ^ "Energy Department Announces New Investments in Advanced Nuclear Power Reactors..." US Department of Energy. Retrieved 16 January 2016.
- ^ Patel, Sonal (6 May 2021). "TVA, Kairos Partner to Deploy Molten Salt Nuclear Reactor Demonstration". POWER. Retrieved 28 June 2021.
- ^ Jump up to: a b Wang, Brian (26 August 2018). "Global race for transformative molten salt nuclear includes Bill Gates and China". NextBigFuture.com. Retrieved 2 September 2018.
- ^ Gat, U.; Engel, J. R.; Dodds, H. L. (1 January 1991). The Molten Salt Reactor option for beneficial use of fissile material from dismantled weapons. Annual meeting of the American Association for the Advancement of Science: earth science. OSTI 5717860.
- ^ Fluoride Salt-Cooled High-Temperature Reactor Workshop Announcement and Call for Participation, September 2010, at Oak Ridge National Laboratory, Oak Ridge Tennessee
- ^ Hargraves, Robert; Moir, Ralph (2010). "Liquid Fluoride Thorium Reactors". American Scientist. 98 (4): 304–313. doi:10.1511/2010.85.304. JSTOR 27859537. ProQuest 847558669.
- ^ Van Gosen, B. S.; Armbrustmacher, T. J. (2009), Thorium deposits of the United States – Energy resources for the future?, Circular 1336, U.S. Geological Survey
- ^ Greene, Sherrel (May 2011). "Fluoride Salt-cooled High Temperature Reactors – Technology Status and Development Strategy". ICENES-2011. San Francisco, CA.
- ^ Forsberg, Charles (November 2011) Fluoride-Salt-Cooled High-Temperature Reactors for Power and Process Heat. mit.edu
- ^ Ingersoll, D. T. (December 2005). "ORNL/TM-2005/218, Status of Physics and Safety Analyses for the Liquid-Salt-Cooled Very High-Temperature Reactor (LS-VHTR)". ORNL. Retrieved 13 May 2010.
- ^ Baron, Matthias; Böck, Helmuth; Villa, Mario. "TRIGA Reactor Characteristics". IAEA Education and Training. IAEA. Retrieved 2 June 2016.
- ^ Gylfe, J.D. "US Patent 3,145,150, Aug. 18, 1954, Fuel Moderator Element for a Nuclear Reactor, and Method of Making". U.S. Patent Office. U.S. Government. Retrieved 2 June 2016.
- ^ Massie, Mark; Dewan, Leslie C. "US 20130083878 A1, April 4, 2013, Nuclear Reactors and Related Methods and Apparatus". U.S. Patent Office. U.S. Government. Retrieved 2 June 2016.
- ^ Jump up to: a b c Shaffer, J.H. (1 January 1971). "Preparation and Handling of Salt Mixtures for the Molten Salt Reactor Experiment": ORNL––4616, 4074869. doi:10.2172/4074869. OSTI 4074869. Cite journal requires
|journal=
(help) - ^ Ignatiev, Victor (1 April 2010). Critical issues of nuclear energy systems employing molten salt fluorides (PDF). Lisbon, Portugal: ACSEPT. Archived from the original (PDF) on 13 April 2016. Retrieved 18 December 2011.
- ^ C. Forsberg, Charles (June 2004). "Safety and Licensing Aspects of the Molten Salt Reactor" (PDF). 2004 American Nuclear Society Annual Meeting. Pittsburgh, PA: American Nuclear Society. Archived from the original (PDF) on 13 January 2010. Retrieved 12 September 2009.
- ^ Jump up to: a b Andrews, Anthony (27 March 2008), "Nuclear Fuel Processing: U.S. Policy Development" (PDF), CRS Report for Congress, RS22542
- ^ Rosenthal, M.; Briggs, R.; Haubenreich, P. (1 January 1971). "Molten-Salt Reactor Program: Semiannual Progress Report for Period Ending August 31, 1971": ORNL––4676, 4743040. doi:10.2172/4743040. OSTI 4743040. Cite journal requires
|journal=
(help) - ^ LeBlanc, D (2010). "Denatured Molten Salt Reactors (DMSR): An Idea Whose Time Has Finally Come?". 31st Annual Conference of the Canadian Nuclear Society & 34th CNS: Montreal, Quebec, Canada, 24-27 May, 2010. Canadian Nuclear Society. ISBN 978-1-61782-363-3. S2CID 53394595.
- ^ Furukawa, Kazuo; Kato, Yoshio; Chigrinov, Sergey E. (1995). "Plutonium (TRU) transmutation and 233U production by single-fluid type accelerator molten-salt breeder (AMSB)". AIP Conference Proceedings. 346 (1): 745–751. Bibcode:1995AIPC..346..745F. doi:10.1063/1.49112.
- ^ Moir, M. W. (2002). "Cost of Electricity from Molten Salt Reactors (MSR)" (PDF). 138. Nuclear Technology: 93–95. Cite journal requires
|journal=
(help) - ^ Finnish research network for generation four nuclear energy systems. vtt.fi
- ^ "Is the "Superfuel" Thorium Riskier Than We Thought?". Popular Mechanics. 5 December 2012.
- ^ "Transatomic Power White Paper, v1.0.1, section 1.2" (PDF). Transatomic Power Inc. Archived from the original (PDF) on 5 July 2015. Retrieved 2 June 2016.
Further reading[]
- Energy from Thorium's Document Repository Contains scanned versions of many of the U.S. government engineering reports, over ten thousand pages of construction and operation experience. This repository is the main reference for the aircraft reactor experiment and molten-salt fueled reactor's technical discussion.
- Weinberg, Alvin M. (1994). The First Nuclear Era: The Life and Times of a Technological Fixer. Springer Science & Business Media. ISBN 978-1-56396-358-2.
- Bruce Hoglund's Eclectic Interests Home Page Nuclear Power, Thorium, Molten Salt reactors, etc.
- Generation IV International Forum MSR website
- INL MSR workshop summary
- "Molten Salt Chemistry Plays a Prominent Role in Accelerator-Driven Transmutation Systems". Archived from the original on 21 February 2013.
- Material Considerations for Molten Salt Accelerator-based Plutonium Conversion Systems J.H. Devan et al.
- Nuclear goes retro – with a much greener outlook M. Mitchell Waldrop
- Lane, James. A (1958). Fluid Fuel Reactors. Addison-Wesley & US AEC. p. 972.
External links[]
![]() |
Wikimedia Commons has media related to Molten salt reactors. |
- Pacific Northwest National Laboratory – Molten Salt Reactor Fundamentals YouTube
- International Thorium Energy Organisation – www.IThEO.org
- The Molten-Salt Reactor Experiment on YouTube
- Idaho National Laboratory Molten Salt Reactor Fact Sheet
- Energy from Thorium Blog / Website
- Google TechTalks – “Liquid Fluoride Thorium Reactor: What Fusion Wanted To Be” by Dr. Joe Bonometti NASA / Naval Postgraduate School YouTube
- Pebble Bed Advanced High Temperature Reactor
- Thorium Remix LFTR in 5 Minutes and other LFTR Documentaries.
- Kun Chen from Chinese Academy of Sciences on China Thorium Molten Salt Reactor TMSR Program
- Review of Molten Salt Reactor Technology
- "MSFR – Bibliography". Archived from the original on 16 November 2015.
- Heuer, D.; Merle-Lucotte, E.; Allibert, M.; Brovchenko, M.; Ghetta, V.; Rubiolo, P. (1 February 2014). "Towards the thorium fuel cycle with molten salt fast reactors". Annals of Nuclear Energy. 64: 421–429. doi:10.1016/j.anucene.2013.08.002.
- Lavars, Nick (20 July 2021). "China adding finishing touches to world-first thorium nuclear reactor". New Atlas. Retrieved 21 July 2021.
- Nuclear power reactor types
- Graphite moderated reactors
- Beryllium moderated reactors