Radioisotope thermoelectric generator

Diagram of an RTG used on the Cassini probe

A radioisotope thermoelectric generator (RTG, RITEG) is a type of nuclear battery that uses an array of thermocouples to convert the heat released by the decay of a suitable radioactive material into electricity by the Seebeck effect. This type of generator has no moving parts.

RTGs have been used as power sources in satellites, space probes, and uncrewed remote facilities such as a series of lighthouses built by the Soviet Union inside the Arctic Circle. RTGs are usually the most desirable power source for unmaintained situations that need a few hundred watts (or less) of power for durations too long for fuel cells, batteries, or generators to provide economically, and in places where solar cells are not practical. Safe use of RTGs requires containment of the radioisotopes long after the productive life of the unit. The expense of RTGs tends to limit their use to niche applications in rare or special situations.

History[]

A pellet of ²³⁸PuO₂ as used in the RTG for the Cassini and Galileo missions. This photo was taken after insulating the pellet under a graphite blanket for several minutes and then removing the blanket. The pellet is glowing red hot because of the heat generated by radioactive decay (primarily α). The initial output is 62 watts.

The RTG was invented in 1954 by Mound Laboratories scientists Ken Jordan and John Birden. They were inducted into the National Inventors Hall of Fame in 2013.^[1][2] Jordan and Birden worked on an Army Signal Corps contract (R-65-8- 998 11-SC-03-91) beginning on 1 January 1957, to conduct research on radioactive materials and thermocouples suitable for the direct conversion of heat to electrical energy using polonium-210 as the heat source. RTGs were developed in the US during the late 1950s by Mound Laboratories in Miamisburg, Ohio, under contract with the United States Atomic Energy Commission. The project was led by Dr. Bertram C. Blanke.^[3]

The first RTG launched into space by the United States was SNAP 3B in 1961 powered by 96 grams of plutonium-238 metal, aboard the Navy Transit 4A spacecraft. One of the first terrestrial uses of RTGs was in 1966 by the US Navy at uninhabited Fairway Rock in Alaska. RTGs were used at that site until 1995.

A common RTG application is spacecraft power supply. Systems for Nuclear Auxiliary Power (SNAP) units were used for probes that traveled far from the Sun rendering solar panels impractical. As such, they were used with Pioneer 10, Pioneer 11, Voyager 1, Voyager 2, Galileo, Ulysses, Cassini, New Horizons, and the Mars Science Laboratory. RTGs were used to power the two Viking landers and for the scientific experiments left on the Moon by the crews of Apollo 12 through 17 (SNAP 27s). Because the Apollo 13 Moon landing was aborted, its RTG rests in the South Pacific Ocean, in the vicinity of the Tonga Trench.^[4] RTGs were also used for the Nimbus, Transit and LES satellites. By comparison, only a few space vehicles have been launched using full-fledged nuclear reactors: the Soviet RORSAT series and the American SNAP-10A.

In addition to spacecraft, the Soviet Union built 1007 RTGs^[5] to power uncrewed lighthouses and navigation beacons on the Soviet arctic coast by the late 1980s.^[5][6] Many different types of RTGs were built in the Soviet Union, for a wide variety of purposes. The lighthouses were not maintained for many years after the dissolution of the Soviet Union in 1991. Some of the RTG units disappeared during this time—either by looting or by the natural forces of ice/storm/sea.^[5] In 1996, a project was begun by Russian and international supporters to decommission the RTGs in the lighthouses, and by 2021, all RTGs are now removed.^[5]

As of 1992, the United States Air Force also used RTGs to power remotely-located Arctic equipment, and the US government has used hundreds of such units to power remote stations globally. Sensing stations for Top-ROCC and radar systems, predominantly located in Alaska, use RTGs. The units use strontium-90, and a larger number of such units have been deployed both on the ground and on the ocean floor than have been used on spacecraft, with public regulatory documents suggesting that the US had deployed at least 100–150 during the 1970s and 1980s.^{[7][needs update]}

In the past, small "plutonium cells" (very small ²³⁸Pu-powered RTGs) were used in implanted heart pacemakers to ensure a very long "battery life".^[8] As of 2004, about ninety were still in use. By the end of 2007, the number was reported to be down to just nine.^[9] The Mound Laboratory Cardiac Pacemaker program began on 1 June 1966, in conjunction with NUMEC.^[10] When it was recognized that the heat source would not remain intact during cremation, the program was cancelled in 1972 because there was no way to completely ensure that the units would not be cremated with their users' bodies.

Design[]

The design of an RTG is simple by the standards of nuclear technology: the main component is a sturdy container of a radioactive material (the fuel). Thermocouples are placed in the walls of the container, with the outer end of each thermocouple connected to a heat sink. Radioactive decay of the fuel produces heat. It is the temperature difference between the fuel and the heat sink that allows the thermocouples to generate electricity.

A thermocouple is a thermoelectric device that can convert thermal energy directly into electrical energy, using the Seebeck effect. It is made of two kinds of metal (or semiconductors) that can both conduct electricity. If they are connected to each other in a closed loop and the two junctions are at different temperatures, an electric current will flow in the loop. Typically a large number of thermocouples are connected in series to generate a higher voltage.

Fuels[]

• 

  Inspection of Cassini spacecraft RTGs before launch

• 

  New Horizons in assembly hall

Criteria for selection of isotopes[]

The radioactive material used in RTGs must have several characteristics:^[11]

1. Its half-life must be long enough so that it will release energy at a relatively constant rate for a reasonable amount of time. The amount of energy released per time (power) of a given quantity is inversely proportional to half-life. An isotope with twice the half-life and the same energy per decay will release power at half the rate per mole. Typical half-lives for radioisotopes used in RTGs are therefore several decades, although isotopes with shorter half-lives could be used for specialized applications.
2. For spaceflight use, the fuel must produce a large amount of power per mass and volume (density). Density and weight are not as important for terrestrial use, unless there are size restrictions. The decay energy can be calculated if the energy of radioactive radiation or the mass loss before and after radioactive decay is known. Energy release per decay is proportional to power production per mole. Alpha decays in general release about ten times as much energy as the beta decay of strontium-90 or caesium-137.^{[citation needed]}
3. Radiation must be of a type easily absorbed and transformed into thermal radiation, preferably alpha radiation. Beta radiation can emit considerable gamma/X-ray radiation through bremsstrahlung secondary radiation production and therefore requires heavy shielding. Isotopes must not produce significant amounts of gamma, neutron radiation or penetrating radiation in general through other decay modes or decay chain products.

The first two criteria limit the number of possible fuels to fewer than thirty atomic isotopes^[11] within the entire table of nuclides.

Plutonium-238, curium-244 and strontium-90 are the most often cited candidate isotopes, but other isotopes such as polonium-210, promethium-147, caesium-137, cerium-144, ruthenium-106, cobalt-60, curium-242, americium-241 and thulium isotopes have also been studied.^{[citation needed]}

²³⁸Pu[]

Plutonium-238 has a half-life of 87.7 years, reasonable power density of 0.57 watts per gram,^[12] and exceptionally low gamma and neutron radiation levels. ²³⁸Pu has the lowest shielding requirements. Only three candidate isotopes meet the last criterion (not all are listed above) and need less than 25 mm of lead shielding to block the radiation. ²³⁸Pu (the best of these three) needs less than 2.5 mm, and in many cases, no shielding is needed in a ²³⁸Pu RTG, as the casing itself is adequate. ²³⁸Pu has become the most widely used fuel for RTGs, in the form of plutonium(IV) oxide (PuO₂).^{[citation needed]} However, plutonium(IV) oxide containing a natural abundance of oxygen emits neutrons at the rate of ~23x10³ n/sec/g of plutonium-238. This emission rate is relatively high compared to the neutron emission rate of plutonium-238 metal. The metal containing no light element impurities emits ~2.8x10³ n/sec/g of plutonium-238. These neutrons are produced by the spontaneous fission of plutonium-238.

The difference in the emission rates of the metal and the oxide is due mainly to the alpha, neutron reaction with the oxygen-18 and oxygen-17 present in the oxide. The normal amount of oxygen-18 present in the natural form is 0.204% while that of oxygen-17 is 0.037%. The reduction of the oxygen-17 and oxygen-18 present in plutonium dioxide will result in a much lower neutron emission rate for the oxide; this can be accomplished by a gas phase ¹⁶O₂ exchange method. Regular production batches of ²³⁸PuO₂ particles precipitated as a hydroxide were used to show that large production batches could be effectively ¹⁶O₂-exchanged on a routine basis. High-fired ²³⁸PuO₂ microspheres were successfully ¹⁶O₂-exchanged showing that an exchange will take place regardless of the previous heat treatment history of the ²³⁸PuO₂.^[13] This lowering of the neutron emission rate of PuO₂ containing normal oxygen by a factor of five was discovered during the cardiac pacemaker research at Mound Laboratory in 1966, due in part to the Mound Laboratory's experience with production of stable isotopes beginning in 1960. For production of the large heat sources the shielding required would have been prohibitive without this process.^[14]

Unlike the other three isotopes discussed in this section, ²³⁸Pu must be specifically synthesized and is not abundant as a nuclear waste product. At present only Russia has maintained high-volume production, while in the US, no more than 50 g (1.8 oz) were produced in total between 2013 and 2018.^[15] The US agencies involved desire to begin the production of the material at a rate of 300 to 400 grams (11 to 14 oz) per year. If this plan is funded, the goal would be to set up automation and scale-up processes in order to produce an average of 1.5 kg (3.3 lb) per year by 2025.^[16][15]

⁹⁰Sr[]

Strontium-90 has been used by the Soviet Union in terrestrial RTGs. ⁹⁰Sr decays by β emission, with minor γ emission. While its half life of 28.8 years is much shorter than that of ²³⁸Pu, it also has a lower decay energy with a power density of 0.46 watts per gram.^[17] Because the energy output is lower it reaches lower temperatures than ²³⁸Pu, which results in lower RTG efficiency. ⁹⁰Sr is a high yield waste product of nuclear fission and is available in large quantities at a low price.^[17]

²¹⁰Po[]

Some prototype RTGs, first built in 1958 by the US Atomic Energy Commission, have used polonium-210. This isotope provides phenomenal power density (pure ²¹⁰Po emits 140 W/g) because of its high decay rate, but has limited use because of its very short half-life of 138 days. A half-gram sample of ²¹⁰Po reaches temperatures of over 500 °C (900 °F).^[18] As Po-210 is a pure alpha-emitter and does not emit significant gamma or X-ray radiation, the shielding requirements are also low as for Pu-238.

²⁴¹Am[]

Americium-241 is a potential candidate isotope with a longer half-life than ²³⁸Pu: ²⁴¹Am has a half-life of 432 years and could hypothetically power a device for centuries. However, the power density of ²⁴¹Am is only 1/4 that of ²³⁸Pu, and ²⁴¹Am produces more penetrating radiation through decay chain products than ²³⁸Pu and needs more shielding. Its shielding requirements in a RTG are the third lowest: only ²³⁸Pu and ²¹⁰Po require less. With a current global shortage^[19] of ²³⁸Pu, ²⁴¹Am is being studied as RTG fuel by ESA^[20] and in 2019, UK's National Nuclear Laboratory announced the generation of usable electricity.^[21] An advantage over ²³⁸Pu is that it is produced as nuclear waste and is nearly isotopically pure. Prototype designs of ²⁴¹Am RTGs expect 2-2.2 W_e/kg for 5–50 W_e RTGs design, putting ²⁴¹Am RTGs at parity with ²³⁸Pu RTGs within that power range.^[22]

²⁵⁰Cm[]

Curium-250 is the smallest transuranic isotope that primarily decays by spontaneous fission, a process that releases many times more energy than alpha decay. Compared to Plutonium-238, Curium-250 provides about a quarter of the power density, but 1000 times the half-life.

Life span[]

⁹⁰Sr-powered Soviet RTGs in dilapidated condition.

Most RTGs use ²³⁸Pu, which decays with a half-life of 87.7 years. RTGs using this material will therefore diminish in power output by a factor of 1 – (1/2)^1/87.7, which is 0.787%, per year.

One example is the MHW-RTG used by the Voyager probes. In the year 2000, 23 years after production, the radioactive material inside the RTG had decreased in power by 16.6%, i.e. providing 83.4% of its initial output; starting with a capacity of 470 W, after this length of time it would have a capacity of only 392 W. A related loss of power in the Voyager RTGs is the degrading properties of the bi-metallic thermocouples used to convert thermal energy into electrical energy; the RTGs were working at about 67% of their total original capacity instead of the expected 83.4%. By the beginning of 2001, the power generated by the Voyager RTGs had dropped to 315 W for Voyager 1 and to 319 W for Voyager 2.^[23]

Multi-Mission Radioisotope Thermoelectric Generator[]

NASA has developed a multi-mission radioisotope thermoelectric generator (MMRTG) in which the thermocouples would be made of skutterudite, a cobalt arsenide (CoAs₃), which can function with a smaller temperature difference than the current tellurium-based designs. This would mean that an otherwise similar RTG would generate 25% more power at the beginning of a mission and at least 50% more after seventeen years. NASA hopes to use the design on the next New Frontiers mission.^[24]

Efficiency[]

This section possibly contains original research. Please by verifying the claims made and adding inline citations. Statements consisting only of original research should be removed. (March 2021) (Learn how and when to remove this template message)

RTGs use thermoelectric generators to convert heat from the radioactive material into electricity. Thermoelectric modules, though very reliable and long-lasting, are very inefficient; efficiencies above 10% have never been achieved and most RTGs have efficiencies between 3–7%. Thermoelectric materials in space missions to date have included silicon–germanium alloys, lead telluride and tellurides of antimony, germanium and silver (TAGS). Studies have been done on improving efficiency by using other technologies to generate electricity from heat. Achieving higher efficiency would mean less radioactive fuel is needed to produce the same amount of power, and therefore a lighter overall weight for the generator. This is a critically important factor in spaceflight launch cost considerations.

Thermoelectric effect
show Principles Thermoelectric effect Seebeck effect Peltier effect Thomson effect Seebeck coefficient Ettingshausen effect Nernst effect
hide Applications Thermoelectric materials Thermocouple Thermopile Thermoelectric cooling Thermoelectric generator Radioisotope thermoelectric generator Automotive thermoelectric generator
v t

A thermionic converter—an energy conversion device which relies on the principle of thermionic emission—can achieve efficiencies between 10–20%, but requires higher temperatures than those at which standard RTGs run. Some prototype ²¹⁰Po RTGs have used thermionics, and potentially other extremely radioactive isotopes could also provide power by this means, but short half-lives make these unfeasible. Several space-bound nuclear reactors have used thermionics, but nuclear reactors are usually too heavy to use on most space probes.^{[citation needed]}

Thermophotovoltaic cells work by the same principles as a photovoltaic cell, except that they convert infrared light emitted by a hot surface rather than visible light into electricity. Thermophotovoltaic cells have an efficiency slightly higher than thermoelectric modules (TEMs) and can be overlaid on top of themselves, potentially doubling efficiency. Systems with radioisotope generators simulated by electric heaters have demonstrated efficiencies of 20%,^[25] but have not yet been tested with radioisotopes.^{[citation needed]} Some theoretical thermophotovoltaic cell designs have efficiencies up to 30%, but these have yet to be built or confirmed. Thermophotovoltaic cells and silicon TEMs degrade faster than metal TEMs, especially in the presence of ionizing radiation.^{[citation needed]}

Dynamic generators can provide power at more than four times the conversion efficiency of RTGs.^{[citation needed]} NASA and DOE have been developing a next-generation radioisotope-fueled power source called the Stirling Radioisotope Generator (SRG) that uses free-piston Stirling engines coupled to linear alternators to convert heat to electricity. SRG prototypes demonstrated an average efficiency of 23%. Greater efficiency can be achieved by increasing the temperature ratio between the hot and cold ends of the generator. The use of non-contacting moving parts, non-degrading flexural bearings, and a lubrication-free and hermetically sealed environment have, in test units, demonstrated no appreciable degradation over years of operation. Experimental results demonstrate that an SRG could continue running for decades without maintenance. Vibration can be eliminated as a concern by implementation of dynamic balancing or use of dual-opposed piston movement. Potential applications of a Stirling radioisotope power system include exploration and science missions to deep-space, Mars, and the Moon.^{[citation needed]}

The increased efficiency of the SRG may be demonstrated by a theoretical comparison of thermodynamic properties, as follows. These calculations are simplified and do not account for the decay of thermal power input due to the long half-life of the radioisotopes used in these generators. The assumptions for this analysis include that both systems are operating at steady state under the conditions observed in experimental procedures (see table below for values used). Both generators can be simplified to heat engines to be able to compare their current efficiencies to their corresponding Carnot efficiencies. The system is assumed to be the components, apart from the heat source and heat sink.^[26][27][28]

The thermal efficiency, denoted η_th, is given by:^{[citation needed]}

${\displaystyle \eta _{\text{th}}={\frac {\text{Desired Output}}{\text{Required Input}}}={\frac {W'_{\text{out}}}{Q'_{\text{in}}}}}$

where primes ( ' ) denote the time derivative.

From a general form of the First Law of Thermodynamics, in rate form:

${\displaystyle \Delta E'^{\text{sys}}=Q'_{\text{in}}+W'_{\text{in}}-Q'_{\text{out}}-W'_{\text{out}}\,}$

Assuming the system is operating at steady state and ${\displaystyle W'_{\text{in}}=0\,}$,

${\displaystyle W'_{\text{out}}=Q'_{\text{in}}-Q'_{\text{out}}\,}$

η_th, then, can be calculated to be 110 W / 2000 W = 5.5% (or 140 W / 500 W = 28% for the SRG).^{[clarification needed]} Additionally, the Second Law efficiency, denoted η_II, is given by:

${\displaystyle \eta _{\text{II}}={\frac {\eta _{\text{th}}}{\eta _{\text{th, rev}}}}}$

where η_{th, rev} is the Carnot efficiency, given by:

${\displaystyle \eta _{\text{th}}=1-{\frac {T_{\text{heat sink}}}{T_{\text{heat source}}}}}$

in which T_{heat sink} is the external temperature (which has been measured to be 510 K for the MMRTG (Multi-Mission RTG) and 363 K for the SRG) and T_{heat source} is the temperature of the MMRTG, assumed 823 K (1123 K for the SRG). This yields a Second Law efficiency of 14.46% for the MMRTG (or 41.37% for the SRG).^{[citation needed]}

Safety[]

Diagram of a stack of general purpose heat source modules as used in RTGs

Theft[]

Radioactive materials contained in RTGs are dangerous and can even be used for malicious purposes. They are barely useful for a genuine nuclear weapon, but still can serve in a "dirty bomb". The Soviet Union constructed many uncrewed lighthouses and navigation beacons powered by RTGs using strontium-90 (⁹⁰Sr). They are very reliable and provide a steady source of power. Most have no protection, not even fences or warning signs, and the locations of some of these facilities are no longer known due to poor record keeping. In one instance, the radioactive compartments were opened by a thief.^[6] In another case, three woodsmen in Tsalendzhikha Region, Georgia found two ceramic RTG orphan sources that had been stripped of their shielding; two of them were later hospitalized with severe radiation burns after carrying the sources on their backs. The units were eventually recovered and isolated.^[29] There are approximately 1,000 such RTGs in Russia, all of which have long since exceeded their designed operational lives of ten years. Most of these RTGs likely no longer function, and may need to be dismantled. Some of their metal casings have been stripped by metal hunters, despite the risk of radioactive contamination.^[30]

Radioactive contamination[]

RTGs pose a risk of radioactive contamination: if the container holding the fuel leaks, the radioactive material may contaminate the environment.

For spacecraft, the main concern is that if an accident were to occur during launch or a subsequent passage of a spacecraft close to Earth, harmful material could be released into the atmosphere; therefore their use in spacecraft and elsewhere has attracted controversy.^[31][32]

However, this event is not considered likely with current RTG cask designs. For instance, the environmental impact study for the Cassini–Huygens probe launched in 1997 estimated the probability of contamination accidents at various stages in the mission. The probability of an accident occurring which caused radioactive release from one or more of its 3 RTGs (or from its 129 radioisotope heater units) during the first 3.5 minutes following launch was estimated at 1 in 1,400; the chances of a release later in the ascent into orbit were 1 in 476; after that the likelihood of an accidental release fell off sharply to less than 1 in a million.^[33] If an accident which had the potential to cause contamination occurred during the launch phases (such as the spacecraft failing to reach orbit), the probability of contamination actually being caused by the RTGs was estimated at about 1 in 10.^[34] The launch was successful and Cassini–Huygens reached Saturn.

To minimize the risk of the radioactive material being released, the fuel is stored in individual modular units with their own heat shielding. They are surrounded by a layer of iridium metal and encased in high-strength graphite blocks. These two materials are corrosion- and heat-resistant. Surrounding the graphite blocks is an aeroshell, designed to protect the entire assembly against the heat of reentering the Earth's atmosphere. The plutonium fuel is also stored in a ceramic form that is heat-resistant, minimising the risk of vaporization and aerosolization. The ceramic is also highly insoluble.

The plutonium-238 used in these RTGs has a half-life of 87.74 years, in contrast to the 24,110 year half-life of plutonium-239 used in nuclear weapons and reactors. A consequence of the shorter half-life is that plutonium-238 is about 275 times more radioactive than plutonium-239 (i.e. 17.3 curies (640 GBq)/g compared to 0.063 curies (2.3 GBq)/g^[35]). For instance, 3.6 kg of plutonium-238 undergoes the same number of radioactive decays per second as 1 tonne of plutonium-239. Since the morbidity of the two isotopes in terms of absorbed radioactivity is almost exactly the same,^[36] plutonium-238 is around 275 times more toxic by weight than plutonium-239.

The alpha radiation emitted by either isotope will not penetrate the skin, but it can irradiate internal organs if plutonium is inhaled or ingested. Particularly at risk is the skeleton, the surface of which is likely to absorb the isotope, and the liver, where the isotope will collect and become concentrated.

Accidents[]

There have been several known accidents involving RTG-powered spacecraft:

1. The first one was a launch failure on 21 April 1964 in which the U.S. Transit-5BN-3 navigation satellite failed to achieve orbit and burned up on re-entry north of Madagascar.^[37] The 17,000 Ci (630 TBq) plutonium metal fuel in its SNAP-9a RTG was injected into the atmosphere over the Southern Hemisphere where it burned up, and traces of plutonium-238 were detected in the area a few months later. This incident resulted in the NASA Safety Committee requiring intact reentry in future RTG launches, which in turn impacted the design of RTGs in the pipeline.
2. The second was the Nimbus B-1 weather satellite whose launch vehicle was deliberately destroyed shortly after launch on 21 May 1968 because of erratic trajectory. Launched from the Vandenberg Air Force Base, its SNAP-19 RTG containing relatively inert plutonium dioxide was recovered intact from the seabed in the Santa Barbara Channel five months later and no environmental contamination was detected.^[38]
3. In 1969 the launch of the first Lunokhod lunar rover mission failed, spreading polonium 210 over a large area of Russia^[39]
4. The failure of the Apollo 13 mission in April 1970 meant that the Lunar Module reentered the atmosphere carrying an RTG and burned up over Fiji. It carried a SNAP-27 RTG containing 44,500 Ci (1,650 TBq) of plutonium dioxide in a graphite cask on the lander leg which survived reentry into the Earth's atmosphere intact, as it was designed to do, the trajectory being arranged so that it would plunge into 6–9 kilometers of water in the Tonga trench in the Pacific Ocean. The absence of plutonium-238 contamination in atmospheric and seawater sampling confirmed the assumption that the cask is intact on the seabed. The cask is expected to contain the fuel for at least 10 half-lives (i.e. 870 years). The US Department of Energy has conducted seawater tests and determined that the graphite casing, which was designed to withstand reentry, is stable and no release of plutonium should occur. Subsequent investigations have found no increase in the natural background radiation in the area. The Apollo 13 accident represents an extreme scenario because of the high re-entry velocities of the craft returning from cis-lunar space (the region between Earth's atmosphere and the Moon). This accident has served to validate the design of later-generation RTGs as highly safe.
5. Mars 96 was launched by Russia in 1996, but failed to leave Earth orbit, and re-entered the atmosphere a few hours later. The two RTGs onboard carried in total 200 g of plutonium and are assumed to have survived reentry as they were designed to do. They are thought to now lie somewhere in a northeast-southwest running oval 320 km long by 80 km wide which is centred 32 km east of Iquique, Chile.^[40]

A SNAP-27 RTG deployed by the astronauts of Apollo 14 identical to the one lost in the reentry of Apollo 13

One RTG, the SNAP-19C, was lost near the top of Nanda Devi mountain in India in 1965 when it was stored in a rock formation near the top of the mountain in the face of a snowstorm before it could be installed to power a CIA remote automated station collecting telemetry from the Chinese rocket testing facility. The seven capsules^[41] were carried down the mountain onto a glacier by an avalanche and never recovered. It is most likely that they melted through the glacier and were pulverized, whereupon the ²³⁸plutonium zirconium alloy fuel oxidized soil particles that are moving in a plume under the glacier.^[42]

Many Beta-M RTGs produced by the Soviet Union to power lighthouses and beacons have become orphaned sources of radiation. Several of these units have been illegally dismantled for scrap metal (resulting in the complete exposure of the Sr-90 source), fallen into the ocean, or have defective shielding due to poor design or physical damage. The US Department of Defense cooperative threat reduction program has expressed concern that material from the Beta-M RTGs can be used by terrorists to construct a dirty bomb.^[6]

Comparison with fission reactors[]

This section does not cite any sources. Please help by adding citations to reliable sources. Unsourced material may be challenged and removed. (March 2014) (Learn how and when to remove this template message)

RTGs and fission reactors use very different nuclear reactions.

Nuclear power reactors (including the miniaturized ones used in space) perform controlled nuclear fission in a chain reaction. The rate of the reaction can be controlled with neutron absorbing control rods, so power can be varied with demand or shut off (almost) entirely for maintenance. However, care is needed to avoid uncontrolled operation at dangerously high power levels, or even explosion or nuclear meltdown.

Chain reactions do not occur in RTGs. Heat is produced through spontaneous radioactive decay at a non-adjustable and steadily decreasing rate that depends only on the amount of fuel isotope and its half-life. In an RTG, heat generation cannot be varied with demand or shut off when not needed and it is not possible to save more energy for later by reducing the power consumption. Therefore, auxiliary power supplies (such as rechargeable batteries) may be needed to meet peak demand, and adequate cooling must be provided at all times including the pre-launch and early flight phases of a space mission. Spectacular failures like a nuclear meltdown or explosion are impossible with an RTG, still there is a risk of radioactive contamination if the rocket explodes, or the device reenters the atmosphere and disintegrates.

Subcritical multiplicator RTG[]

Due to the shortage of plutonium-238, a new kind of RTG assisted by subcritical reactions has been proposed.^[43] In this kind of RTG, the alpha decay from the radioisotope is also used in alpha-neutron reactions with a suitable element such as beryllium. This way a long-lived neutron source is produced. Because the system is working with a criticality close to but less than 1, i.e. K_eff < 1, a subcritical multiplication is achieved which increases the neutron background and produces energy from fission reactions. Although the number of fissions produced in the RTG is very small (making their gamma radiation negligible), because each fission reaction releases over 30 times more energy than each alpha decay (200 MeV compared to 6 MeV), up to a 10% energy gain is attainable, which translates into a reduction of the ²³⁸Pu needed per mission. The idea was proposed to NASA in 2012 for the yearly NASA NSPIRE competition, which translated to Idaho National Laboratory at the Center for Space Nuclear Research (CSNR) in 2013 for studies of feasibility.^{[44][failed verification]}. However the essentials are unmodified.

RTG for interstellar probes[]

RTG have been proposed for use on realistic interstellar precursor missions and interstellar probes.^[45] An example of this is the Innovative Interstellar Explorer (2003–current) proposal from NASA.^[46] An RTG using ²⁴¹Am was proposed for this type of mission in 2002.^[45] This could support mission extensions up to 1000 years on the interstellar probe, because the power output would decline more slowly over the long term than plutonium.^[45] Other isotopes for RTG were also examined in the study, looking at traits such as watt/gram, half-life, and decay products.^[45] An interstellar probe proposal from 1999 suggested using three advanced radioisotope power sources (ARPS).^[47]

The RTG electricity can be used for powering scientific instruments and communication to Earth on the probes.^[45] One mission proposed using the electricity to power ion engines, calling this method radioisotope electric propulsion (REP).^[45]

Electrostatic-boosted radioisotope heat sources[]

A power enhancement for radioisotope heat sources based on a self-induced electrostatic field has been proposed.^[48] According to the authors, enhancements of up to 10% could be attainable using beta sources.

Models[]

A typical RTG is powered by radioactive decay and features electricity from thermoelectric conversion, but for the sake of knowledge, some systems with some variations on that concept are included here.

Nuclear power systems in space[]

Known spacecraft/nuclear power systems and their fate. Systems face a variety of fates, for example, Apollo's SNAP-27 were left on the Moon.^[49] Some other spacecraft also have small radioisotope heaters, for example each of the Mars Exploration Rovers have a 1 watt radioisotope heater. Spacecraft use different amounts of material, for example MSL Curiosity has 4.8 kg of plutonium-238 dioxide,^[50] while the Cassini spacecraft had 32.7 kg.^[51]

** not really an RTG, the BES-5 Buk (БЭС-5) reactor was a fast breeder reactor which used thermocouples based on semiconductors to convert heat directly into electricity^[56][57]

*** not really an RTG, the SNAP-10A used enriched uranium fuel, zirconium hydride as a moderator, liquid sodium potassium alloy coolant, and was activated or deactivated with beryllium reflectors^[55] Reactor heat fed a thermoelectric conversion system for electrical production.^[55]

**** not really an RTG, the ASRG uses a Stirling power device that runs on radioisotope (see Stirling radioisotope generator)

Terrestrial[]

See also[]

• Alkali-metal thermal to electric converter
• Atomic battery – Devices generating electricity from radioisotope decay
• Betavoltaics
• Kilopower Reactor Using Stirling Technology
• Optoelectric nuclear battery
• Radioisotope heater units
• Radioactive isotope
• Stirling Radioisotope Generator
• Thermionic converter – Power generation device

References[]

Notes

External links[]

Wikimedia Commons has media related to Radioisotope thermoelectric generators.

• NASA Radioisotope Power Systems website – RTG page
• NASA JPL briefing, Expanding Frontiers with Radioisotope Power Systems – gives RTG information and a link to a longer presentation
• SpaceViews: The Cassini RTG Debate
• Stirling Radioisotope Generator
• DOE contributions – good links
• Idaho National Laboratory – Producer of RTGs
• Idaho National Laboratory MMRTG page with photo-based "virtual tour"